Quantum Networks QN-I-270 Bedienungsanleitung

Quick Setup Guide

Model: QN-I-270

Contents

Glossary....................................................................................................................................3

Icon description........................................................................................................................3

Before you begin.....................................................................................................................4

Package contents....................................................................................................................4

Prerequisites............................................................................................................................4

Network requisites...................................................................................................................4

Connect Access Point ............................................................................................................4

Step 1 –Create new account on Quantum® RUDDER....................................................5

Step 2- Basic setup.................................................................................................................6

Step 3- Setting up device IP address...................................................................................7

Step 4 –Set the management mode...................................................................................7

Step 5 - Access Point quick setup inRUDDER Mode .......................................................8

Step 6 - Access Point quick setup in standalone mode..................................................13

Reset Access Point to factory defaults..............................................................................16

Access Point default login detail.........................................................................................16

FCC statement.......................................................................................................................17

This Quick Setup Guide provides step-by-step instructions on how to set up Quantum®

Networks Access Point. After completing the steps described in this Guide, you will be able

to install the Access Point (AP) on-site and provide wireless network access to users.

Glossary

Feature

Description

Management Mode

Standalone: In this mode, each device is configured and

managed individually. It can be useful in scenarios with

few devices or sites with limited Internet access.

RUDDER: In this mode, devices are configured and

managed from a central controller hosted in the cloud. It

offers many more sets of features as compared to the

Standalone mode.

Operation Mode

Bridge: In this mode, the device connects to a network

over an ethernet cable and extends the coverage over

wireless.

Router: In this mode, the device connects to Internet

Service Provider directly using DHCP / Static IP / PPPoE

protocols and shares Internet access over a wired or

wireless network to users.

Quantum® RUDDER

Quantum® RUDDER is a cloud-hosted controller which

can be used to configure, manage & monitor devices

associated with it. It can be accessed from

https://rudder.qntmnet.com

Icon description

Icon on GUI

Description

Click to get the option for the firmware update.

Click to get back to the home page.

Click to check the documentation.

Click to check device information.

Before you begin

Your Quantum® Networks Access Point can work in “Standalone Mode” or can be

managed by “RUDDER”.

Package contents

Access Point.

Prerequisites

Internet access.

Desktop / Laptop / Handheld device.

802.3af / 802.3at PoE Switch / PoE Injector.

48VDC 2A DC power adapter.

Network requisites

The listed ports must be opened or allowed in the network firewall.

TCP: 80, 443, 2232, 1883.

UDP: 123, 1812, 1813.

Allow rudder.qntmnet.com and reports.qntmnet.com in the destination field.

Connect Access Point

After unpacking Access Point, connect it to an Internet source.

Plug-in Ethernet cable of Access Point.

Power on Access Point by using 802.3af / 802.3at PoE Switch / PoE Injector.

Note: Access Point must have Internet access during initial setup for the first time toactivate

the device, warranty and support.

Step 1 –Create new account on Quantum® RUDDER

Browse https://rudder.qntmnet.com.

Click “Create New Account” to sign up for a new account.

Figure 1

Follow the steps as guided on the screen for Registration.

Verify Quantum® RUDDER account from registered email id.

Once the account gets validated, it turns the page to “Add License Key”(User will get

the license key from respective (Partner / Resource))

Account on Quantum® RUDDER(Quantum Networks® Cloud Controller) is now ready

to use.

Step 2- Basic setup

Connect the WAN port of the Access Point to the network with Internet access.

You should see a new wireless network with SSID QN_XX:XX (where XX:XX are the

last four digits of Access Point MAC Address).

Connect to QN_XX:XX SSID and browse Access Point’s default IP “169.254.1.1”.

Figure 2

Let’s start the configuration.

On the configuration start page, it will display,

Device model number

Serial number

MAC address

Current firmware

Note:

Click button to get the option to “change the firmware” if required.

Click Change Firmware to update firmware if required. Select the firmware file from the

respective location and update it.

Step 3- Setting up device IP address

Click “Configure “and set the device IP address by selecting the required options.

Connectivity Mode –Ethernet / USB

Protocol - DHCP, Static or PPPoE

Interface –Select interface

VLAN Assignment- Enable parameter. Enter VLAN ID and click “Fetch IP Address” to

get the respective IP in case of VLAN setup is required.

Figure 3

Click “Proceed “to apply configuration and turn to the next page.

Step 4 –Set the management mode

Management Mode

Quantum® Networks Access Point can be configured in two modes:

RUDDER (on cloud / on-premise)

Centralized management of Access Points using Quantum® RUDDER

Standalone

Independent management of each Access Point

Figure 4

Step 5 - Access Point quick setup inRUDDER Mode

Select “Management Mode” as “RUDDER”, enter Quantum® RUDDER login

credentials and click “Proceed”.

Figure 5

In the case of on-premise RUDDER,

mention the local server IP Address/URL

assigned to RUDDER, here.

It will verify the credentials, and turn to a next page.

Figure 6

Upgrade QNOS version by either downloading from the cloud or by selecting manually

from respective location and upgrade orclick “Skip Upgrade” to move further.

The user will turn to a page where the user has to select the site and AP group.

Figure 7

Select RUDDER site and AP Group where Access Point’s needs to be added and click

“Proceed”.

oIf the selected site is already having another Access Point, it will automatically configure

AP in a bridge mode and will turn the user on the summary page after clicking

“Proceed”. (Figure 8)

oIf this is the first Access Point for the selected site –the user will turn on the page, where

the user can select Access Point Operation mode as Bridge or Router. (Figure 9)

Figure 8 Figure 9

Bridge

Select option Bridge and click “Proceed”.

Configure WLAN (SSID) parameters and click “Proceed”.

Parameter

Value

WLAN Name

Define a name for the network

SSID

Define visible wireless network name

Passphrase

Configure a passphrase for SSID

Figure 10

Note: If you do not want to create WLAN

(SSID)/LAN now, click the Skip option. It

willturn to Configuration Summary.

Inhaltsverzeichnis

Andere Quantum Networks Drahtloser Zugangspunkt Handbücher

Quantum Networks

Quantum Networks QN-I-200 Bedienungsanleitung

Quantum Networks

Quantum Networks QN-H-245 Bedienungsanleitung

Quantum Networks

Quantum Networks QN-I-200 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung