QMS 3225 Bedienungsanleitung

QMS 3825/3225

Print System

Large-Large-

Capacity Input

Tray Option



1800403-001C

This document was created with FrameMaker 4.0.4

Trademarks

The following are trademarks or registered trademarks of their respective owners.

Other product names mentioned in this manual may also be trademarks or registered

trademarks of their respective owners. Registered trademarks are registered in the

United States Patent and Trademark Ofﬁce; some trademarks may also be registered in

other countries. QMS, the QMS logo, Crown, and the Crown seal are registered

trademarks of QMS, Inc., and PS Executive Series is a trademark of QMS, Inc.

Proprietary Statement

The digitally encoded software included with your QMS 3825/3225 Print System is

Copyrighted



reproduced, modiﬁed, displayed, transferred, or copied in any form or in any manner or

on any media, in whole or in part, without the express written permission of QMS, Inc.

This manual is Copyrighted



1995 by QMS, Inc., One Magnum Pass, Mobile, AL

transferred to any other media or language, without the express written permission of

QMS, Inc.

Contents

Introduction .....................................................................................1

Installing the LLCIT 1

Moving the Printer 1

Large-Large-Capacity Input Tray Indicators 2

Selecting a Paper Size 2

Adding Paper to the LLCIT .............................................................3

Changing LLCIT Paper Size ...........................................................4

Remove and Disassemble the LLCIT 4

Set DIP Switches to Match Paper Size 9

Adjust Side Rails to Match DIP Switches 10

Reassemble the LLCIT 17

❖

This document was created with FrameMaker 4.0.4

Introduction

QMS 3825/3225 Large-Large-Capacity Input Tray Option

Introduction

The Large-Large-Capacity Input Tray (LLCIT) for your QMS 3825/

3225 Print System allows you to load 2,500 sheets of paper at a time,

in letter, legal, ledger,A3,A4, and B4 sizes.

Installing the LLCIT

The LLCIT must be installed by a QMS-authorized service represen-

tative. See appendix A, “QMS Customer Support,” in your printer

manual if you do not know how to reach your service contact.

Moving the Printer

Because the LLCIT holds a heavy load, it has a metal prop plate at

the back corner for added support. The prop plate helps prevent the

printer from tipping, even when the LLCIT is fully loaded. If you need

to move the printer, you must

■

Remove the paper from the LLCIT

■

Remove the prop plate to avoid damage to the printer or the ﬂoor

To remove the prop plate, simply remove the two screws holding it in

place. The prop plate slips off easily. Reinstall the prop plate as soon

as the printer is in its new location.

Be careful not to tip the printer while moving it.

WARNING!

Once the LLCIT is installed, if you need to move the printer

from place to place, you must remove the metal prop plate from under the

back corner of the LLCIT. Be careful not to tip the printer while moving it.

ACHTUNG!

Soll der Drucker versetzt werden and der LLCIT ist installiert,

müssen Sie die Metallstütze unter der hinteren Ecke des LLCIT entfernen.

Achten Sie beim Verschieben darauf, daß das Drucksystem nicht kippt.

This document was created with FrameMaker 4.0.4

QMS 3825/3225 Large-Large-Capacity Input Tray Option2

Introduction

Large-Large-Capacity Input Tray Indicators

The Large-Large-Capacity Input Tray (LLCIT) has step-by-step

instruction illustrations, a button to lower the interior tray, and an error

light to alert you to any condition that requires your attention.

Selecting a Paper Size

Changing the paper size for the LLCIT requires special care to avoid

damaging electrical connections. We recommend that you

✓

Evaluate your printing needs and choose one size for the

LLCIT

✓

Have the service representative set the LLCIT for that size

during installation

✓

Do not alter the size setting

» Note: Only a qualified QMS service technician should change the LLCIT size

settings. Service instructions for changing the paper size begin on page 4. If

you damage the printer or the Large-Large-Capacity Input Tray while

changing the size settings, it will affect your warranty.

Instruction Illustrations

Once you know how to load paper from

reading this manual, the step-by-step

illustrations will help you remember in what

order to perform the various steps.

Tray Down Button

Press this button to lower the paper tray inside

the LLCIT. The tray must be at the bottom

position before you can load paper.

If the printer runs out of paper, the tray lowers

automatically.

This button lights when the tray is in motion.

Error Light

This red light comes on if paper is loaded

incorrectly, if the paper size does not match the

tray’s setting, or if the LLCIT door is open.

Adding Paper to

the LLCIT

QMS 3825/3225 Large-Large-Capacity Input Tray Option

Adding Paper to the LLCIT

The LLCIT holds up to 2,500 sheets of paper in letter, legal, ledger,

A3, A4, and B4 sizes. Once the size is set, add paper of the same

size and orientation as the paper that was previously loaded.

» Note: Only a qualified QMS service technician should change the LLCIT paper

size. Service instructions begin on page 4. If you damage the printer or the

Large-Large-Capacity Input Tray while changing the size settings, it will

affect your warranty.

To add paper to the LLCIT

1 Remove the upper and lower input bins.

2 Push the Tray Down button to lower the interior paper tray.

The tray moves slowly.

3 When the light stops ﬂashing, open the LLCIT door and lift

the clear plastic lid.

4 Remove and discard the top and bottom sheets from the new

paper supply.

Top and bottom sheets sometimes have traces of glue which can

cause jams.

5 Follow the paper manufacturer’s instructions as to which

side of the paper should be printed on ﬁrst.

Printing on the proper side ﬁrst helps prevent excessive paper

curl, which is especially important if you are using the optional

Large-Capacity Output Stacker (LCOS). The paper wrapper usu-

ally has an arrow to indicate which side to print on ﬁrst. Load

paper so the arrow points up.

6 Bow the paper slightly to insert it into the bin, and slide it in

until it is aligned with the innermost edge of the bin.

» Note: Make sure to use the same size paper in the same orientation as

you were using before.

7 Close the lid, and shut the door until it snaps.

8 Wait for the paper tray to reach its uppermost position.

QMS 3825/3225 Large-Large-Capacity Input Tray Option4

Changing LLCIT

Paper Size

Changing LLCIT Paper Size

Changing the paper size for the LLCIT requires special care to avoid

damaging electrical connections. We recommend that you:

✓

Evaluate your printing needs and choose one size for the LLCIT

✓

Have the service representative set the LLCIT for that size

during installation

✓

Do not alter the size setting

» Note: Only a qualified QMS service technician should change the LLCIT size

settings. The following instructions are included to assist service personnel.

If you damage the printer or the Large-Large-Capacity Input Tray while

changing the size settings, it will affect your warranty.

Remove and Disassemble the LLCIT

» Note: Before you begin this procedure, note the paper size setting.You will

need to know what you are changing from to complete the process.

WARNING!

It takes two people to lift the LLCIT in and out of the

printer. Do not lift the LLCIT with paper loaded in it.

ACHTUNG!

Man benötigt 2 Personen um den LLCIT zu tragen. Tragen

Sie den LLCIT nie mit eingelegtem Papier.

1 Remove the upper and lower input bins.

2 Press the Tray Down

button.

3 As soon as the tray

moves down enough to

remove the paper, open

the door to stop the tray

movement.

4 Remove all the paper.

Changing LLCIT

Paper Size

QMS 3825/3225 Large-Large-Capacity Input Tray Option

5 Close the door. The tray will rise to the top.

6 When the tray reaches the top, open the door.

7 Turn off the printer.

8 Shut the door.

9 Remove the metal prop plate from beneath the back corner

of the LLCIT by removing the two screws that attach it and

slipping off the plate.

Set aside the prop plate and screws to reinstall after you ﬁnish

with the tray.

10 Lift and pull the LLCIT

from the printer as you

would any input bin.

Set it gently on the ﬂoor,

being careful not to over-

extend the cable at the

back-right corner of the

tray.

QMS 3825/3225 Large-Large-Capacity Input Tray Option6

Changing LLCIT

Paper Size

11 Unscrew the silver screw from the top back of the indicator

area cover.

12 Open the front door of the LLCIT.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung