Quaddrix QT-220EX Bedienungsanleitung
1
QT-220EX
26X Day/Night PTZ Dome
USER’S MANUAL
Document Version 1.1
October 06, 2005
TABLE OF CONTENTS
Chapter 1 Installation Preparation..............................................................6
1.1 Tools Lists ......................................................................................................... 6
1.2 Cables .............................................................................................................. 6
1.3 DIP switches and jumpers settings........................................................................ 7
Chapter 2 Installation Type Guide...............................................................8
2.1 IN-CEILING MOUNT ...........................................................................................10
2.2 SURFACE MOUNT ..............................................................................................14
2.3 WALL MOUNT....................................................................................................18
2.4 CORNER MOUNT................................................................................................21
2.5 POLE MOUNT ....................................................................................................24
2.6 PENDANT MOUNT ..............................................................................................27
Chapter 3 SYSTEM CONNECTION...............................................................31
3.1 OPERATION INSTRUCTION..................................................................................32
3.2 MENU TREE ......................................................................................................34
3.3 MENU OPERATION .............................................................................................35
3.3.1 Selecting item.............................................................................................35
3.3.2 Changing values..........................................................................................35
3.3.3 Editing titles ...............................................................................................36
3.4 SYSTEM INFO ...................................................................................................37
3.4.1 SITE INFORMATION.....................................................................................37
3.4.2 DISPLAY CONFIGURATION............................................................................38
3.4.3 CHANGE PASSWORD....................................................................................38
3.4.4 FACTORY DEFAULT ......................................................................................39
3.4.5 RESTART....................................................................................................40
3.5 LENS PARAMETERS............................................................................................40
3.6 CAMERA PARAMETERS .......................................................................................42
3.7 PAN/TILT PARAMETERS ......................................................................................45
3.8 AUTO RUNNING ................................................................................................47
3.8.1 PRESET......................................................................................................47
3.8.2 TOURING ...................................................................................................48
3.8.3 PATTERN....................................................................................................50
3.8.4 AUTO SCAN................................................................................................51
3.8.5 SET ZONE ..................................................................................................52
3.8.6 FUNCTION IDLE AND FUNCTION....................................................................53
Appendix I: Dip Switch & Jumper Settings................................................55
2
Appendix II: Wire Diameter & Transmission.............................................62
Appendix III: RS485 Bus Basic Knowledge...............................................63
Appendix IV: Lighting Proof & Surge Signal Proof.....................................66
Appendix V: The Cleaning of the Clear Down Cover...................................68
Appendix VI: Trouble Shooting .................................................................69
3
4
DECLARATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC rules and the European Union
89/336/EEC directive and its latest amended version. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required
to correct the interference at own expense.
Modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment under CE and FCC rules.
PRECAUTIONS
1. Only qualified and experienced personnel can carry on the installation.
2. Always conform to national and local safety codes during installation.
3. Use reliable tools only, poor quality tools may cause danger.
4. Install the speed dome in an appropriate environment (Refer to the chart below).
This product conforms to IP66 standard as specified in “Housing Protection
Classification (IP code)”.
5. Check the site space and resistance before installing. It should be able to bear 4
times the weight of the dome and its accessories.
6. Keep all the original dome package materials in case of future repacking and
transportation.
WARNINGS
1. DO NOT install this speed dome in hazardous places where combustible or
explosive materials are stored or used.
2. DO NOT install indoor domes in an outdoor environment.
3. This speed dome runs on 24v AC. DO NOT connect higher or lower voltage to it.
4. DO NOT turn power on before completing installation.
5. DO NOT disassemble any part of the items.
6. Use a soft towel to clean the down cover when necessary. DO NOT use caustic
detergent.
7. DO NOT place the camera to be hit by strong lighted objects.
5
Chapter 1 Installation Preparation
1.1 Tools Lists
You may need following tools for the installation:
•Screws and nuts
•Philips screw driver
•Minus screw driver Wire scissors,
•Ladder
•Drill
•Saw
1.2 Cables
Video Coaxial Cable:
The video coaxial cable should be:
•1) 75 ohm impedance,
•2) Solid copper wire,
•3) 95% braided copper shield.
•Check the max. transmission distance referring to the chart below.
RS485 Cable: 0.56mm (24AWG) twisted pair. Wire’s maximum transmission
distances are as follows.
NOTE: Use RS485 distributor if you need to transfer further. To learn more about
RS485, see Appendix III.
6
7
1.3 DIP switches and jumpers settings
Refer to Appendix I to configure the following:
•Protocol and Baud rate
•Dome address
•Video cable type
•Resistor jumper
•Alarm output method
WIRING DIAGRAM FOR ALARM, VIDEO & RS485 AND POWER
TYPE GUIDE INSTALLATON
8
Chapter 2 Installation Type Guide
Three main kinds of installation are available for the QT-220EX:
1) In-ceiling Mount,
2) Surface Mount,
3) Bracket Mount.
There are 4 options for the bracket mount:
1) Wall Mount,
2) Corner Mount,
3) Pole Mount,
4) Pendant Mount.
NOTE: Installation site should be able to withstand at least 4 times the weight of
the dome.
Bracket mount dome has an Indoor type and an Outdoor type. Comparing to the indoor
type, the Outdoor type has extra sun-shield housing, temperature sensor and heater.
Also, the Outdoor type conforms to IP66 standard. (Refer to appendix IV)
WARNING: DO NOT install an indoor dome in an outdoor environment.
In-ceiling Mount
9
Surface Mount
Bracket Mount
1. Wall Mount 2. Corner Mount
3. Pole Mount 4. Pendant Mount
10
2.1 IN-CEILING MOUNT
Installation requirement:
1. The thickness of the ceiling should
be less than 42mm.
2. The ceiling should be able to bear
4x of the weight of the speed dome.
3. Upper space should be at least
20cm high.
1. Draw a circle on ceiling.
Take the paper circle (accessory) as a
template to draw a circle on the ceiling.
The paper circle’s diameter is 225 mm.
2. Cut the circle off.
Use a saw or proper tool to cut off the circle.
NOTE: Make sure the diameter of the circle is
225+2mm before cutting the circle off.
Inhaltsverzeichnis
Andere Quaddrix Sicherheitskamera Handbücher
