Pyle PT110 Bedienungsanleitung

80WattAC/DCMicrophone

PAMonoAmplifierwithUSB/SD/FM/BT

PT110

LED Level Display w/ 70V Output & Mic Talkover

www.PyleUSA.com

INTRODUCTION

Your New PYLE PT110 PA AMPLIFIER gives you the power and versatility you

need in a professional sound system. The amplier's wide frequency response

makes it suitable for amplifying music or vocal program material. It can be used

for live bands, oce paging systems, public announcements, or a variety of

other installations. Please read this manual throughly before you attempt to

set up and use the amplier. It contains a range of installation suggestions as

well as instructions to ensure safe usage. Installed properly, you can expect

years of trouble-free service from this product.

FEATURES AND CONTROLS

FRONT PANEL

REAR PANEL

1. POWER SWITCH: Press to switch the power unit ON or OFF.

2. Phone Jack: Connect a pair of stereo headphones for private listening or

cueing (monitoring) sound prior to “airing”it.

3 8 5 67

910 11

15 1816

19 21

www.PyleUSA.com 3

3. MIC 1 & MIC 2 Jack: Allows you to connect up to two 6.35mm type microphone.

4. LED Level Display Meter

5. MIC Volume Control: Lets you adjust the MIC1/MIC2 sound level.

6. Three Input Sources Mixing Controls: Controls the sound level for each of the

audio input sources.

PHONO/AUX: Select and connect an alternative high level (AUX/CD) or low level

(PHONO) audio sound source.

7. 100 Hz, 1 kHz, & 8 kHz Equalizer Controls: To enhance the sound or tailor the

high, midrange, and low frequencies for each audio source input to the acoustics

of a particular performance environment, you can adjust these equalizer tone

controls.

8. AUX Input Jack: Allows you to connect any high level sound source, such as a

CD player, tape deck, or tuner, to the CD/AUX jack.

9. CONTROL PANEL BUTTON

A. These buttons are only used to control the USB/SD, Wireless BT and FM

functions and doesn’t control other functions.

B. MODE BUTTON: Press this button to select one from USB/SD mode, FM mode

or Wireless BT play mode. USB/SD mode will be set automatically after turning

ON the unit. Automatically plays mp3 les after inserting a USB ash drive or

SD card. You cannot select AUX, CD and DVD input on this button.

C. Each press of the PLAY/PAUSE BUTTON causes the operation to change from

play to pause or from pause to play in the USB/SD mode or Wireless BT mode.

Press the PLAY/PAUSE BUTTON one time to auto scan all frequencies from

87.5MHz to 108MHz in FM mode Press the button to auto scan channels when

you use FM radio for the rst time. After stop searching, the unit will auto

store all the radio channels and play from the rst radio channel. You don't

need to rescanevery FM radio start up.

D. PREV and NEXT BUTTON: Use these two buttons to select previous or next

track, depending on these dierent modes as below.

• In USB/SD mode: Use to select previous or next track.

• In Wireless BT mode: Use to select previous or next track.

• In FM mode: Use to select previous or next radio channel.

10. LED Display: Show MP3/SD/BT/FM information.

11. USB Port and SD card socket: After inserting a USB ash drive/SD Card into

the input terminal, then press the mode button to choose between audio from

the USB port, SD Card input, Wireless BT or FM radio. If you want to use the

Wireless BT, check the below steps.

www.PyleUSA.com

STEPS FOR CONNECTING WITH WIRELESS BT DEVICE

A. Press MODE button under the ID3 display screen and enter into BT mode.

B. Search for the Wireless BT device and nd the BT name“PYLEUSA or BT”

C. Select the PYLEUSA or BT Wireless BT name and wait for the device to pair.

D. The unit will make a sound conrming that the devices have successfully paired.

E. Once paired you can play music from your bt device. You can also use the control

buttons on the unit to select the tracks from your bluetooth device.

12. Voltage Switch: The amplier has selectable input voltage from 110V/60Hz

which is the standard in USA and CANADA. You can also switch the input

voltage to 220V/50Hz for EUROPEAN operation. Please make sure the switch is

in the proper position before operating, otherwise severe damage will result

not cover by the warranty. Please also replace the fuse with proper rating in

this situation (see the SPECIFICATIONS for the fuse rating).

13. GND (GROUND) screw terminal: If you connect a low level audio input source

(turntable) to the PHONO, please connect your turntable's ground wire (usually

black or green) to the amplier’s GND terminal, to avoid a low frequency hum.

You can also use this screw to ground any other system connection.

14. Unswitched AC Accessory Outlet - 300W MAX.

15. PHONO Input Jack: You can connect a low level audio input source, such as a

magnetic cartridge turntable to the L PHONO and R PHONO jacks.

16. AUX/CD Input Jack: Allows you to connect any high level sound source, such

as a CD player, tape deck, or tuner, to the CD/AUX jack.

17. PHONO and AUX/CD Input Selector: Lets you select the input source you

want to connect to the amplier.

18. MIX BUS Jack: Allows you to connect another units to this jack to double the

size of your PA system.

19. Push-Terminal Connectors: Let you easily connect speaker wires directly to

the ampliers.

20. Wireless BT Anntena: Pull the antenna out when using Wireless BT input.

21. FM Anntena: Pull the the antenna when using FM input.

22. DC 4A/12V Input Jack: Allows you to connect the power for amplier from

12-volt battery source.

INSTALLATION GUIDELINES

• Input connections

• The Unit accept a board range of input sources, including:

Microphones (up to two simultaneously)

• Compact Disc (CD) player

• Cassette, Reel-to-Reel or other tape player Radio Tuner

• Magnetic Cartridge Turntable

www.PyleUSA.com 5

Connecting Microphones

The MIC 1 and MIC 2 jacks permit you

to connect two microphones with

6.35mm plug.

Connecting a CD or Tape Player, or

Tuner

In this Situation, set the PHONO and

AUX/CD SELECTOR switch to the AUX/CD

Connecting a Turntable

In this Situation, set the PHONO and

AUX/ CD SELECTOR switch to the

PHONO.

Speaker Connections

One or more speakers (4, 8, or 16-Ohm)

speakers can be connected to the

amplier with or without transformers.

However, before you connect any speaker

to the amplier, the total speaker impe-

dance must be calculated in order to

avoid damage to the amplier.

A total speaker impedance greater than

16 Ohms or less than 4 Ohms can be

cause this damage to occur. To begin

with, in order to ensure equal volume

from each speaker, all connected

speakers should have the same impe-

dance. A proper total impedance with

the 4 to 16 Ohms range can be achieved

by combining series and paralled

speaker connections. Please see the

diagrams which follow the same impe-

dance. Finally, always use the shortest

length of speaker wire possible of proper

gauge. Usually, 18-gauge wire is ade-

quate for lengths under 25 feet, while

16-gauge is used for greater lengths.

System 1: Single speaker system

1. Connect the speaker (-) terminal to

the amplier COMMON terminal

2. Depending on the speaker being

used, connect the speaker (+)

terminal to the amplier's 4-Ohm, 8-

Ohm or 16-Ohm amplier terminal.

mic 1

mic 2

Set the switch to AUX/CD

position

CD, Tape player or Tuner R

Set the switch to PHONO

position

Turntable

This example shows a 4 Ohm Speaker

www.PyleUSA.com

System 2: Two (or more) speakers in

series

1. Connect the LEFT SPEAKER (-) to the

amplier COMMON terminal.

2. Connect the LEFT SPEAKER (+) to the

RIGHT SPEAKER (-).

3. Connect the RIGHT SPEAKER (+) to the

amplier's 4-Ohm, 8-Ohm, or 16-Ohm

terminal, depending on the TOTAL

IMPEDANCE of the two speakers.

If each speaker has an impedance of

8 Ohms, the total speaker impedance

in this series conguration is 16 Ohms.

NOTE:

ADDITIONAL SPEAKERS MAY BE

INCLUDED IN SERIES, BUT IT IS NECES-

SARY TO CALCULATE TOTAL IMPE-

DANCE, AND CONNECT THE SPEAKER

CIRCUIT TO A TERMINAL OF APPRO-

PRIATE IMPEDANCE. FOR EXAMPLE, IF

THREE SPEAKERS OF 4-OHM ARE

USED, TOAL IMPEDANCE IS 12 OHMS,

YOU SHOULD CONNECT TO THE

16-OHM TERMINAL.

System 3: Two (or more) speakers in

parallel

1. Connect the LEFT SPEAKER (-) to the

RIGHT SPEAKER (-).

2. Connect BOTH the LEFT SPEAKER (-)

and the RIGHT SPEAKER (-) to the

amplier COMMON terminal.

3. Connect the LEFT SPEAKER (+) to the

RIGHT SPEAKER (+).

4. Connect BOTH the LEFT SPEAKER (+)

and RIGHT SPEAKER (+) to the

amplier 4-Ohm, 8-Ohm or 16-Ohm

terminal, depending on the TOTAL

IMPEDANCE of the two speakers.

If each speaker has an impedance of

8-Ohm, the total speaker impedance

in this parellel conguration is 4 Ohms.

System 4: Four speakers in series/

parallel combination

1. Group the four speakers into two pairs.

2. Connect each pair of speakers in

SERIES (see system 2 above). If you

connect 8-ohm speakers, the total

impedance of each pair is 16 ohms.

Right Speaker

Left Speaker

This example shows a two 4 Ohm Speakers,

the total impedance is 8 ohms.

Right Speaker

Left Speaker

This example shows a two 8 Ohm Speakers,

the total impedance is 4 ohms.

www.PyleUSA.com 7

3. Connect the two pairs of speakers in PARALLEL. If you connect 8-ohm speakers,

the total impedance of both pairs is 8 ohms.

Note:

If each of the four speakers is 8 ohms, the total speaker impedance of the combined

series/parallel connection described above is also 8 ohms. Likewise, the total

speaker impedance is 4 or 16 ohms, if the speakers are 4 or 16 ohms respectively.

4. Connect the speakers' (-) terminals to the amplier's COMMON terminal.

5. Connect the speakers' (+) terminals to the amplier's 4-Ohm, 8-Ohm, or 16-Ohm

terminal, depending on the TOTAL IMPEDANCE of the FOUR SPEAKERS.

See the chart below for some samples system suggestions:

This example shows four 8 Ohm

Speakers, the total impedance is

8 ohms.

www.PyleUSA.com

SERIES/PARALLEL VARIATIONS

Although the description above is for combining TWO SERIES PAIRS in a PARALLEL

hook up, you may also select to combine a SERIES PAIR and a PARALLEL PAIR in a

PARALLEL hook up. Simply be sure you have properly calculated the total impe-

dance, and connect the (+) speaker circuit wire to the proper amp terminal.

For example, if you use a SERIES PAIR of 8-Ohms speakers (the total impedance is

16 ohms) and a PARALLEL PAIR of 8-Ohms speakers (the total impedance is 4 ohms)

in a PARALLEL hook up, the TOTAL IMPEDANCE of this system is 3.2 OHMS, so you

should connect the (+) speaker circuit wire to the 4-OHM terminal.

See the chart below for some samples system suggestions:

COMBINATION OF ONE SERIES PAIR AND ONE PARALLEL PAIR IN PARALLEL

Four 8 Ohm

Speakers

www.PyleUSA.com 9

This example shows for the rst three systems in chart. In this case, 4-Ohm terminal

is used your system impedance may be varied depending on the impedances of

the individual speakers, and may reguire hook up to the 8 or 16 Ohms terminal.

System 5: Connecting speakers with transformers

1. Locate the input taps on your transformer. These taps are on side of the trans-

former, and are rated in watts, 10, 5, 2.5, 1.25 or 0.62. Usually, each speaker in a

system uses the same wattage tap. Connect the selected tap to the amplier

70V RMS terminal. If you wish a particular speaker to have a higher volume level,

connect the wire from 70V RMS to a higher wattage tap on the transformer.

2. Connect the transformer's COMMON tap on the primary side to the amplier

COMMON terminal.

3. Connect the speaker's (+) terminals to the transformer's secondary tap that

matches the speaker's TOTAL IMPEDANCE. Locate on the opposite side of the

transformer, these secondary taps are outputs, and are rated in Ohms 4, 8 or 16.

4. Connect the speaker's (-) terminals to the transformer's COMMON tap on the

secondary side.

NOTE:

• Before connecting the speakers, please be sure the total wattage of the primary

tap you use does not exceed the amplier's maximum power rating, PT110 20W

and PT210 40W.

• Avoid, where possible, multiple connections to the 70V RMS and COMMON

terminals.

4 Ohm 10w

Speaker

0.62

1.25

2.5

com

(watts)

com

(ohms)

www.PyleUSA.com

Using Headphones

To listen privately, or to monitor sound sources, connect a pair of low impedance

stereo headphones (not supplied) with 6.35mm plug into the PHONES jack on the

amplier front panel.

Please listen safely. Follow these recommendations:

Do not listen at extremely high volume levels. Extended, high-volume listening

can lead to permanent hearing loss. Always start with the volume control set to a

LOW level BEFORE you put the headphones on. Then gradually increase the volume

as necessary.

Connecting to standard AC power

After making all other connections, set the POWER switch to OFF position. Then

connect the power cord to a standard AC outlet.

Connecting to 4A/12V DC power

You can power the amplier from your vehicle's 12-volt battery. Connect the supplied

DC power cable's barrel plug to DC 12V IN jack on the amplier, and then connect

the cable's other end to the 12-volt accessory socket on the vehicle, such as the

cigarette-lighter socket.

CAUTIONS:

PLEASE UNPLUG THE AC POWER CORD BEFORE CONNECTING THE DC POWER

CABLE FOR THIS 12V POWER USAGE, AND DISCONNECT THE DC POWER CABLE

BEFORE PLUGGING IN THE AC POWER CORD FOR AC POWER USAGE.

THE VEHICLE USING THIS POWER SOURCE MUST HAVE A NEGATIVE GROUND

ELECTRICAL SYSTEM. IF YOU ARE NOT SURE OF IT, PLEASE CHECK WITH YOUR

VEHICLE'S DEALER.

Turning the amplier ON

1. Turn on the audio input source equipment which is connected to the amplier

INPUT jack.

2. Set all volume levels (MASTER, MIC 1, MIC 2, and PHONO/AUX) to their minimum

level settings.

3. Press the power switch to turn the amplier on.

Inhaltsverzeichnis

Andere Pyle Verstärker Handbücher

Pyle

Pyle Mini Blue PFA330BT Bedienungsanleitung

Pyle

Pyle PTA42BT Bedienungsanleitung

Pyle

Pyle PT250BA Bedienungsanleitung

Pyle

Pyle PDSB15A Bedienungsanleitung

Pyle

Pyle PT506BT Bedienungsanleitung

Pyle

Pyle PMX401 Bedienungsanleitung

Pyle

Pyle PLMRA200 Bedienungsanleitung

Pyle

Pyle PAMP1000 Bedienungsanleitung

Pyle

Pyle PT8050CH Bedienungsanleitung

Pyle

Pyle PHE1AW Bedienungsanleitung

Pyle

Pyle PDA7BU Bedienungsanleitung

Pyle

Pyle PTA66BT Bedienungsanleitung

Pyle

Pyle PCAU25A Bedienungsanleitung

Pyle

Pyle Hydra PLMRMP2A Bedienungsanleitung

Pyle

Pyle PLBA330FRD Bedienungsanleitung

Pyle

Pyle PWMA-840 Bedienungsanleitung

Pyle

Pyle Hydra PLMRMP2A Bedienungsanleitung

Pyle

Pyle Dryver PLAD212 Bedienungsanleitung

Pyle

Pyle PT506BT Bedienungsanleitung

Pyle

Pyle PEXA8500 Bedienungsanleitung

Pyle

Pyle PUKTEAK74 Bedienungsanleitung

Pyle

Pyle PTA44BT Bedienungsanleitung

Pyle

Pyle PCM30A Bedienungsanleitung

Pyle

Pyle P3201BT Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung

Phonic

Phonic XP 3000 Bedienungsanleitung