Puretec MPB202 Bedienungsanleitung

BAG FILTER SYSTEM

USER GUIDE

For correct operation & installation it is

essential to observe these instructions.

Installation & operation manual

for Bag Filter Systems

MPB202

Filtaflo Customer ServicePuretec Customer Service

Thank you for purchasing a Puretec Bag Filter System. Your system is a patented, proven

performer manufactured from only quality materials and components and will give years of

clean, fresh, invigorating shower water free of impurities if maintained properly.

Caution: Do not use with water that is microbiologically unsafe or with water of unknown

quality without adequate disinfection before or after the system.

The system is designed for metropolitan supply water but can be used in other situations. For

other types of water supply please contact your local Puretec stockist.

The Puretec Bag Filter System cartridge needs replacing regularly to maintain optimum

performance. This is a simple procedure when following instructions. For cartridge replacements

contact your stockist.

Precautions

WARNING: For drinking water applications, do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION: Filter must be protected against freezing (when used with aqueous solutions), which

can cause cracking of the filter and water leakage.

CAUTION: Because of the product’s limited service life and to prevent costly repairs or possible

water damage, we strongly recommend that the bottom of all plastic housings be replaced every

ten years. If the bottom of your housing has been in use for longer than this period, it should be

replaced immediately. Date the bottom of any new or replacement housing to indicate the next

recommended replacement date.

Notes

• Make certain that installation complies with all state and local laws and regulations.

• Do not use wicking or sealer for fitting connections into the cap of the filter. Teflon® tape is

recommended for this purpose.

• Do not install where system will be exposed to direct sunlight.

• Allow a minimum of 3 inches clearance under the filter or optional sump stand to facilitate

filter changes.

BAG FILTER SYSTEM

USER GUIDE

Installation

1. Before installing, verify that the materials of construction of the Puretec Bag Filter System

are compatible with the fluid being filtered.

2. The location of the filter should include the following considerations:

(1) adequate space for ease of changing the filter bag,

(2) drainage or containment to collect drained or spilled liquid, and (3) proper ventilation, if

required.

3. When installing the system, include isolation valves for the filter and support for the filter

housing. Use caution when applying heat near the filter housing. It is best to weld or sweat

all fittings before assembly to the filter. The filter head may be mounted to the filter support

using 5/16 inch x 1¼ inch long bolts. The bolt spacing is 3 inch on center and the bolt circle is

2-1/8 inch.

4. The filter must be installed in the vertical position with the inlet/outlet ports at the top. Flow

through the housing is inline. Note the inlet and outlet ports when connecting piping.

5. The filter housing is equipped with a ¼ inch NPT gauge part an the outlet for installation

of a pressure gauge (included) and a 3/8 inch NPT drain port at the base of the sump (3/8

inch NPT ball valve supplied). The gauge or valve should be installed using Teflon® tape as a

thread sealant.

Bag Selection

The Puretec Bag Filter Housing is designed for use with Puretec filter bags. Filter bags are

available in 1, 5, 10, 25, 50, 100 and 200 micron. Polypropylene is the standard bag material but

nylon is available upon request.

Start-up

1. Open the inlet valve. It is recommended that the inlet valve be opened before the outlet valve

to prevent any backflow.

2. Vent trapped air from the system before opening the outlet valve.

3. Open the outlet valve.

User Guide

BAG FILTER SYSTEM

USER GUIDE

Bag Replacement

The pressure differential across the bag will remain fairly constant until the bag is approximately

80% blinded off. It is recommended that the bag be changed when the pressure differential

reaches 15 psi. However, this figure can vary with the type of filter bag. The bag manufacturer’s

data should be consulted to determine the actual pressure drop for replacement.

WARNING: Review all precautions specific to the handling of the fluid being filtered before

changing the filter bag. A filter bag that has been .used with a hazardous liquid may contain

residual amounts of this material and should be handled with the same safeguards that

would be used in handling any hazardous and/or toxic material i.e. gloves, respirators,

protective eyewear, etc. Filter bags should be disposed of in accordance with federat state or

local laws and requirements. Failure to follow precautions may result in injury.

l. Close isolation valves to the filter.

2. Drain sump. (See WARNING above)

NOTE: If bag has not been changed on a timely basis it may not drain. If necessary, the liquid

contents of the used bag can be poured into the replacement bag to be filtered.

3. Unscrew sump from cap. Sump will unscrew counterclockwise.

CAUTION: Support sump at base while unscrewing to prevent dropping and possibly

damaging the sump or drain valve.

4. Remove basket assembly from sump. (See WARNING above)

5. Remove bag from basket.

6. Remove 0-ring from groove in the sump and wipe groove and 0-ring clean. Relubricate 0-ring

with food grade silicone lubricant or similar. Insert 0-ring in place and press into groove.

NOTE: This step is important to ensure a proper housing seal. Make certain the 0-ring is

seated level in the groove.

7 Insert new bag into the basket. Form the bag to the contours of the basket_ making sure that

the bag extends fully to the bottom of the basket.

NOTE: Make sure the filter bag overlaps the bag collar to insure a proper seal when the filter

housing is closed.

8. Screw the sump onto the cap and hand-tighten securely. Do not over-tighten.

BAG FILTER SYSTEM

USER GUIDE

Figure 1

User Guide

BAG FILTER SYSTEM

USER GUIDE

Gauge

¼” Drain Plug

Spanner

3/8” NPT Drain Plug Ball Valve

PVC 3/8” x 3/8” FPT

Buna-N

¼” Gasket

Filter Housing

Basket Body

Replacement Bag

Filter Head

O-ring

User Guide

Specifications

Max. Pressure: 630 kPa (90 psi)

Maximum Temperature: 37.7°C ( 100°F)

Recommended Service Flow Rate: 21 kPad (3 psid) @ 132 Lpm (35 gpm)

Maximum Service Flow Rate: 21 kPad (3 psid) @ 188 Lpm (50 gpm)

Materials of. Construction

Filter cap Polypropylene

Filter body 10-inch Polypropylene

Filter body 20-inch Polypropylene

Basket to-inch Polypropylene

Basket 20-inch Polypropylene

Gasket Buna-N or EPR

0-ring (Sump) Buna-N

Vent plug Polypropylene

Drain plug Polyethylene

Drain valve PVC

Seals Buna-N

Gauge Brass & Bronze

Spanner wrench Polypropylene

Dimensions

Diameter: 180mm (7¼”)

Height: 600mm (24”)

Note: Allow extra 300mm height for cartridge changes.

BAG FILTER SYSTEM

USER GUIDE

Troubleshooting

LEAKS

l. Check the 0-ring for dirt, cuts, or swelling.

Replace 0-ring if necessary.

2. Make sure housing is closed properly. Hand-tighten securely. Do not over-tighten.

3. Check all threaded connections and rethread as needed.

4. Check to see if the filter bag is dirty and blinded over.

(See WARNING under Bag Replacement) If this is the case, replace bag according to

instructions.

POOR FILTRATION RESULTS

l. Check to make sure the filter bag is properly seated in the support basket. (See WARNING

under Bag Replacement) The bag should extend fully to the bottom of the basket and the top

should overlap the sealing collar.

2. Check for rips or tears in the filter bag.

NOTES

FPS designs, manufactures and supports Puretec water care products, the name you can trust for

viable and proven water solutions. All pictures and information are supplied as a guide only.

The complete range of Puretec products are developed, refined and made to meet and exceed stringent

specifications for the worldwide market.

Important Note: Sales of products are subject to our Terms & Conditions which are available upon

request. All specifications, prices and photos are a guide only and are subject to change without

notice. Please ring to confirm details. Do not use products with microbiological unsafe water without

adequate disinfection. Where water pressur eexceeds maximum pressure specifications, a pressure

limiting valve must be fitted. Maximum flow depends on cartridge, vessel, pressure, impurities etc.

BAG FILTER SYSTEM

USER GUIDE

WARRANTY

WARRANTY: Any claim under this warranty must be made within 36 MONTHS of the date of purchase

of the product. This product is warrantied to be free of defect of material and workmanship for 36

months from date of purchase. To make a claim under the warranty, take the product and proof of

purchase to place where you purchased the product, and they will lodge a Warranty Request with

Puretec.

Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may submit

details and proof of your expense claim to place of purchase for consideration.

This warranty is given by Puretec, ABN 66 474 243 571, 14-16 Bailey Street, St Marys SA 5064,

telephone no. 1300 190 190 and email at [email protected].

This warranty is provided in addition to other rights and remedies you have under law: Our goods

come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled

to replacement or refund for a major failure and to compensation for other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure.

The warranty only applies if the product was used and/or installed in accordance with the user guide

and/or installation instructions. This warranty is given in lieu of all other express or implied warranties

and manufacturer shall in no circumstance be held liable for damages consequential or otherwise or

delays caused or faulty manufacturing except as excluded by law.

Applicable to all above, is that the Warranties need to be approved by Puretec to ensure product

was not incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s

discretion, including chargeable inspection and labour costs incurred.

Customer Service Helpline 1300 190 190

Email [email protected]

Web www.puretec.com.au

BAG FILTER SYSTEM

USER GUIDE

Inhaltsverzeichnis

Andere Puretec Wasserfiltersystem Handbücher

Puretec

Puretec Z1 Tripla Black Series Bedienungsanleitung

Puretec

Puretec Z18 Bedienungsanleitung

Puretec

Puretec CO-RO270 Series Bedienungsanleitung

Puretec

Puretec PureMix Z6 Bedienungsanleitung

Puretec

Puretec PRO270 Bedienungsanleitung

Puretec

Puretec PureMix Z2 Bedienungsanleitung

Puretec

Puretec Basic HD Series Bedienungsanleitung

Puretec

Puretec CFS 2CI Series Bedienungsanleitung

Puretec

Puretec TSI Series Bedienungsanleitung

Puretec

Puretec UFC Series Bedienungsanleitung

Puretec

Puretec NTS Series Bedienungsanleitung

Puretec

Puretec X3 Bedienungsanleitung

Puretec

Puretec CO-I50 Bedienungsanleitung

Puretec

Puretec PureMix X7 Bedienungsanleitung

Puretec

Puretec FilterWall IM2 Series Bedienungsanleitung

Puretec

Puretec CR-Z2 Bedienungsanleitung

Puretec

Puretec Hybrid-R Triple Series Bedienungsanleitung

Puretec

Puretec Multitrol MUL-E3 Series Bedienungsanleitung

Puretec

Puretec CD Series Bedienungsanleitung

Puretec

Puretec RO270 Bedienungsanleitung

Puretec

Puretec HybridPlus Series Bedienungsanleitung

Puretec

Puretec 2CI-C Bedienungsanleitung

Puretec

Puretec QT12 Bedienungsanleitung

Puretec

Puretec Hybrid-P9 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung