Pyle PLMR51B Bedienungsanleitung
AM/FM/MP3/USB/AUX Stereo Receiver,Single DIN,
30 Preset Memory Stations,LCD Display
PLMR51B
with Remote Control(Black)
Car MP3 player
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation kit
before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring
then pull it out to remove it.
2. Insert the two bracket keys into the left and right side of
the chassis to separate the chassis from the housing.
3. Install the mounting knob on the board. Check the
opening size of the sliding panel to be mounted. If the
measurement is not large enough, carefully cut it until it
slips easily on the opening. Do not force the handle in the
opening so as not to bend it. Locate the series of dubbing
tabs above, below and all sides to be mounted. Completely
insert it to the opening of the board, bend the tabs as
necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that
the wires behind are tucked and not pinched.
5. Follow the wiring diagram carefully.
Verify you’ve connected them correctly.
CAUTION! Connect the unit to a 12 Volt power source
with adequate ground.
6. Now that your wires are all completed, attach the front
panel and turn ON the unit (the vehicle must be switched on). If the unit does not
work, check the calibration again until the problem is solved. With the new car
stereo secured into the bracket, all you need to do is plug the wiring harness back
into the stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind are
tucked and not pinched. Sometimes this may take a few times when the vehicle
has a tight dash opening. Tuck the wires back into an opening behind the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that all
screws and trim pieces are securely in place.Try out the new stereo. Turn the car
power on again and play around with the stereo and its settings to be sure
everything is in working order.
15A
Front RCA Output(Left) Front RCA Output(Right)
Rear RCA Output(Left)
Rear RCA Output(Right)
EXternal MIC
SWC
HANDS FREE PUSH-TO-TALK
PUSH-TO-TALK
• Allows you to access SIRI or GOOGLE voice via Wireless BT.
• Your phone must support SIRI or GOOGLE voice. Once connected to BT, your phone will ask for access
to your contact list.
• Now you are ready to use PUSH-TO-TALK. Press the PUSH-TO-TALK icon.
You are ready to talk. Call "(CONTACT NAME)" The system will call without
having to use your phone.
WIRING CONNECTIONS
CONTROL PANEL BUTTONS
ANT:RADIO ANTENNA JACK
F-L:Front RCA Output(Left)
F-R:Front RCA Output(Right)
R-L:Rear RCA Output(Left)
R-R:Rear RCA Output(Right)
Power/speaker Connector
FUSE 15A
PRECAUTION
+12V DC
NEGATIVE
EARTH
CONTROL PANEL BUTTONS
1. (Power)/Mode(source) button
2. SEL (select/menu) button and VOL (volume) knob
3. Back to the previous conguration point
Pess /Bass enhances the pulse function
4. Short press button display clock in all mode. In USB mode, Short
press to select All info/Elapsed time/File info/Track info/clock operation.
Long Press button turn o illumination on panel and touch any button
to turn on illumination.
5. Folder up
6. Folder down
7. RPT (repeat), button 3 preset
8. RDM (random), button 4 preset
9. (pause/start), preset station 5 button
10. INT (intro) , preset button 6 station
11.Long Press BND button to activate SIRI. Short press BND
button to change band. Short press BND button to pick up/cut o
phone call.
12. (tune back, search back, crawl back, fast reverse)
13. (tune forward, search forward, crawl forward, fast forward)
14. IR remote control sensor
15. LCD screen
16. AS (automatic storage/preset station search, automatic search)
17. USB port
18 AUX IN (auxiliary input)
19. MIC hole (integrated microphone)
20.
In power on mode, press the MUTE button to toggle mute ON or OFF.
21.Release front panel
22.RESET
GENERAL OPERATION
Turn Unit ON/OFF
• Press the power /Mode button on the front panel to turn ON the unit, and
press and hold it again to turn OFF the unit.
• Press the power button on the remote control to turn the unit ON or OFF.
Adjust Volume (VOL)
• Rotate the VOL knob on the front panel or press the VOL+ /VOL- button on
the remote control to increase or decrease the volume level.
FUNCTION
•Press the Volume knob and Rotate to select Audio/Display/Tuner/Clock/Beep/
Animation/Demo mode function. Press the Volume knob again to Select desire
function mode.
AUDIO MODE
•Press the Volume knob and Rotate to select SW Level/Manual EQ/Q factor/Preset
EQ/Bass boost/Loudness/Subwoofer set/Fader/Balance/X’Over/DTA Setting/Car type.
•Long Pless Volume knob to selet 2 way/3 way X’Over mode.
SW LEVEL
•Press the Volume knob and Rotate to select -13 ~ +13 level.
MANUAL EQ
•Press the Volume knob and Rotate to select 25 band frequencies level.
Q FACTOR
•Press the Volume knob and Rotate to select 1/1.5/2.5/3.5 dierent Q factor value.
PRESET EQ
•Press the Volume knob and Rotate to select user/Natural/Rock/Pop/Easy/Top40/
Jazz/Powerful.
BASS BOOST
•Press the Volume knob and Rotate to select Bass bosst level.
LOUDNESS
•Press the Volume knob and Rotate to select Loudness level.
SUBWOOFER SET
•Press the Volume knob and Rotate to Switch ON/OFF.
FADER
•Press the Volume knob and Rotate to select Fader position.
BALANCE
•Press the Volume knob and Rotate to select Balance position.
X’OVER
•Press the Volume knob and Rotate to select Tweeter/Front HPF/Rear HPF/
Subwoofer LPF.
TWEETER
•Press the Volume knob and Rotate to select Frequency/Gain left/Gain right.
FRONT HPF
•Press the Volume knob and Rotate to select Frequency/Gain.
REAR HPF
•Press the Volume knob and Rotate to select Frequency/Gain.
SUBWOOFER LPF
•Press the Volume knob and Rotate to select Frequency/Gain/Phase.
DTA SETTINT
•Press the Volume knob and Rotate to select Position/Distance/Gain/Data Reset/
Delay Unit.
CAR TYPE
•Press the Volume knob and Rotate to select Small/Medium/Large car type.
DISPLAY
•Press the Volume knob and Rotate to select Color Select/Spectrum/ID3 tag
/Version/Dimmer/Language.
DIMMER
•Press the Volume knob and Rotate to select ON/OFF/Dimmer Time.
•Press the Dimmer Time to setting ON Time/OFF Time.
LANGUAGE SELECTION
•
Press Volume button to select Function, enter display, enter language,
turn the knob to select English/Spanish.
COLOR SELECT
•Press the Volume knob and Rotate to select custom R/G/B/Variable Scan/Red/Pink/
Purple/Blue/Cyan/Green/Yellow/Orange.
SPECTRUM
•Press the Volume knob and Rotate to switch ON/OFF.
SPECTRUM
•Press the Volume knob and Rotate to switch ON/OFF.
ID3 TAG
•Press the Volume knob and Rotate to switch ON/OFF.
VERSION
•Press the Volume button to check software version.
TUNER
•Press the Volume button to select Local Seek/Mono Set/Regional/RDS Set.
LOCAL SEEK
•Press the Volume button to rotate switch ON/OFF.
MONO SET
•Press the Volume button to rotate switch ON/OFF.
REGIONAL
•Press the Volume button to rotate to select country regions.
RDS SET
•Press the Volume button to rotate switch ON/OFF.
CLOCK
•Press the Volume knob and Rotate to select Clock Fornat/Clock adjust/Date Fornat/
Date Set.
BEEP
•Press the Volume button to rotate switch ON/OFF.
ANIMATION
•Press the Volume knob and Rotate to select ON/OFF and time interval of animation
time.
DEMO MODE
•Press the Volume button to rotate switch ON/OFF.
Set the clock (CLK)
1. To display the Time press the CLK button.
2. To set the time, press and hold the CLK button and the time will start ashing.
3. Press the or button on the front panel or on the remote control to set the
time.
4. Press the CLK button and the minutes will start ashing.
5. Press the or button on the front panel or on the remote control to set the
minutes.
6. Short Press to Increase Bass Level
Change the source mode (SRC)
Press the SRC button to switch between the button RADIO, BT (Bluetooth), USB
(with a USB device inserted), AUX-IN mode (input assistant).
Loudness: LOUD ON/OFF
Press the LOUD button on the remote control to change the loud volume to boost
the bass output frequency, press again, to turn it o.
DSP SMART ANDROID/IOS APP CONTROL
Subwoofer Control Time Alignment Control
25 EQ ControlX’Over Control
Preset Equalizer (EQ)
Press the EQ button on the front panel or on the remote control to switch between
EQ, OFF, CLASS, ROCK, POP, FLAT.
USB port
The USB port on this stereo device is designed for playing media from USB memory
devices.
GENERAL OPERATION
Integrated Microphone
For voice reception when making a call using the hands-free system.
Auxiliary Input Connector
3.5mm auxiliary input stereo is designed for devices with line output 3.5 mm or
hearing aids.
Reset System
The RESET button is used to reset all factory settings parameters, this function can
be used when the LCD screen does not work properly or if the sound is distorted, or
when some of the controls are disable. Press the RELEASE button to release the
front panel and remove it, use a thin object with a small tip to press the RESET
button over 6 second.
RADIO OPERATION
Change Bands (BAND)
Press the BAND button to switch between the FM1, FM2, FM3 bands.
Each band stores up to six preset stations.
Manual Tuning ( / )
Press and hold the or button on the front panel or on the remote control to
enter manual tuning mode. In manual tuning mode, press the or button to
move the radio frequency number up or down one step.
Auto Seek Tuning ( / )
In standby mode or while not in manual tuning mode, quickly press the or
button to move to the next/previous available station automatically.
To Store/Recall Preset Stations
The radio can store 6 pre-set stations for each band (FM1, FM2 and FM3) for a total
of 18 preset stations.
Memorize a station:
•
Turn the radio on and select the desired band and station.
•
Select a station by or button.
Subwoofer Level control
Select function to select audio, entry subwoofer, entry sw level, turn the knob to select
level 0-8.
Subwoofer frequency control
Select function to select audio, entry subwoofer,entry sw frequency,turn the knob to
select 80Hz/120Hz/160Hz.
• Press and hold the desired preset button (numbered 1-6 on the face of the radio)
for more than 2 seconds to save the station to that preset number.
To recall a preset station
• Select the desired band.
• Briey press a preset button (numbered 1-6) to recall the corresponding preset
station.
Automatic Store station/ Preset station scan (AMS)
Press and hold the AMS button for more than 2 seconds to select six strong stations
and store them in the current band. The radio will automatically scan the current
frequency and enter the six strongest stations into the preset memory positions for
that band. Briey press the AMS button on the remote control to recall each preset
station that saved in the memories in each band.
LOCAL/DX
In urban areas, most stations are strong enough and“LOCAL ON” mode should be
selected. Switch to LOCAL OFF mode to search for stations with weaker signals.
Press the LOC button on the remote control to choose local or distant reception
mode.
STEREO/MONO
FM station is received in stereo mode. However, if the signal is weak or reception is
not as good as you would like, switching to MONO mode usually improves the
overall sound quality. Press the ST button on the remote control to choose FM
STEREO or MONO audio eect.
USB OPERATION
Insert USB
To play les from a USB device, open the USB port cover and insert the USB device
into the port, the songs will begin to play automatically.
Inhaltsverzeichnis
Andere Pyle MP3-Player Handbücher
Pyle
Pyle fleXtreme PSPWP6BK Bedienungsanleitung
Pyle
Pyle PLBKA100BK Bedienungsanleitung
Pyle
Pyle PSWP14BK Bedienungsanleitung
Pyle
Pyle PSPFM1B Bedienungsanleitung
Pyle
Pyle PSHWPMP3 Bedienungsanleitung
Pyle
Pyle PLD-131F Bedienungsanleitung
Pyle
Pyle PLD139 Bedienungsanleitung
Pyle
Pyle PLCD68MP3 Bedienungsanleitung
Beliebte MP3-Player Handbücher anderer Marken
Blaupunkt
Blaupunkt Compact Drive MP3 Bedienungsanleitung
Memorex
Memorex MMP9008 - 8GB USB 2.0 Bedienungsanleitung
Meizu Electronic Technology
Meizu Electronic Technology E5 Bedienungsanleitung
Naxa
Naxa NMV-173NX Bedienungsanleitung
Philips
Philips PSA250 Bedienungsanleitung
Zipy
Zipy go! Waving Bedienungsanleitung
