QM-products SPM-2011 Bedienungsanleitung

QM-Products 2016 v1.0

SPM-2011

2 x HDMI/AV to 1 x DVB-T/C

Operation Manual

QM-Products 2016 v1.0

1. IMPORTANT SAFETY PRECAUTIONS INFORMATION

READ THE FOLLOWING WARNINGS BEFORE YOU USE

YOUR DEVICE

WARNING

The following safety precautions must be observed to prevent fire or electric

shock hazard. Safety precautions include but are not restricted to the following:

Power supply / Mains cord

Operate the unit only within the voltage range defined as appropriate by the

manufacturer.

Occasionally check the power connector and remove dirt or dust that may

have accumulated.

Use only the mains cord that comes with your unit.

Do not operate the unit or plug in the mains cord if it is broken, split, or

damaged in any way.

Do not place the mains cord next to heating devices. Do not pull it, place

heavy objects on it or damage it in any way. Keep it out of reach of children.

Ensure that the device is plugged in a proper grounded socket. Insufficient

grounding may cause electrocution.

Always carefully disconnect all plugs by taking off the plug and strictly

forbitten to pull the cord in order to disconnect the unit . Make sure the unit's

power switch is turned off before removing the cord from an outlet.

Disconnect the mains cord when the unit is not in use for long periods of time

or during storms.

Do not connect the unit to a multiple-outlet to avoid plug overheating.

Disassembling

This unit contains parts that cannot be repaired by the user. Do not

disassemble or try to repair it as this will void all warranties. Please contact

the manufacturer if you experience any problems with your unit.

Water/humidity

Do not keep the unit in a humid place or near water.

Do not plug/unplug the unit with wet hands.

Fire

Never place a candle or another source of fire on the unit as it may fall and

start a fire.

If the mains cord or the power connector is damaged or destroyed, or if there

is a sudden loss of picture during operation, or if you notice a strange smell or

there is smoke, immediately switch the unit off, disconnect the mains cord and

contact the manufacturer’s technical support department.

QM-Products 2016 v1.0

Installation / Storage

This unit contains high precision pieces of electronics. To ensure optimal

performance and avoid damage, do not store it in any location where it may

collect dirt, duct, lint, etc. Do not expose it to extreme heat or cold (e.g. in

direct sunlight, near a heater or in the car during the day). Place the unit in a

secure place to avoid falls.

Before moving the unit, always unplug all cords first.

When installing the unit, make sure that an outlet is within easy reach. In case

of malfunction, switch the unit off and unplug the power cord. When the unit

is not in use for a long period of time, make sure that the mains cord is

disconnected.

Connectivity

Before connecting the unit to other electronic devices, always switch off and

unplug all devices.

Maintenance

Do not spill liquids on the unit. Do not use any diluents or volatile liquid to

clean the unit. Instead, use a soft slightly damp cloth and allow the unit to dry

completely before using again.

Handling

Do not poke your finger into the openings on your unit.

Never put paper, metal parts or other objects into the openings of your unit. If

you suspect that there are foreign parts in your unit, switch it off and unplug

the mains cord. Contact the manufacturer’s technical support department.

Do not step on or place heavy objects on top of the unit. To avoid hardware

damage, handle all buttons, connectors and switches gently.

QM-Products 2016 v1.0

2. INTRO

Congratulations on purchasing the SPM-2011. You now own a high quality,

semiprofessional DTV modulator. To get the most out of your purchase, please take

the time to read carefully through this manual.

3. INSTRUCTIONS

3.1 DESCRIPTION

The SPM-2011 is a very powerful, all-in-one device, able to receive up to 2

independent HDMI/AV sources and to convert them in 1 x DVB-T/C RF output

channel. The embedded web server of the SPM-2011 provides a very friendly user

interface as well as the ability of remote or local control of the device via Ethernet.

Its small size and its powerful features makes the SPM-2011 the ideal solution to

distribute HDMI/AV sources coming from eg. a STB or DVD player to a CATV

installation using the DVB-T/C signals.

3.2 FEATURES

2 x independent HDMI/AV inputs

1 x RF output DVB-T/C (software selectable)

Full NIT Configuration

Low power consumption

MER value > 40dB

Very clean RF spectrum

PCR re-stamping

Very friendly user interface

Wall mountable

Compact size

5 year warranty

3.2.1 Auto-reset functions and watchdog

During the normal operation of the SPM-2011 , the main CPU monitors all the

internal parts in order to ensure that the device works normally. In case of an internal

error or module failure, the SPM-2011 immediately initiates the recovery procedure

by resetting the appropriate module or the device. Finally, watchdog timers ensure

that the device will be reset in case of CPU failure.

3.2.2 DVB-T or DVB-C compliant

The user is able to software select the modulation standard, between DVB-T and

DVB-C, of the SPM-2011 without the need of any firmware upgrade.

QM-Products 2016 v1.0

SPM-2011

1. Reset button

2. Status LED

3. IP LAN control

4. RF output

5. RF input

6. HDMI/AV inputs

QM-Products 2016 v1.0

4. INSTALLATION

4.1 General

The SPM-2011 has a very friendly interface for programming and monitoring

purposes. The user is able to gain access to the embedded webserver, by opening an

Internet browser (eg. Internet Explorer, Firefox or Chrome) and type the following

static IP: 192.168.1.200.

The default username and password are the following:

Username: admin

Password: 12345

4.2 Embedded Webserver

Status

4.2.1 “General” page

Figure No 1

Every time that the user is connected to the device, the “General” page (Figure No 1)

is loaded providing a current general status information of the device.

QM-Products 2016 v1.0

Status - Inputs 1.2.

In these fields, the user is able to see the status of each HDMI/AV input eg. if the

H.264 encoder is running or if it is in idle state, its Service name, its Service ID,

video/audio PID and LCN number.

Output –Modulator

In these fields, the user is able to see the status of all the RF output of the device such

as modulator state, RF output frequencies and modulation settings.

System

This section provides general information of the device, like internal status of all

device’s modules, CPU temperature and fan state as well as error codes for

troubleshooting purposes.

Setup

4.2.2 “Input”page

Figure No 2

QM-Products 2016 v1.0

In the “Input page” ( Figure No 2) the user is able to setup each HDMI/AV input

independently. There are two tabs including all the 2 HDMI inputs. For each input the

user needs to program the following fields:

1. Input Enabled/Disabled - Enable or disable the specific HDMI input

2. Service Name –Insert the preferred service name

3. Service ID –Insert the service ID number

4. Video Bitrate –Set the video bitrate (2000-19000 Kbps)

5. Audio Bitrate –Set the audio bitrate (64,96,128,192,256,320 Kbps)

6. Audio encoding –Set the audio encoding (AAC, AC3, Mpeg2)

7. HDCP –Enable/disable the HDCP function

8. LCN –Set the LCN number

9. PMT PID –Set the PMT PID

10. Video PID –Set the Video PID

11. Audio PID –Set the Audio PID

Once all settings are being written, the user must click the “Apply” button for the

settings to be saved.

4.2.3 “RF Output” page

Figure No 3

QM-Products 2016 v1.0

In the “RF Output” page (Figure No 3) the user is able to setup the RF output settings

of the SPM-2011.

With the use of the radio buttons the user is able to select the mode that the

SPM-2011 will operate as follows:

DVB-T: modulator working in DVB-T standard

DVB-C: modulator working in DVB-C standard

For each modulator in DVB-T mode the user is able to setup the following

parameters:

Frequency –The output frequency

Constellation –The constellation

Code Rate –The coder rate

Guard Interval - The guard interval

Channel Bandwidth –The channel bandwidth

Modulation –The modulation type

Enable/Disable –Enable or disable the modulator

Output level –Adjust the output level from 70-90dΒμV.

The status section provides a general idea to the user of the current payload

(according to the selected programs) comparing to the max. output payload.

It is recommended that the user must not exceed the 85% from each output, since all

the bitrate are variable according to their specific content.

4.2.3 “Multiplexer” page

In this section (Figure 4), the user is able to setup all the TS settings of the multiplexer

in SPM-2011 output.

Figure No 4

QM-Products 2016 v1.0

The user can setup the following settings:

TS ID: Which is the ID No of the specific multiplex. (1…65535)

Net ID: Which is the Net ID No of the specific multiplex. (1…65535)

Original Net ID: Which is the Org. Net ID No of the specific multiplex. (1…65535)

Network Name: Which is the network name of the specific multiplex

NIT: User can choose the following options (Off , Basic , Auto , Custom)

LCN provider: Choose the appropriate LCN provider (EACEM, ITC, Nordig, APN)

4.2.4 “NIT” page

In “NIT” page (Figure No 5) the user is able to create a full customize NIT table

Figure No 5

Inhaltsverzeichnis

Andere QM-products Modulator Handbücher

QM-products

QM-products DFL-100H Bedienungsanleitung

Beliebte Modulator Handbücher anderer Marken

axing

axing AVM 5-00 Bedienungsanleitung

IKUSI

IKUSI MAC-HOME HD Bedienungsanleitung

Wisi

Wisi MINI OM 10 Bedienungsanleitung

RCA

RCA CRF910 Bedienungsanleitung

Pico Macom

Pico Macom PM45 Bedienungsanleitung

FTE Maximal

FTE Maximal MODIG AIR Bedienungsanleitung

Thor Broadcast

Thor Broadcast H-IP-32RF Bedienungsanleitung

Delphi

Delphi SA10003 Bedienungsanleitung

Elan

Elan MOD3000 Bedienungsanleitung

ClearView

ClearView SD4260 Bedienungsanleitung

Televes

Televes T.0X COFDM-QAM CI Bedienungsanleitung

Crucial Audio

Crucial Audio Die Gotterdämmerung Bedienungsanleitung

Pioneer

Pioneer CD-V61FM Bedienungsanleitung

Televes

Televes 554912 Bedienungsanleitung

Newtec

Newtec M6100 Bedienungsanleitung

ProTelevision

ProTelevision PT 5780 Bedienungsanleitung

Argent Cables

Argent Cables HD DVB-T MODULATOR Bedienungsanleitung

SSS Siedle

SSS Siedle BVM 650-0 Bedienungsanleitung