quadient AS-3630 Bedienungsanleitung
3630 Quick Start Guide Rev. 1-9-15 1
3630, QUICK START GUIDE
1. Carefully unpack the printer, feeder, conveyor and accessories.
Save the packing materials.
2. Choose a suitable location for the printer. Not in direct sunlight.
3. With the help of another person; lift the printer, using the “recessed carrying
handles”, and place the printer onto a sturdy table that can safely support the weight
of the printer.
4. Position the optional feeder stand and feeder (FDR12, FDRSS) at the entrance end
of the printer.
NOTE: The User Manual (Operators’ Guide) describes the use of the FD-13/15
Feeder. This feeder is not offered in the USA.
5. Position the optional conveyor/stacker/dryer at the exit end of the base.
6. Verify the proper connections as outlined below.
3630 Connections
•Strapping Plugs (dummy plugs) must fill all open positions, in the Emergency Stop
connection area, on the printer.
Be sure to use the proper strapping plug, as shown above.
oStrapping Plug OUT (has red marker) must be connected to the OUT (RENA
OUT) connection (has red circle) on the printer.
oStrapping Plug IN must be connected to the IN (RENA IN) connection on the
printer.
•Attach the appropriate “Feeder Interface Cable” between the Printer and the Feeder.
If you are using the FDR12 or FDRSS feeder models; use cable part # 9200661 to attach
the “Relay 2” connection on the Controller and the Feeder.
7. Check to be sure that the red Emergency Stop Button is released (reset).
8. Connect AC power to the printer; using the supplied power cord.
9. Power the printer ON. Set power switch to 1.
10. After a number of seconds the controller will display: EMERGENCY BUTTON
SHOULD BE RELEASED!.
Strapping Plug
OUT
Strapping Plugs
IN
Feeder Interface
Cable (Relay 2)
3630 Quick Start Guide Rev. 1-9-15 2
11. Press the green button on the printer, to activate the Emergency Circuit. This button should
illuminate and the “EMERGENCY BUTTON… message should go away.
Tip: If the green button does not illuminate and the “EMERGENCY BUTTON…”
message does not go away, check to be sure all Strapping Plugs are properly
connected, the Emergency Stop Button has been released (reset), the Plexiglas
Cover is closed and the “Finger Guard” is closed.
12. The copper “Grounding Straps” are provided to attach
adjacent devices together and reduce the chance for “static
discharge” between devices; which can damage electronics.
Attach these straps to a good earth ground connection on the
conveyor and feeder.
13. Please refer to the User Manual (Operator’s Guide) for
instructions on how to install the printer driver, connecting the
computer, install the ink cartridges and operate the printer.
Identifying Cables and Plugs Included with 3630 System:
QTY
Manufactures #
NISL/SAP
Description
1
G0635.1.756.00
9200561S
5-POLE CABLE
NOTE: This cable is not normally needed or used.
This pigtail cable (no connector on one end) can be used to
connect the Emergency Stop “Extern” connection to an
“external device”. The “external device” would need to have
Emergency Stop features that are compatible with the printer.
Pins 1 & 2 Emergency Stop Input (closed = run, open = stop)
Pins 3 & 4 Emergency Stop Output (closed = run, open = stop)
2
G0635.1.755.00
4141957N
EMERGENCY STOP STRAPPING PLUG OUT
This “dummy plug” has a RED identification mark on it. It must
be installed in any open Emergency Stop “OUT” connection on
the back of the printer.
4
G0635.1.754.00
4141958P
EMERGENCY STOP STRAPPING PLUG (dummy plug) IN
This “dummy plug” must be installed in any open Emergency
Stop “IN” connectors on the back of the printer.
Additional Items/Accessories Commonly Needed for 3630 System:
QTY
Manufactures #
NISL/SAP
Description
1
Feeder (FDR12 or FDRSS)
1
8703946K
Feeder Stand, Adjustable (FDRSSTAND)
1
G0620.1.740
9200661
Feeder Interface Cable
Connects from the “Relay 2” connection on the Printer to the
Feeder (FDR12, FDRSS). Allows the printer to control the
start/stop function of the feeder.
Conveyor Stacker
Dryer
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere quadient Postausrüstung Handbücher
quadient
quadient IJ-15K Bedienungsanleitung
quadient
quadient IS-480 Bedienungsanleitung
quadient
quadient IS-420 Bedienungsanleitung
quadient
quadient iX-5 Series Bedienungsanleitung
quadient
quadient CS-200 Bedienungsanleitung
quadient
quadient IN-360 Series Bedienungsanleitung
quadient
quadient IS-6000 Bedienungsanleitung
quadient
quadient iX-5 Series Bedienungsanleitung
quadient
quadient IN-600 Bedienungsanleitung
quadient
quadient IS-6000 Bedienungsanleitung
quadient
quadient IS-280 Bedienungsanleitung
quadient
quadient IS-430 Bedienungsanleitung
quadient
quadient IJ-15K Bedienungsanleitung
quadient
quadient IX-7 Bedienungsanleitung
quadient
quadient IS-440 Bedienungsanleitung
quadient
quadient IS-350 Bedienungsanleitung
quadient
quadient IS-330 Bedienungsanleitung
quadient
quadient IM-22 Bedienungsanleitung
quadient
quadient IN-360 Series Bedienungsanleitung
quadient
quadient iX-5 Series Stücklistenhandbuch
