10 7019-229G August 3, 2018
Santa Fe Pellet Insert
E. General Operating Information
1. Thermostat Calls For Heat
The appliance is like most modern furnaces; when the
thermostat calls for heat, your appliance will automatically
light and deliver heat. When the room is up to temperature
and the thermostat is satised, the red call light will shut
off and the appliance will shut down. The red call light is
located behind the left access panel.
2. Heat Output Controls
This appliance is equipped with a heat output control switch
that has three settings or burn rates; low, medium and high
(Figure 10.1). The appliance will turn on and off as the
thermostat demands. When the thermostat calls for heat,
the appliance will always start up on High. After burning
approximately 4 minutes, the appliance will then burn at the
rate at which it was originally set. If the appliance is set at
one of the lower settings, it will run quieter but takes longer
to heat up an area than if it were set at a higher burn rate.
Regardless of the burn rate, when the area is warm enough
to satisfy the thermostat, the appliance will shut off.
Figure 10.1
F. Before Your First Fire
1. First, make sure your appliance has been properly
installed and that all safety requirements have been
met. Pay particular attention to the re protection,
venting and thermostat installation instructions.
2. Double check that the ash drawer and rebox are
empty!
3. Check the position of the thermocouple, located
above the re pot, and make sure that it protrudes
approximately 3/4 inch (19mm) into the re pot.
4. Close the front door.
G. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance, except for corn. At this time, ll the hopper
with pellets, set the thermostat to its lowest setting.
Plug the power cord into nearby outlet.
2. The exhaust blower will stay on for approximately 18
minutes even though the thermostat is not calling for
heat. This is normal.
3. Locate the heat output control switch on the lower right
side of the rebox in front of the right access panel. Set
to the HIGH setting and then adjust the thermostat to
its highest setting. The red call light will be on which is
located on the front of the junction box behind the left
access panel. This indicates the thermostat is calling
for heat (Figure 11.1 on page 11).
4. The fuel feed system and the igniter should
now
be on.
5. For your rst re it will be necessary to press the reset
button once a minute until pellets start to drop into the
re pot, then press button 1 more time. This will ll the
feed system and allow the appliance to begin dropping
pellets. The appliance will continue to run as long as
the thermostat is calling for heat.
6. Once the appliance has ignited, let it burn for
approximately 15 minutes, then set the thermostat to
the desired room temperature. Adjust the heat output
control switch to the desired setting.
CAUTION
Tip of thermocouple must be in contact with the inside
end of the thermocouple cover.
Missed ignitions can occur.
WARNING
Fire Hazard.
Keep combustible materials, gasoline and other
ammable vapors and liquids clear of appliance.
• Do NOT store ammable materials in the appliance’s
vicinity.
• NEVER USE GASOLINE, GASOLINE-TYPE
LANTERN FUEL, KEROSENE, CHARCOAL
LIGHTER FLUID, OR SIMILAR LIQUIDS TO START
OR “FRESHEN UP” A FIRE IN THIS APPLIANCE.
KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE
APPLIANCE WHILE IT IS IN USE.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
• DO NOT USE CHEMICALS OF FLUIDS TO START
THE FIRE.
• Combustible materials may ignite.
WARNING
Fire Risk
Do NOT operate appliance:
• With appliance door open.
• Fire pot oor open.
• Cleaning slide plates open.
Do NOT store fuel:
• Closer than required clearances to
combustibles to appliance
• Within space required for loading or ash
removal.
