Pyle PSW976S Bedienungsanleitung
Multifunctional wall mount
IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.
IMPORTANT:
Item No.:PSW976SItem No.:PSW976S
INSTALLATION GUIDE
-12-
Ideal for Flat Panels from 32 to 50""
Weight Capacity:15kg/33lbs~60kg/132lbs
Adjustable Tilt
Adjustable Roll Control
Adjusting the display
Note:
This mount provides a wealth of display adjustment to offer the best viewing from a
number of seating positions. See Fig. 6.
Vertical Tilt Adjustment Angle
Vertical adjustment angle is -5º to 15º.
Left to Right Swivel Adjustment Angle
The display can swivel ±60º from left to right. Choose the desired position and use
provided Wrench to tighten the back bolt on the top of the Arm Assembly.
Stowing the Display -Positions the display against the wall Grasp the side edges of the
display, swivel and pull the display into the center position, and then push the display
straight back towards the wall into the stowed position.
Use care when stowing the display to ensure that cables do not become pinched.
Lateral Tilt adjustment angle is ±5º.
Left to Right Pan Adjustment Angle
The display can pan ±60º from left to right. Choose the desired position and use
provided Wrench to tighten the front bolt on the top of the Arm Assembly.
Adjusting the display
Note:
Fig. 6
±60°
±60°
-5 15°~ °
±60°
±5°
www pyleaudio com..
MADE IN CHINA
Bulit in leveler system
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
-2- -11-
Contents of the ox: Hardware shown as actual size
Make sure that none of these parts are missing before beginning
installation. If there are parts missing stop the installation and contact us.
Contents of the ox: Hardware shown as actual size
Right Bracket
Cable management clip
4
4
4
4
I
J
K
L
M
Square washer
Long bolt
Wall anchor
Long bolt washer
Spacer
ID Description
1
2
4
A
3
5
B
C
1
1
4
4
1
4
4
4
Arm Assembly
Left Bracket
Plastic Cover
M4 mm×12 bolt
M4 mm×16 bolt
M5× mm16 bolt
M6× mm16 bolt
M8×16mm bolt
M ×36mm5 bolt
M6×36mm bolt
M ×36mm8 bolt
Qty
D4
4
4
4
4
4
E
F
G
H
A-H L
IK
JM
ID Description
Qty
1
23
Step 5:Using Cable Management
This mount includes a cable management feature, where cables can be routed along
length of the Arm Assembly. Route the signal cables and power cable along the Cable
management clip as shown in Fig.5. Be sure to leave enough slack for all cables.
With all cables in place, swivel the display at each pivot and check that the Arm
Assembly moves freely, without stretching or damaging the cables.
Step 5:Using Cable Management
4
6
7
6
7
1
1
5X5 Wrench
4X4 Wrench
5
Cable management clip
Cable routing access points
Fig. 5
-10- -3-
WARNING
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
Note:
Caution:This Product LCD /Plasma Wall Mount Bracket is intended for use only
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Caution:
Fig 4b
2,3
1
Knob
Fig 4c
Lock
Open
Lock
Closed
Rod
Step 1: Attach bracket to TV
Check your TV manual to confirm the diameter of bolt to be used or choose an
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-5 of these instructions for examples.
"" .
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts, spacers and washers for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly secure the
bolts. the UP side on the top As shown in Fig.1.
Don't force the bolt into the hole, which will cause a damage of
equipments and injure of person. Don't use electric drill to fasten any bolts.
Note:
IMPORTANT:
Step 1: Attach bracket to TV
IMPORTANT
Note:
UP
Fig 1
UP
-4- -9-
Following examples shows how to use bolts, spacers and square washers.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.
Step 3: Installing the Plastic Cover
Secure the separated Plastic Cover over the Wall Plate by pushing them
towardeachotheruntiltheylockinplace.SeeFig.3.
Step 3: Installing the Plastic Cover
Plastic Cover
Fig. 3
Fig. 4a
Step 4: Hang the Display
Note:
With the help of an assistant, lift the display
intopositioninfrontofthewallplate.
Align the slots on the mounting rails with the
rods on the wall plate, and then lower the
display onto the rods. (Fig. 4c) Make sure that
both rods are fully engaged before releasing
the display.
Prior to lifting the display, make sure
that the flip lock is in the open position, as
shown in Fig. 4a.
Once in place, the lateral position of the
display can be adjusted by gently sliding it
along the rods.
(Fig. 4b)
Step 4: Hang the Display
Note:
Safety Lock
Knob
Lock
Closed
Lock
Open
Fig 1a
M4 Fig bit M5 Fig bit
M6 Fig bit
A,B
3
I
D
3
I
C
I
2
2
E
I
M8 Fig bit
-8- -5-
2. Some displays have curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(M) between display and
thebracket.AsshowninFig1b.
Fig a
Brick, Concrete and Stone wall:
Using a awl or nail to make where the nails are located. Distance between two nails
for fixing wall mount must not less than 16 . Pre-drill these holes with a 10mm drill
bit to at least 80mm in deep hole. Use wall mount as a template to mark the location
of other three holes and drill the same holes. Please make sure these holes are level
and eudipleural. Insert wall anchors(K) into each of these holes. Attach the wall
mount to the wall using 4 long bolts(J) and washers(L).
”
Brick, Concrete and Stone wall:
Fig. 2e
J
L
Concrete Wall
K
Concrete Wall
80
10
Fig. 2d
Fig 1b
M6 Fig bit
F
3I
M
2G
I
M
H
3
I
M
M5 Fig bit
M8 Fig bit
-6- -7-
b
15 degree
viewing angle
eyelevel
a
Fig 2a
Step 2: mount to wall
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 2a).
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15 (Fig 2a).
For example:
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
°
AttachStep 2: Attach mount to wall
After determining the height of stand, follow the installation instructions in below
to install wall mount to different kinds of wall
Using a awl or nail to make where the nails are located, as shown as Fig.2b. Distance
between two nails for fixing wall mount must not less than 16 . Pre-drill these holes
with a 5mm drill bit to at least 80mm in deep hole. Use wall mount as a template to
mark the location of other three holes and drill the same holes.
Fix the wall mount to the wall with 4 long bolts(J) and
washers(L).
-wooden, brick, concrete and stone.
Please make sure these
holes are level and eudipleural.
Wooden wall:
”
Wooden wall:
Fig. 2b
16”
80
5
Fig. 2c
J
L
Wood stud
Inhaltsverzeichnis
Andere Pyle TV-Halterung Handbücher
Pyle
Pyle PSW101CM Bedienungsanleitung
Pyle
Pyle PSWLE54 Bedienungsanleitung
Pyle
Pyle PWLB008 Bedienungsanleitung
Pyle
Pyle PSW119ST1 Bedienungsanleitung
Pyle
Pyle PSW598UT Bedienungsanleitung
Pyle
Pyle PSWLE81 Bedienungsanleitung
Pyle
Pyle PSW449T Bedienungsanleitung
Pyle
Pyle PSWLE58 Bedienungsanleitung
Pyle
Pyle PSW116MF1 Bedienungsanleitung
Pyle
Pyle PWLB805 Bedienungsanleitung
Pyle
Pyle PSWLE57 Bedienungsanleitung
Pyle
Pyle PYWM24 Bedienungsanleitung
Pyle
Pyle PSWLE82 Bedienungsanleitung
Pyle
Pyle PWLB121 Bedienungsanleitung
Pyle
Pyle PSWLE59 Bedienungsanleitung
Pyle
Pyle PYWM78 Bedienungsanleitung
Pyle
Pyle PSWLE08 Bedienungsanleitung
Pyle
Pyle PSW976S Bedienungsanleitung
Pyle
Pyle PSW601AT Bedienungsanleitung
Pyle
Pyle PSW101CM Bedienungsanleitung
