Quadra-Fire 5100 ACC Bedienungsanleitung

1 7047-910C August 25, 2014

51-I ACC WOOD INSERT

Automatic Combustion Control (ACC)

Model(s):

5100 ACC

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

ﬁreplace.

• Alert children and adults to hazards of high temperatures

• High temperatures may ignite clothing or other

ﬂammable materials.

• Keep clothing, furniture, draperies and other ﬂammable

materials away.

WARNING

If the information in these instruc-

tions is not followed exactly, a

ﬁre may result causing property

damage, personal injury, or death.

• Do not store or use gasoline or other ﬂam-

mable vapors and liquids in the vicinity of

this or any other appliance.

• Do not overﬁre - If heater or chimney con-

nector glows, you are overﬁring. Overﬁring

will void your warranty.

• Comply with all minimum clearances to

combustibles as speciﬁed. Failure to

comply may cause house ﬁre.

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may overﬁre and generate

poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should

be performed by qualiﬁed personnel. Hearth &

Home Technologies recommends NFI certiﬁed

professionals, or technicians supervised by an

NFI certiﬁed professional.

WARNING

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

To obtain a French translation of this manual, please contact

your dealer or visit www.quadraﬁre.com

Pour obtenir une traduction française de ce manuel, s’il vous

plaît contacter votre revendeur ou visitez www.quadraﬁre.com

2 7047-910C August 25, 2014

5100 I-ACC

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided may result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

1 Important Safety Information.........3

A. Insert Certiﬁcation.............................................................3

B. BTU & Efﬁciency Speciﬁcations........................................3

C. Mobile Home Approved.................................................... 3

D. Glass Speciﬁcations.........................................................3

E. Non-Combustible Materials ...............................................3

F. Combustible Materials........................................................3

2 Getting Started................................4

. Design and Installation Considerations..................................4

B. Draft..................................................................................4

C. Negative Pressure ...........................................................5

D. Tools And Supplies Needed .............................................5

E. Inspect Appliance and Components.................................5

F. Install Checklist ..................................................................6

3 Dimensions and Clearances..........7

A. Appliance Dimensions ......................................................7

B. Clearances to Combustibles, ............................................8

C. Locating Your Stove & Chimney.......................................9

D. Chimney Termination Requirements ................................9

E. 2-10-3 Rule ......................................................................10

4 Chimney Systems...........................11

A. Venting Systems...............................................................11

B. Inspections........................................................................11

C. Larger Chimneys..............................................................11

D. Masonry Chimney.............................................................11

E. Metal Heat Circulating Masonry .......................................13

F. Prefabricated Metal Chimney............................................13

G. Securing Chimney Components.......................................14

H. Altering the Fireplace........................................................14

I. Zero-Clearance Fireplace ..................................................15

J. Ovalizing Round Stainless Steel Liners ............................15

K. Chimney Height / Rise and Run .......................................15

5 Appliance Set-Up............................16

A. Outside Air Kit Installation..................................................16

B. Securing Stove Pipe/Liner to Flue Collar..........................17

C. Optional OffsetAdapter Installation..................................17

D. Leveling Legs ..................................................................18

E. Securing Appliance to Stove Pipe/Liner............................18

F. Surround & Trim Kit Installation.........................................18

G. Blower Cord Installation on Left Side ..............................19

H. Zero Clearance Adjustable Trim Support, 2” to 10” .........21

6 Mobile Home Installation................22

7 Accessory List ................................23

August 25, 2014 7047-910C 3

5100 I-ACC

Model: 5100-I (ACC) Insert

Laboratory: Intertek

Report No: 100323198PRT-001a

Type: Solid Fuel Type, Listed Room Heater

Standard: UL1482 and ULC S628-93 and

(UM) 84-HUD, Mobile Home

Approved.

The Quadra-Fire 5100 Wood Insert (ACC) meets the U.S. Environ-

mental Protection Agency’s 1990 particulate emission standards.

EPA Certiﬁed: 4.17 grams per hour

Efﬁciency: up to 80.5%

EPA BTU Output: 10,500 to 27,900

Heating Capacity: 2,250 to 3,175 sq ft depending

on climate zone

Vent Size: 6 inches

Firebox Size: 3 cubic feet

Max Wood Length: 22 inches

Max First Hour BTUs: 73,200 @ 75.5% B415 Tested

Efﬁciency

Fuel: Cord Wood

Shipping Weight: 480 lbs

1 Important Safety Information

A. Insert Certiﬁcation

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their

speciﬁcations and/or price without notice.

C. Mobile Home Approved

• This appliance is approved for mobile home installa-

tions when not installed in a sleeping room and when

an outside combustion air inlet is provided.

• The structural integrity of the mobile home ﬂoor, ceil-

ing, and walls must be maintained.

• The appliance must be properly grounded to the frame

of the mobile home with #8 copper ground wire, and

chimney must be listed to UL103 HT or a listed UL-

1777 full length six inch (152mm) diameter liner must

be used.

• Outside Air Kit, part OAK-ACC must be installed in a

mobile home installation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualiﬁed

installer, service agency or your dealer.

Quadra-Fire is a registered trademark of Hearth & Home

Technologies.

• Installation and use of any damaged appliance.

• Modiﬁcation of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved by

Hearth & Home Technologies.

• Operating appliance without fully assembling all components.

• Operatingappliancewithout legsattached (ifsuppliedwith unit).

• Do NOT Overﬁre - If appliance or chimney connector glows,

you are overﬁring.

Any such action that may cause a ﬁre hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided by,

the following actions:

B. BTU & Efﬁciency Speciﬁcations

D. Glass Speciﬁcations

This stove is equipped with 5mm ceramic glass. Replace

glass only with 5mm ceramic glass. Please contact your

dealer for replacement glass.

Hearth & Home Technologies WILL NOT warranty stoves

that exhibit evidence of over-ﬁring. Evidence of over-ﬁring

includes, but is not limited to:

• Warped air tube

• Deteriorated refractory brick retainers

• Deteriorated bafﬂe and other interior components

E. Non-Combustible Materials

Material which will not ignite and burn, composed of any

combination of the following:

- Steel - Plaster

- Brick - Iron

- Concrete - Tile

- Glass - Slate

Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace of 750° C.

F. Combustible Materials

Material made of/or surfaced with any of the following ma-

terials:

- Wood - Compressed Paper

- Plant Fibers - Plastic

- Plywood/OSB - Sheet Rock (drywall)

Any material that can ignite and burn: ﬂame proofed or not,

plastered or un-plastered.

NOTE: This installation must conform with local codes. In the

absence of local codes you must comply with the UL1482, (UM)

84-HUD and NPFA211 in the U.S.A. and the ULC S628-93 and

CAN/CSA-B365 Installation Codes in Canada.

4 7047-910C August 25, 2014

5100 I-ACC Install Guide

2 Getting Started

. Design and Installation Considerations

Before installing, determine the following:

• Type of chimney connector to be used

· single wall, 6 inch (152mm) diameter, stainless steel, or

· double wall, 6 inch (152mm) diameter, stainless steel

• Consult page 28 for clearances to combustibles

• Power outlet located close by for optional blower

B. Draft

Draft is the pressure difference needed to vent appliances

successfully. When a appliance is drafting successfully, all

combustion byproducts are exiting the home through the

chimney.

Considerations for successful draft include:

• Preventing negative pressure

• Location of appliance and chimney

o be sure that your appliance burns properly:

• Duringalowburn,the chimney draft (static pressure) should

be approximately -.04 inch water column (W.C.)

• Duringahighburnthechimneydraftshould beapproximately

-.10 inch (W.C.)

• Measure the W.C at 6 inches (152mm) above the top of the

appliance after one hour of operation at each burn setting.

NOTICE: Hearth & Home Technologies assumes no

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building, ﬁre ofﬁcials or

authorities having jurisdiction about restrictions, installation

inspection, and permits.

CAUTION

WARNING

• DO NOT CONNECT THIS UNIT TO A CHIMNEY

FLUE SERVICING ANOTHER APPLIANCE.

• DO NOT CONNECT TOANYAIR DISTRIBUTION

DUCT OR SYSTEM.

May allow ﬂue gases to enter the house.

Asphyxiation Risk.

• Installation and use of any damaged appliance.

• Modiﬁcation of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

• Operatingappliancewithoutfullyassembling allcomponents.

• Operating appliance without legs attached (if supplied with

unit).

• Do NOT Overﬁre - If appliance or chimney connector glows,

you are overﬁring.

Any such action that may cause a ﬁre hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

responsibility for the improper performance of the

appliance system caused by:

• Inadequate draft due to environmental conditions

• Downdrafts

• Tight sealing construction of the structure

• Mechanical exhausting devices

• Overdrafting caused by excessive chimney heights

• Ideal performance is with height of chimney between

14-16 feet (4.26-4.88m) measured from the base of

the appliance.

August 25, 2014 7047-910C 5

5100 I-ACC

C. Negative Pressure

Negative pressure results from the imbalance of air avail-

able for the appliance to operate properly. It can be stron-

gest in lower levels of the house.

Causes include:

• Exhaust fans (kitchen, bath, etc.)

• Range hoods

• Combustion air requirements for furnaces, water heaters

and other combustion appliances

• Clothes dryers

• Location of return-air vents to furnace or air conditioning

• Imbalances of the HVAC air handling system

• Upper level air leaks such as:

- Recessed lighting

- Attic hatch

- Duct leaks

To minimize the effects of negative air pressure:

• Install the outside air kit with the intake facing prevailing

winds during the heating season

• Ensureadequateoutdoorairforallcombustionappliances

and exhaust equipment

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the appliance

• Avoid installing the appliance near doors, walkways or

small isolated spaces

• Recessed lighting should be a “sealed can” design

• Attic hatches weather stripped or sealed

• Attic mounted duct work and air handler joints and seams

taped or sealed

• Basement installations should be avoided

D. Tools And Supplies Needed

Before beginning the installation be sure the following tools

and building supplies are available:

Reciprocating saw Framing material

Pliers High temp caulking material

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

Misc. screws and nails

1/2-3/4 in. length, #6 or #8 self-drilling screws

E. Inspect Appliance and Components

• Remove appliance and components from packaging and

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Readalltheinstructionsbeforestartingtheinstallation.

Follow these instructions carefully during the

installation to ensure maximum safety and beneﬁt.

Inspect appliance and components for damage.

Damaged parts may impair safe operation.

WARNING

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Fire Risk.

WARNING

• Negative pressure can cause spillage of combus-

tion fumes, soot and carbon monoxide.

• Appliance needs to draft properly for safety.

Asphyxiation Risk.

6 7047-910C August 25, 2014

5100 I-ACC

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.

Customer:

Date Installed:

Lot/Address:

Location of Fireplace:

Installer:

Dealer/ Distributor Phone #:

Serial #:

Model (circle one): 51I-ACC

WARNING! Risk of Fire or Explosion! Failure to install ﬁreplace according to these instructions can lead to a ﬁre or explosion.

Appliance Install

Veriﬁed clearances to combustibles. (Pg. 8)

Fireplace is leveled and liner is secured to appliance. (Pg. 18)

Hearth extension size/height decided. (Pg. 22)

Outside air kit installed. (Pg. 15)

Floor protection requirements have been met.

The masonry chimney is inspected by a professional and is clean or the

factory built metal chimney is installed according to the manufacturer’s

instructions and clearances.

Chimney Section 4 (Pg. 10)

Chimney conﬁguration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney meets the minimum height requirements.

Roof ﬂashing installed and sealed.

Terminations installed and sealed.

Clearances Section 3 (Pg. 7)

Combustible materials not installed in non-combustible areas.

Veriﬁed all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Protective hearth strips and hearth extension installed per manual requirements.

Appliance Setup Section 5 (Pg. 15)

All packaging and protective materials removed.

Firebrick, bafﬂe and ceramic blanket installed correctly.

All labels have been removed from the door.

All packaging materials are removed from inside/under the ﬁreplace.

Manual bag and all of its contents are removed from inside/under the ﬁreplace

and given to the party responsible for use and operation.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your ﬁle.

• That this checklist remain visible at all times on the ﬁreplace until the installation is complete.

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Comments communicated to party responsible by on

(Builder/Gen. Contractor) (Installer) (Date)

Part # 4017-254 • Rev B • 01/29/13

YES IF NO, WHY?

F. Install Checklist

August 25, 2014 7047-910C 7

5100 I-ACC

Figure 7.1 Top View Figure 7.2 Front View

Figure 7.3 - Side View

37-7/16 in. (951mm)

29-1/16 in. (738mm)

25-1/2 in. (648mm)

12-3/8 in.

(314mm)

17-9/16 in.

(446mm)

13-1/16 in.

(332mm)

26-11/16 in. (678mm) 9-1/8 in.

(232mm)

21-3/16 in.

(538mm)

21 in.

(534mm)

11-3/4 in.

(280mm)

30-5/8 in. (762mm)

Surround Sizes AB

Standard 43 in. (1092mm) 31 in. (787mm)

Large 51 in. (1346mm) 34 in. (864mm)

20-1/8 to 23-1/2 in.

(512 to 896mm)

15/34 to 19 in.

(399 to 483mm)

7-7/8 in.

(200mm)

Figure 7.4 - Side View With Optional Offset Adapter

3 Dimensions and Clearances

A. Appliance Dimensions NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)

8 7047-910C August 25, 2014

5100 I-ACC

NOTE: Clearances may only be reduced by

means approved by the regulatory authority

having jurisdiction

Fire Risk.

• Comply with all minimum clearances to

combustibles as speciﬁed.

• Failure to comply may cause house ﬁre.

WARNING

In Canada a full length 6 inch (152mm) S635 ﬂue liner required as per ULC S628.

In USA a minimum 5 ft length (1.82m), 6 inch (152mm) diameter ﬂue liner is required as per UL 1482.

SIDE TRIM

SIDE WALL

TOP TRIM

27-1/4

692mm

32-1/4

819mm

HEARTH

EXTENSION

USA 16-3/4

CANADA

24-3/4 (629mm)

40-11/16

1033mm

FIREPLACE FRONT SURFACE

USA 23-1/2

CANADA 25-1/2 (648mm)

HEARTH EXTENSION

43-11/16

1110mm

12in max

MANTEL

No thermal protection required

ember protection only

B. Clearances to Combustibles, United States and Canada (UL and ULC)

August 25, 2014 7047-910C 9

5100 I-ACC

Recommended

Location

Marginal

Location

Not

Recommended

Location

Location NOT

Recommended

Multi-level Roofs

Windward

Leeward

Outside Air Kit Termination Cap

Figure 9.1

D. Chimney Termination Requirements

Follow manufacturer’s instructions for clearance, securing

ﬂashing and terminating the chimney.

•Must have an approved and Listed cap

•Must not be located where it will become plugged by

snow or other material

• Must terminate at least 3 feet (91cm) above the roof

and at least 2 feet (61cm) above any portion of the

roof within 10 feet (305cm).

• Must be located away from trees or other structures

C. Locating Your Stove & Chimney

Location of the appliance and chimney will affect perfor-

mance. As shown in Figure 9.1 the chimney should:

• Install through the warm space enclosed by the build-

ing envelope. This helps to produce more draft, espe-

cially during lighting and die down of the ﬁre.

• Penetrate the highest part of the roof. This minimizes

the affects of wind turbulence and down drafts.

• Consider the appliance location in order to avoid ﬂoor

and ceiling attic joists and rafters.

•

Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

Your local dealer is the expert in your geographic area and

can usually make suggestions or discover solutions that will

easily correct your ﬂue problem.

NOTICE:

• Chimney performance may vary.

• Trees, buildings, roof lines and wind conditions affect

performance.

• Chimney height may need adjustment if smoking or

overdraft occurs.

NOTICE: Locating the appliance in a basement or in a

locationof considerable air movementcancauseintermittent

smoke spillage from appliance. Do not locate appliance near

• Frequently open doors

• Central heat outlets or returns

10 7047-910C August 25, 2014

5100 I-ACC

3 ft. (91cm)

Minimum

Less than 10 ft. (305cm)

2 ft. (61cm) 3 ft. (91cm)

Minimum

10 ft. (305cm) To Nearest Roofline

2 ft. (61cm)

Figure 10.1 Pitched Roof

Figure 10.2 Flat Roof

10 ft. (305cm) or more

3 ft. (91cm) Minimum

Less than 10 ft. (305cm)

2 ft. (61cm) Minimum

3 ft. (91cm) Minimum

Wall or Parapet

E. 2-10-3 Rule

These are safety requirements and are not meant to assure proper ﬂue draft.

This appliance is made with a 6 inch (152mm) diameter chimney connector as the ﬂue collar on the unit.

• Changing the diameter of the chimney can affect draft and cause poor performance.

• It is not recommended to use offsets and elbows at altitudes above 4000 feet above sea level and or when there

are other factors that affect ﬂue draft.

Andere Handbücher für 5100 ACC

Inhaltsverzeichnis

Andere Quadra-Fire Kamin im Innenbereich Handbücher

Quadra-Fire

Quadra-Fire Direct Vent Gas Fireplace Insert Bedienungsanleitung

Quadra-Fire

Quadra-Fire VILLAGE Series Handbuch

Quadra-Fire

Quadra-Fire SANTAFEI-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire VOYAGEUR GRAND VOYA-GRAND-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire SANTAFEI-MBK Bedienungsanleitung

Quadra-Fire

Quadra-Fire Quadra-Fire 2700-I Bedienungsanleitung

Quadra-Fire

Quadra-Fire iLLAGE QV32-A Montageanleitung

Quadra-Fire

Quadra-Fire 7100FP-GD-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire QVI-25FB-S Bedienungsanleitung

Quadra-Fire

Quadra-Fire Gas Firebrick qvi30fb Bedienungsanleitung

Quadra-Fire

Quadra-Fire EXPLORER III Series Bedienungsanleitung

Quadra-Fire

Quadra-Fire DVI-32 Bedienungsanleitung

Quadra-Fire

Quadra-Fire QV36DB-A Bedienungsanleitung

Quadra-Fire

Quadra-Fire HUDSON BAY HUDBAY-FS Bedienungsanleitung

Quadra-Fire

Quadra-Fire PELLET INSERT CB1200MI-MBK Sicherheitsleitfaden

Quadra-Fire

Quadra-Fire QVI-35FB-S Bedienungsanleitung

Quadra-Fire

Quadra-Fire HV-IPI QV-PIER Bedienungsanleitung

Quadra-Fire

Quadra-Fire VILLAGE COLLECTION Handbuch

Quadra-Fire

Quadra-Fire VOYAGEUR GRAND INSERT GRAND-MBK-AU Bedienungsanleitung

Quadra-Fire

Quadra-Fire 7100FP-GD-B Bedienungsanleitung

Quadra-Fire

Quadra-Fire COLUMBIA BAY Installationsanleitung

Quadra-Fire

Quadra-Fire VILLAGE QV26E Bedienungsanleitung

Quadra-Fire

Quadra-Fire 27I-ACC Bedienungsanleitung

Quadra-Fire

Quadra-Fire 2100-I Leitfaden

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung