Pyle Pro PMX402M Bedienungsanleitung

Owner’s Manual

PMX402M 4 CHANNELS

PMX602M 6 CHANNELS

PMX802M 8 CHANNELS

www.pyleaudio.com

_________________________________________________________- 2 -_________________________________________________

FEATURES

Balanced microphone inputs, high impedance microphone/line Inputs and

Tape/CD inputs. All may be used simultaneously reverb built in with individual control

on each channel line out for connection to external amplifiers record out jack for taping

performances R.F interference protection on all inputs and outputs.

The family of products built-in high-quality, high-effect of MP3 players can play in

the USB disk MP3 format songs. Blue backlit LCD display screen can display the total

number of songs in the USB disk, songs of the total play time ,play time at present, play

/ stop sign, symbol cycle, as well as the EQ. Through four key touch with LCD display

is easy to operate MP3 player.

SAFETY INSTRUCTIONS

CAUTION: To reduce the risk of electrical shock, do not

remove the cover (or back). No user serviceable parts

inside; refer servicing to qualified personnel.

WARNING: To reduce the risk of fire or electrical shock, do not

expose this appliance to rain or moisture.

This symbol, wherever it appears,

alerts you to the presence of

uninsulated dangerous voltage

inside the enclosure-voltage that

may be sufficient to constitute a

risk of shock.

This symbol, wherever it appears,

alerts you to important operating

and maintenance instructions in

the accompanying literature. Read

the manual.

_________________________________________________________- 3 -_________________________________________________

A. FRONT PANEL SECTION FEATURES

1. BALANCE INPUT (MIC)

Electronic Balanced inputs acceptable a standard XLR male connector. It is designed to accept a

balanced low impedance input signal, Phantom power (15 volts) for condenser microphones is always

on and available. It has an input impedance of 1K ohm. The connector is wired as: Pin= shield ;

Pin3= negative(cold).

2. BALANCE INPUT(LINE)

Electronic Balanced inputs acceptable a standard 1/4＂jacks connector. It is designed to accept a

balanced high impedance input signal (This use for connection Deck , Turntable, Keyboard etc…).

3. VOLUME

This is function to adjust the volume of signal connection into each channel and adjust the

volume of output, together with master fader.

4. TREBLE

This control gives you up to 15 db of boost or cut at 10 kHz and above, and it is also flat at the

detent. Use it to add sizzle to cymbals, and an overall sense of transparency or edge to key-boards,

vocals, guitar, and bacon frying. Turn it down a little to reduce sibilance, or to hide tape hiss.

5. LOW FREQUENCY

This control gives you up to 15 dB boost or cut at 100Hz and below. This circuit is flat (no boost

or cut) at the center detent position. This frequency represents the punch in bass drums, bass guitar, fat

synch patches, and some really serious male singers.

6. REVERB DEPTH/EFFECT BALANCE

This is a send control to the reverb buss, It controls the amount of reverberation added to the

Input signals.

_________________________________________________________- 4 -_________________________________________________

7. GRAPHIC EQUALIZER

2×5-band equalizer is provided for tone control over each frequency , and for precise high

quality sound by final tone control. It can control main channel and record

channel.( 60,250,1K,2K,8KHz ) shelving at +/-12dB.

8. LCD DISPLAY(There are three states show)

a. Machine became the first LCD display screen information are the trademarks of

products, USB version, and initial system.

b. The second message is to remind the screen insert USB disk, or disk is not MP3

format.

c. The third message is the total number of songs in the USB disk, songs of the total

play time ,play time at present, play/pause/ stop sign, symbol cycle, File Format(M

refers to the MP3 file format, W refers to the WMA file format), as well as the EQ.

9. TOUCH BUTTON

Four touch keys, which are single cycle / circle of the total, up , play /pause / stop,

down, EQ option. All of the touch button of this machine are conventional key and

compound key.

a. Symbol cycle (A total of 6 cycle model) they are All cycle , random play ,song cycle ,

End the end of the single player , cycle by a player and players here. Through the

button to switch modes, according to a time switch, LCD display the logo.

b. Down This is a complex bond, In the state of play, press the button, Will play on a

song; In the state to suspend or stop, press the button, the current song will be

re-broadcast; Press the button for a long time, can adjust the LCD backlight

brightness.

c. Play /Pause/ Stop This is a Multi-Function control, the press is a player, next it is

time to pause, then it is stop, while the corresponding LCD display signs. Press for a

long time, null and void.

_________________________________________________________- 5 -_________________________________________________

d. Up This is a multi-function control, In the state of play, press the button,

Will play the next song; Press the button for a long time, can adjust the LCD

backlight brightness.

e. EQ This is a conventional keys, press the first choice of a EQ, a total of 11 EQ, are

Natural, Rock, Pop, Class, Jazz, Blue, Hall, Bass, Soft, Country, and Opera.

10.POWER LED

It lights when power switch turn on.

11. PHANTOM LED

The LED +15V will be turned on when start working.

12. PHANTOM POWER SWITCH

When it is depressed, the XLR jack input has +15V voltage.

13. OUTPUTS LEVEL INDICATOR

This is level meter which shows output levels of left & right channel condition on the way of

operation, therefore, you can see output condition thru this master level indication.

.14. MASTER VOLUME

Using by this control, you can adjust signal level of main channel.

15. TAPE

This controls the level of the playback inputs(RCA) jack.

16. USB DISK

USB disk insert jack.

17. MP3

Using by this control, you can adjust MP3 signal level send to main channel.

18. REVERB EFFECTS DELAY

Using by this control, you can adjust the delay time interval of echo repeat.

19. REVERB EFFECTS REPEAT

Using by this control , you can adjust reverberating deepness.

20. REVERB EFFECTS LEVEL

Using by this control, you can adjust signal level of echo output.

_________________________________________________________- 6 -_________________________________________________

B. BACK PANEL SECTION FEATURES

1. SPEAKER JACK (LEFT/RIGHT)

These are 2 conductor 1/4” speaker outputs. Each one is rated at 8 ohm minimum impedance.

Total minimum load for the amplifier is 4 ohms. You may connect either 1-4 ohm. 1-8 ohm or 2-8

ohm speaker cabinets. Do not below rated minimum impedance.

2. SEND/RETURN

Using by this jack, you can use stereo 1/4＂jacks connector send internal signal which before

power amplifier to external effects processing, after processing return to internal power amplifier.

Or you can use stereo or mono 1/4＂jacks connector send external signal to inner power amplifier .

3.TAPE INPUT

These RCA jacks are for brining in a tape deck, CD play or other line level source. The

impedance is 10k ohms .

4. REC OUTPUT

These RCA jacks are for hooking up a tape desk to record from the mixer. Both channel are

summed into mono for compatibility. The signals are taken pre-master section, meaning that they are

without reverb or the master tone section, and does not include the Tape in signal, The impedance is

1K ohms @ -10dBv.

5. FAN

In order to prevent rising the inside temperature, the inside heat is emitted outside.

6. POWER SWITCH

When you want to operate, turn on it, then the LED will be turned on .

_________________________________________________________- 7 -_________________________________________________

7. CHANGE-OVER SWITCH

This device is used to 110V/220V or 115V/230V voltage conversion.

8. AC POWER CORD/FUSE HOLDERS

AC 220～240V 60Hz or 110-120V 60Hz ,Check the power voltage of supply with silk-screen of

the panel before connections. When occur a problem on this appliance, the fuse will be cut off, power

to prevent form a problem.

C. CONNECTIONS

You will need a lot of cables for different purposes – see the following figures to make sure you

have got the right ones. Unbalanced equipment may be connected to balanced inputs/outputs. Either

use mono 1/4＂jacks or connect ring and sleeve of TRS jacks.

Fig. 5: Balance plug

_________________________________________________________- 8 -_________________________________________________

Bandwidth 20Hzto20kHz_+1dB

InputImpedance: Lo-ZMic 1Kohms

Hi-ZMic/Line 33Kohms

Tape playback 10Kohms

Inputlevel: Lo-ZMic -50dB

Hi-ZMic/Line -20dB

Tapeplayback -10dB

Recoutputlevel +22dB(max)

MODEL NO PMX402M PMX602M PMX802M

CHANNELS 4CHANNELS 6CHANNELS 8CHANNELS

POWER 400W 600W 800W

DIMENSION 15.75’X12.01’X7.87’ 17.32’X12.01’X7.87’ 20.28X12.01’X7.87’

Specifications:

*With USB 2.0 Terminal and LCD

*5-Band graphic equalizer

*Each channel tone control

*Effect control

*TAPE input, REC output

*Channel tone adjust (high/low+/-15dB)

*AUX/TAPE/effect feedback input

*Effect send

*Master volume control

*Phantom + 15V

Power supply 110VAC 60HZ，SWITCHABLE 220VAC 50HZ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Pyle Pro Verstärker Handbücher

Pyle Pro

Pyle Pro PYLE PRO PTA2 Bedienungsanleitung

Pyle Pro

Pyle Pro PPA200 Bedienungsanleitung

Pyle Pro

Pyle Pro PCMX260MB Bedienungsanleitung

Pyle Pro

Pyle Pro PT610 Bedienungsanleitung

Pyle Pro

Pyle Pro Waisband Amplifier PWMA30 Bedienungsanleitung

Pyle Pro

Pyle Pro PEA4000 Bedienungsanleitung

Pyle Pro

Pyle Pro PQ1000 Bedienungsanleitung

Pyle Pro

Pyle Pro PMX601 Bedienungsanleitung

Pyle Pro

Pyle Pro P1501ATU Bedienungsanleitung

Pyle Pro

Pyle Pro P2002ABTI Bedienungsanleitung

Pyle Pro

Pyle Pro PTAU34 Bedienungsanleitung

Pyle Pro

Pyle Pro PT-600A Bedienungsanleitung

Pyle Pro

Pyle Pro PT110 Bedienungsanleitung

Pyle Pro

Pyle Pro PZR1000 Bedienungsanleitung

Pyle Pro

Pyle Pro PEXA3000 Bedienungsanleitung

Pyle Pro

Pyle Pro PTAU45 Bedienungsanleitung

Pyle Pro

Pyle Pro PWMA600 Bedienungsanleitung

Pyle Pro

Pyle Pro PT4000 Bedienungsanleitung

Pyle Pro

Pyle Pro PCAU48BT Bedienungsanleitung

Pyle Pro

Pyle Pro PT-2400 Bedienungsanleitung

Pyle Pro

Pyle Pro PWMA3600 Bedienungsanleitung

Pyle Pro

Pyle Pro PPA140 Bedienungsanleitung

Pyle Pro

Pyle Pro PTA1 Bedienungsanleitung

Pyle Pro

Pyle Pro PMX804 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung