Quantum Scalar i6000 Gebrauchs- und Pflegehandbuch

6-67999-01 Rev A, October 2013 *6-67999-01 A*

Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates

in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum

specifications are subject to change.

Quantum Scalar i6000 Drive

Replacement

Use this procedure to replace a tape drive in a Scalar i6000 library.

If a drive fails, the library will issue a ticket. From the Details screen, write down

the Repair Link or Error Code number. You’ll need it when you contact

Quantum Service.

WARNING: Before performing any of the steps listed in this document,

contact Quantum Service for help diagnosing the problem.

WARNING: To use this procedure, all drives must be connected to an Ethernet

Expansion Blade (EEB) or an FC I/O blade.

Refer to the following sections and follow the steps in the document to replace

a drive in your Scalar i6000 library:

•Locating a Drive on page 2

•Remove and Replace the Drive on page 4

•Update the Drive Firmware Using Firmware Images on page 8

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

2 Locating a Drive

Locating a Drive

When a drive fails, a ticket is generated by the library that will identify the

malfunctioning drive using a coordinate system. This section will explain the

basics of locating a drive using the coordinate system so when you are replacing

the drive, you will be able to identify the correct drive. Removing a drive

incorrectly can impact data on your library.

The drive coordinate system has six (6) numbers, for example: 1, 2, 1, 7, 1, 1.

The first number identifies the aisle. The Scalar i6000 is a single aisle library only

so this number is always 1.

The second number identifies the module. The module number can be from 1-

16. This applies to both single- and dual-robot libraries. The left parking module

(module 0) is only for dual-robot libraries and cannot contain drives. A high-

density expansion module (HDEM) also cannot contain drives.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

Locating a Drive 3

The third number in the sequence represents the rack. Since drives can only be

contained in rack 1, this number will always be 1.

The fourth number indicates the section. Each module can contain 12 drives so

with drives, this number can range from 1-12. Drives are counted from bottom

to top.

The fifth number in the sequence identifies the column. Since drives can only be

contained in a single column, they will always reside in column 1.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

4 Remove and Replace the Drive

The sixth number denotes the row and will always be 1. Drives have a

connection point at the lower portion of the drive sled that connects to the

library. Therefore, the sled is logically in row 1.

Remove and Replace the Drive

Note: This procedure is used to replace a drive with the same drive model.

Drive upgrades must be performed by Quantum service personnel. If

the failed drive is an EDLM drive, it must be replaced by Quantum

service personnel.

Caution: Before starting this procedure, verify that you have received the

same make and model drive as the drive you are replacing. The

outside of the box will indicate the drive make and model that was

shipped.

Required tool: Phillips screwdriver - use this if the thumbscrews are too tight

1Stop any processes on the host that are communicating with the drive that

is being replaced.

2Log on as the administrator from the library’s touch screen (LMC).

3Locate the drive identified as needing replacement on your call with

Quantum Service:

aSelect View > Physical Library.

bSelect Tools > Drives. The Drives screen displays.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

Remove and Replace the Drive 5

cUsing the coordinates, select the drive to be replaced.

dScroll over to the Firmware Version column.

eWrite down the four digit firmware level.

4Click Cancel to close the Drives screen.

5Double check that there is no tape in the drive you are removing. If there is

a cartridge in the tape drive:

aSelect View > Partition. You will select the partition that contains the

drive you are replacing.

bSelect Operations > Drives > Unload. This will eject the tape from the

drive and return it in its storage slot in the library.

Note: If a tape is in the drive and cannot be ejected, call Quantum

support before proceeding.

6Go back to library view by selecting View > Physical Library.

7Select Tools > Drives. The Drives screen displays.

8Vary off the drive:

aFrom the Drives screen, use the Drive Type drop-down menu to display

the drives by drive type.

bSelect the drive, and then click Vary Off.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

6 Remove and Replace the Drive

cClick Yes.

dGo to the rear of the module containing the drive to be replaced, open

the back door, locate the drive using the coordinates from the ticket and

observe the blue LED on the rear of the drive. When the blue LED stops

blinking and remains constantly lit, you can continue.

Guide Rail

Thumbscrews

Blue LED

Green Port LED 1

Amber LED

Green LED 2

Drive Handle

9Disconnect all cables from the drive. Note which cables go to which

connections for reference during drive replacement.

10 Loosen the two thumbscrews on the drive.

11 Grip the drive handle and pull the drive toward you to remove it.

12 Use the guide rails on the replacement drive to slowly slide it in until flush.

13 Tighten the two thumbscrews.

14 Reconnect the cables.

15 Confirm the following status LEDs:

aBlue LED light on the back of the drive is constantly lit

bGreen LED 2 light on the back of the drive is blinking slowly and in

cadence with the LEDs on the other drives

Note: The LEDs should take less than 5 minutes to get to this state.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

Remove and Replace the Drive 7

16 If the LEDs are displaying properly, you can vary on the drive. From the

Drives screen:

aSelect the newly installed drive.

bClick the Vary On button.

cClick Cancel.

17 The library may update the drive sled firmware. Wait a few minutes to see if

a dialog box appears. If this happens, wait until it is complete before

continuing. The drive sled firmware update will take approximately 5

minutes.

18 Go to the rear of the module and observe the drive status LEDs and wait for

the following conditions to occur:

•Green LED 1 - solid green indicating port connectivity to either the

FC I/O blade or the customer FC switch

•Amber LED - off

•Blue LED - blinks one time per 10 seconds

•Green LED 2 - blinks at the same cadence as the other green LEDs on

the other drives in the module

Blue LED

Green Port LED 1

Amber LED

Green LED 2

19 Close the access doors.

20 Close the ticket that was generated for the failed drive.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

8 Update the Drive Firmware Using Firmware Images

Update the Drive Firmware Using Firmware Images

Note: This procedure should only be used if drive auto-leveling is turned off.

Note: If you are viewing a partition, drive firmware update operations affect

drives that are within the partition only.

Note: You can only perform firmware updates for drives of the same product,

such as IBM LTO-4 or HP LTO-5.

Caution: If you load a firmware image onto a drive that is the same version

that is currently running on the drive, the upgrade will fail.

1From the View menu, select the partition that contains the replacement

drive.

2Select Tools > Update Software > Drives. A warning dialog box displays

stating the partition needs to be taken offline.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

Update the Drive Firmware Using Firmware Images 9

3Click Yes.

4From the Update Drive Firmware screen, ensure the option selected in the

Update Method area is set to Firmware Image.

5Click the check box next to the replacement drive.

6Compare the four digit firmware level you wrote down earlier with the four

digit firmware version listed in the Firmware column of the selected drive. If

they match, go to step 12. If not, continue on to step 7.

7From the Select Firmware File drop-down menu, select the firmware image

you want to install.

The drop-down list includes all drive firmware images that are currently

stored on the library, regardless of drive type. Be careful to select a drive

firmware image that is compatible with the type of drive that you want to

update. See the library's Release Notes for compatibility information or

contact Quantum technical support.

For details on downloading drive firmware, see Chapter 15, Maintaining

Your Library - Maintenance Actions in the Scalar i6000 User’s Guide.

8Click Start. A warning dialog box displays stating the operation cannot be

canceled.

9Click Yes. The library automatically logs off other users so they cannot

perform library operations while the drive firmware update is in progress.

Quantum Scalar i6000: Drive Replacement

6-67999-01 Rev A

October 2013

10 Update the Drive Firmware Using Firmware Images

Note: On the back of the drive, the Green LED 2 will flash rapidly while

the firmware update is in progress.

10 The library updates the firmware on the selected drive.

Note: Updating drive firmware could take up to 20 minutes to complete.

11 When finished, the Status column of the drive will state Update Complete

and the LEDs on the back of the drive will display:

•Green LED 1 - solid green indicating port connectivity to either the

FC I/O blade or the customer FC switch

•Amber LED - off

•Blue LED - blinks one time per 10 seconds

•Green LED 2 - blinks at the same cadence as the other green LEDs on

the other drives in the module

12 Click Close.

13 Select View > Views. The Manage Views screen displays.

14 Click the Offline button for the partition that contains the replacement

drive. The Change Library Mode screen displays.

15 In the Mode area on the Change Library Mode screen, select Online and

click OK. The Manage View dialog shows the partition now Online.

16 Click Close.

Andere Handbücher für Scalar i6000

Andere Quantum Lagerung Handbücher

Quantum

Quantum DLTtape SDLT 220 Handbuch

Quantum

Quantum SNC 4000 Bedienungsanleitung

Quantum

Quantum LTO 4 Bedienungsanleitung

Quantum

Quantum Scalar i500 Bedienungsanleitung

Quantum

Quantum PX500 Series Kurzanleitung

Quantum

Quantum Quantum Atlas 10K II 9.2/18.4/36.7/73.4 GB Bedienungsanleitung

Quantum

Quantum DAT 72 Bedienungsanleitung

Quantum

Quantum DLTtape SDLT 600 Bedienungsanleitung

Quantum

Quantum DLTtape DLT 4000 Bedienungsanleitung

Quantum

Quantum Scalar 50 Bedienungsanleitung

Quantum

Quantum DX100 Bedienungsanleitung

Quantum

Quantum LTO-6 Bedienungsanleitung

Quantum

Quantum DXi4510 Bedienerhandbuch

Quantum

Quantum Scalar i500 Bedienungsanleitung

Quantum

Quantum DXi4520 Bedienerhandbuch

Quantum

Quantum LTO-4 (Model B) Bedienungsanleitung

Quantum

Quantum StorNext M330 Montageanleitung

Quantum

Quantum Scalar i2000 Bedienungsanleitung

Quantum

Quantum Scalar i6000 Technisches Handbuch

Quantum

Quantum ValueLoader DLT VS160 Betriebsanleitung

Quantum

Quantum Scalar LTFS Gebrauchs- und Pflegehandbuch

Quantum

Quantum PX500 Series Kurzanleitung

Quantum

Quantum DXi4510 Bedienerhandbuch

Quantum

Quantum DLTtape SDLT 600 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung