Puretec MaxiPlus MPB202B Bedienungsanleitung

DEC2021

User Guide

MaxiPlus™ Bag Filter Housing

MPB202B

For correct operation & installation, it is essential to observe these instructions.

DO NOT

DO NOT USE

LIQUID SEALANTS.

SURGE PROTECTION

REQUIRED /

NO EXTENSION CORDS.

SURGE PROTECTION

REQUIRED /

NO EXTENSION CORDS.

Puretec Customer Service

Thank you for purchasing a Puretec Bag Filter System. Your system is a patented, proven performer

manufactured from only quality materials and components and will give years of clean, fresh, invigorating

shower water free of impurities if maintained properly.

Caution: Do not use with water that is microbiologically unsafe or with water of unknown quality without

adequate disinfection before or after the system.

The system is designed for metropolitan supply water but can be used in other situations. For other types of

water supply please contact your local Puretec stockist.

The Puretec Bag Filter System cartridge needs replacing regularly to maintain optimum performance. This is

a simple procedure when following instructions. For cartridge replacements contact your stockist.

Precautions

Warning: For drinking water applications, do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system.

Caution: Filter must be protected against freezing (when used with aqueous solutions), which can cause

cracking of the lter and water leakage.

Caution: Because of the product’s limited service life and to prevent costly repairs or possible water

damage, we strongly recommend that the bottom of all plastic housings be replaced every ten years. If the

bottom of your housing has been in use for longer than this period, it should be replaced immediately. Date

the bottom of any new or replacement housing to indicate the next recommended replacement date.

Notes

•Make certain that installation complies with all state and local laws and regulations.

• Do not use wicking or sealer for tting connections into the cap of the lter. Thread seal tape is

recommended for this purpose.

• Do not install where system will be exposed to direct sunlight.

• Allow a minimum of 80 mm clearance under the lter or optional sump stand to facilitate lter

changes.

Installation Note: A water filter system/tap, like any product, has a limited life and may eventually

fail. Also sometimes failure happens early due to unforeseen circumstances. To avoid possible

property damage, this product should be regularly examined for leakage and/or deterioration and

replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak

detector, should be used in those applications where any leakage could cause property damage, and/

or the water supply should be turned off if no one is home/present.

INSTALLATION SHOULD BE COMPLETED BY QUALIFIED TRADESPEOPLE.

FAULTY OPERATION DUE TO UNQUALIFIED PERSONS WILL RESULT IN VOIDED

WARRANTY COVERAGE.

Customer Service

Installation

1. Before installing, verify that the materials of construction of the Puretec Bag Filter System are

compatible with the uid being ltered.

2. The location of the lter should include the following considerations:

(1) adequate space for ease of changing the lter bag,

(2) drainage or containment to collect drained or spilled liquid, and

(3) proper ventilation, if required.

3. When installing the system, include isolation valves for the lter and support for the lter

housing. Use caution when applying heat near the lter housing. It is best to weld or sweat all

ttings before assembly to the lter. The lter head may be mounted to the lter support using

5/16 inch x 1¼ inch long bolts. The bolt spacing is 3 inch on center and the bolt circle is 2-1/8

inch.

4. The lter must be installed in the vertical position with the inlet/outlet ports at the top. Flow

through the housing is inline. Note the inlet and outlet ports when connecting piping.

5. The lter housing is equipped with a ¼ inch NPT gauge part an the outlet for installation of a

pressure gauge (included) and a 3/8 inch NPT drain port at the base of the sump (3/8 inch NPT

ball valve supplied). The gauge or valve should be installed using thread seal tape as a thread

sealant.

Bag Selection

The Puretec Bag Filter Housing is designed for use with Puretec lter bags. Filter bags are available in 1, 5,

10, 25, 50, 100 and 200 micron. Polypropylene is the standard bag material but nylon is available upon

request.

Start-up

1. Open the inlet valve. It is recommended that the inlet valve be opened before the outlet valve to

prevent any backow.

2. Vent trapped air from the system before opening the outlet valve.

3. Open the outlet valve.

Installation Guide

Bag Replacement

The pressure dierential across the bag will remain fairly constant until the bag is approximately 80%

blinded o. It is recommended that the bag be changed when the pressure dierential reaches 15 psi.

However, this gure can vary with the type of lter bag. The bag manufacturer’s data should be consulted to

determine the actual pressure drop for replacement.

Warning: Review all precautions specic to the handling of the uid being ltered before changing the

lter bag. A lter bag that has been used with a hazardous liquid may contain residual amounts of this

material and should be handled with the same safeguards that would be used in handling any hazardous

and/or toxic material i.e. gloves, respirators, protective eyewear, etc. Filter bags should be disposed of in

accordance with federate state or local laws and requirements. Failure to follow precautions may result in

injury.

1. Close isolation valves to the lter.

2. Drain sump (See Warning above).

Note: If bag has not been changed on a timely basis it may not drain. If necessary, the liquid

contents of the used bag can be poured into the replacement bag to be ltered.

3. Unscrew sump from cap. Sump will unscrew counterclockwise.

Caution: Support sump at base while unscrewing to prevent dropping and possibly damaging

the sump or drain valve.

4. Remove basket assembly from sump (See Warning above).

5. Remove bag from basket.

6. Remove 0-ring from groove in the sump and wipe groove and 0-ring clean. Re-lubricate 0-ring

with food grade silicone lubricant or similar. Insert 0-ring in place and press into groove.

Note: This step is important to ensure a proper housing seal. Make certain the 0-ring is seated

level in the groove.

7. Insert new bag into the basket. Form the bag to the contours of the basket making sure that the

bag extends fully to the bottom of the basket.

Note: Make sure the lter bag overlaps the bag collar to insure a proper seal when the lter

housing is closed.

8. Screw the sump onto the cap and hand-tighten securely. Do not over-tighten.

Bag Replacement

Figure

Gauge

¼” Drain Plug

Spanner

3/8” NPT Drain Plug Ball Valve

PVC 3/8” x 3/8” FPT

Buna-N

¼” Gasket

Filter Housing

Basket Body

Replacement Bag

Filter Head

O-Ring

Installation Guide

Specications

Max. Pressure: 520 kPa

Maximum Temperature: 37.7°C ( 100°F)

Recommended Service Flow Rate: 21 kPad @ 132 Lpm

Maximum Service Flow Rate: 21 kPad @ 180 Lpm

Note: Where line pressure exceeds 500 kPa, an approved pressure limiting device must be installed to

comply with Australian & New Zealand Plumbing Standards.

Materials of Construction

Filter Cap: Polypropylene

Filter body 20-inch: Polypropylene

Basket 20-inch: Polypropylene

Gasket: Buna-N or EPR

0-ring (Sump): Buna-N

Vent Plug: Polypropylene

Drain Plug: Polyethylene

Drain Valve: PVC

Seals: Buna-N

Gauge: Brass & Bronze

Spanner Wrench: Polypropylene

Dimensions

Diameter: 180 mm (7¼”)

Height: 600 mm (24”)

Note: Allow extra 300 mm height for cartridge changes.

Specications

Troubleshooting

Leaks

1. Check the 0-ring for dirt, cuts, or swelling. Replace 0-ring if necessary.

2. Make sure housing is closed properly. Hand-tighten securely. Do not over-tighten.

3. Check all threaded connections and re-thread as needed.

4. Check to see if the lter bag is dirty and blinded over (see Warning under Bag Replacement). If

this is the case, replace bag according to instructions.

Poor Filtration Results

1. Check to make sure the lter bag is properly seated in the support basket (see Warning under

Bag Replacement). The bag should extend fully to the bottom of the basket and the top should

overlap the sealing collar.

2. Check for rips or tears in the lter bag.

Notes

The complete range of Puretec products are developed, rened and made to meet and exceed stringent

specications for the worldwide market.

Important Note: Sales of products are subject to our Terms & Conditions which are available upon

request. All specications, prices and photos are a guide only and are subject to change without notice.

Please ring to conrm details. Do not use products with microbiological unsafe water without adequate

disinfection. Under normal circumstances a pressure limiting valve is not required. If incoming water pressure

is excessive it may however be necessary to install an approved pressure limiting valve. Maximum ow

depends on cartridge, vessel, pressure, impurities etc.

Troubleshooting

Warranty

Warranty: Any claim under this warranty must be made within 3 years of the date of purchase of the

product. This product is warrantied to be free of defect of material and workmanship for 3 tears from date

of purchase.

Puretec is renowned for its quality and after-sales support so if you have any issues please call 1300 140

140 (AU) or 0800 130 140 (NZ). To make a warranty claim, contact us directly or the place of original

purchase. All costs relating to a warranty claim must be approved by Puretec prior to any work being carried

out.

3 year warranty is 1 year parts and labour, plus 2 years parts only. Puretec will pay your reasonable, direct

expenses of claiming under this warranty. You may submit details and proof of your expense claim to place

of purchase for consideration.

Warranty/Australia

This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road, Lonsdale SA 5160,

telephone no. 1300 140 140 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our goods come with

guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement

or refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Warranty/New Zealand

This warranty is given by Puretec Ltd, Reg. No 4464398, Po Box 875 Cambridge 3450 NZ, telephone no.

0800 130 140 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our goods come with

guarantees which cannot be excluded under the Australian Consumer Law. You are entitled to replacement

or refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

The warranty only applies if the product was used and/or installed in accordance with the user guide and/

or installation instructions. This warranty is given in lieu of all other express or implied warranties and

manufacturer shall in no circumstance be held liable for damages consequential or otherwise or delays

caused or faulty manufacturing except as excluded by law.

Applicable to all above, is that the Warranties need to be approved by Puretec to ensure product was not

incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s discretion,

including chargeable inspection and labour costs incurred.

Warranty

Inhaltsverzeichnis

Andere Puretec Wasserfiltersystem Handbücher

Puretec

Puretec WH1 Bedienungsanleitung

Puretec

Puretec Hybrid-R Triple Series Bedienungsanleitung

Puretec

Puretec Z1-RW-K Bedienungsanleitung

Puretec

Puretec Hybrid-M1 Bedienungsanleitung

Puretec

Puretec FP Series Bedienungsanleitung

Puretec

Puretec IMB Series Bedienungsanleitung

Puretec

Puretec 2CI-C Bedienungsanleitung

Puretec

Puretec FP Series Bedienungsanleitung

Puretec

Puretec UFC Series Bedienungsanleitung

Puretec

Puretec RO SERIES Bedienungsanleitung

Puretec

Puretec HYBRID H6 Bedienungsanleitung

Puretec

Puretec Z18 Bedienungsanleitung

Puretec

Puretec Sparq S4 Bedienungsanleitung

Puretec

Puretec TSI Series Bedienungsanleitung

Puretec

Puretec CFS 2CI Series Bedienungsanleitung

Puretec

Puretec CR-Z2 Bedienungsanleitung

Puretec

Puretec IF Series Bedienungsanleitung

Puretec

Puretec RO270 Bedienungsanleitung

Puretec

Puretec IL-UB Series Bedienungsanleitung

Puretec

Puretec RI-EPAS Bedienungsanleitung

Puretec

Puretec Hybrid-P9 Bedienungsanleitung

Puretec

Puretec Z1 Tripla Black Series Bedienungsanleitung

Puretec

Puretec NTR-E3 Series Bedienungsanleitung

Puretec

Puretec CO-I50 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung