Quantum DLTtape DLT1 Bedienungsanleitung

DLT™1/7 TAPE UNIT INSTALLATION

Digital Unix 4.0;

IBM RISC System/6000 must have the appropriate SCSI interface for DLT drive to attached to, i.e., a SCSI

single-ended DLT drive can be attached only to a SCSI single-ended interface. The same is true for SCSI

differential attachment. After the DLT tape peripheral has been attached, you will need to perform certain

system operations that allow the DLT tape peripheral to be recognized.

Adding device definitions

Digital UNIX version 4.0 uses Dynamic Device Recognition to simplify adding support for

a new SCSI device. Adding a new device is a three-step process:

1. Use the ed, vi, or jot editor to add or modify a tape drive definition in the

/etc/ddr.dbase file. This file contains sections for each device definition. Adding a

new device definition is usually as easy as copying and pasting information from a

similar device and making one or two modifications.

2. Make the new definition(s) known to the system by issuing the command ddr_config

c /etc/ddr.dbase.

3. (optional) Generate the device files by running /dev/MAKEDEV for the added device.

When these steps are complete, your system is ready to use the new tape drive. You do not

need to reboot. If the new tape drive does not operate as youexpect, you can repeat the

above steps to modify the definition until the device operates correctly.

Procedure for modifying the device definitions

Note: The device definitions in this document are for Digital UNIX version

4.0a. Later versions may contain slightly different default entries in the

/etc/ddr.dbase file.

Follow these steps to add a new tape drive to the /etc/ddr.dbase file:

Important: Always create a backup copy of the file before you modify it.

4. Login with root privileges.

5. Go to the /etc directory:

6. cd /etc

7. Make a backup copy of the original ddr.dbase file:

8. cp /etc/ddr.dbase /etc/ddr.dbase.orig

9. Edit the ddr.dbase file to add the new tape drive. See the following sections for the

required modifications for each type of Exabyte tape drive.

10. vi ddr.dbase

11. Save the changes to the file:

12. :w!

13. Go to the /dev directory:

14. cd /dev

15. Create device files for the new tape drive:

16. MAKEDEV [id]

Where [id] is the SCSI ID of the new tape drive. For example, MAKEDEV tz5 creates device

files for a tape drive at SCSI ID 5.

Assuming that no device files were previously created for any tape drives, the MAKEDEV

command creates the following eight device files in the /dev directory:

/dev/rmt0l Low density rewinding device

/dev/rmt0h High density rewinding device

/dev/rmt0m Medium density rewinding device

/dev/rmt0a Alternate density rewinding device

/dev/nrmt0l Low density non-rewinding device

/dev/nrmt0h High density non-rewinding device

/dev/nrmt0m Medium density non-rewinding device

/dev/nrmt0a Alternate density non-rewinding device

Your system is now ready to use the new tape drive.

You need to create device files for each tape drive only once. If you add more than one tape

drive, the next time you run MAKEDEV, it will create /dev/[n]rmt1[lhma], then

/dev/[n]rmt2[lhma], and so on for the additional tape drives.

Modifications for DLT1 tape drives

# ####################################################################

# TAPES:

# ####################################################################

# The "default" tape entry is as follows:

# PARAMETERS:

# TypeSubClass = rdat

# BlockSize = 0

# MaxTransferSize = 0xFFFFFF # 16MB-1 tape default

# BadBlockRecovery = disabled

# SyncTransfers = enabled

# DynamicGeometry = false

# Disconnects = enabled

# TaggedQueuing = enabled

# CmdReordering = disabled

# LongTimeoutRetry = disabled

# DisperseQueue = true

# WideTransfers = enabled

# WCE_Capable = false

# PwrMgmt_Capable = true

# Additional_Flags = 0x0

# TagQueueDepth = 32

# ReadyTimeSeconds = 300 # seconds

# CMD_PreventAllow = notsupported

# CMD_ExtReserveRelease = notsupported

# CMD_WriteVerify = notsupported

# Additional_Cmds = 0x0

# InquiryLength = 36

# RequestSenseLength = 64

# DENSITY:

# #

# DensityNumber = 0,1,2,3,4,5,6,7

# DensityCode = default

# Buffered = 0x1

# ####################################################################

SCSIDEVICE

# Matches DLT1

Type = tape

Name = "QUANTUM" "DLT7000"

PARAMETERS:

TypeSubClass = tk

TagQueueDepth = 0

MaxTransferSize = 0x0ffffff # (16MB - 1)

ReadyTimeSeconds = 120 # seconds

DENSITY:

DensityNumber = 0

DensityCode = 0x86

CompressionCode = 0x0

Buffered = 0x1

DENSITY:

DensityNumber = 1

DensityCode = 0x40

CompressionCode = 0x0

Buffered = 0x1

DENSITY:

DensityNumber = 2,4,5,6,7

DensityCode = 0x87

CompressionCode = 0x0

Buffered = 0x1

DENSITY:

DensityNumber = 3

DensityCode = 0x7f

CompressionCode = 0x0

Buffered = 0x1

DLT Mini-Library Usage

The Solaris operating system does not support SCSI-2 media changer device commands. Therefore, an

installed DLT™7 mini-library can not be utilized in random access mode and can only be accessed in

sequential mode. Refer to the DLT1/DLT7 Install and Operations Guide manual for detailed description of

these access modes.

Andere Handbücher für DLTtape DLT1

Dieses Handbuch passt für folgende Modelle

Andere Quantum Lagerung Handbücher

Quantum

Quantum Tape Drive A-Series Bedienungsanleitung

Quantum

Quantum DAT 72 Bedienungsanleitung

Quantum

Quantum DLT-V4 Bedienungsanleitung

Quantum

Quantum QX Series Bedienungsanleitung

Quantum

Quantum LTO-6 Bedienungsanleitung

Quantum

Quantum LTO-4 (Model B) Bedienungsanleitung

Quantum

Quantum Internal Storage System Travan 40 GB Bedienungsanleitung

Quantum

Quantum Scalar i500 Bedienungsanleitung

Quantum

Quantum Scalar i40 Bedienungsanleitung

Quantum

Quantum Atlas II Service-Handbuch

Quantum

Quantum SuperLoader DLT Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Installations- und Betriebshandbuch

Quantum

Quantum DLT-V4 Bedienungsanleitung

Quantum

Quantum DAT 160 Bedienungsanleitung

Quantum

Quantum StorNext AEL500 Bedienungsanleitung

Quantum

Quantum DXi2500-D Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum ActiveScale P100E3 Bedienungsanleitung

Quantum

Quantum DLT-V4 Bedienungsanleitung

Quantum

Quantum Scalar 50 Bedienungsanleitung

Quantum

Quantum Scalar i6000 Bedienungsanleitung

Quantum

Quantum Scalar i6000 Technisches Handbuch

Quantum

Quantum ValueLoader DLT VS160 Bedienungsanleitung

Quantum

Quantum LTO 1U Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung