Quantum Scalar LTFS Gebrauchs- und Pflegehandbuch
6-68096-01 Rev A, December 2013 *6-68096-01 A*
© 2013 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader,
Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates
in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum
specifications are subject to change.
Quantum Scalar LTFS
Appliance:
Rail Replacement
To replace the rails in your Scalar Linear Tape File System (LTFS) Appliance, refer
to the following sections:
•Turning Off the Scalar LTFS Appliance on page 1
•Preparing To Remove the Scalar LTFS Appliance on page 2
•Removing the Chassis and Rails From the Rack on page 2
•Replacing the Rails in the Rack on page 3
•Reinstalling the Chassis in the Rack on page 5
•Turning On the Scalar LTFS Appliance on page 7
Turning Off the Scalar LTFS Appliance
Follow these steps to cleanly shut down and power off the Scalar LTFS Scalar
LTFS Appliance:
1Open an ssh connection to the Scalar LTFS Appliance, and log in as the
service user:
• User: service
• Password: The customer-supplied password.
2Enter sudo rootsh.
3Enter the password for the service user account a second time.
4Enter /sbin/poweroff.
Both the operating system and the system software are gracefully shut
down, and then the system powers off.
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
2 Preparing To Remove the Scalar LTFS Appliance
Preparing To Remove the Scalar LTFS Appliance
Before removing any part, do the following:
• Obtain the required tools:
• #2 PHILLIPS®screw driver
• Materials for labeling cables
• Request the assistance of another person to help you.
WARNING: Whenever you need to lift the Scalar LTFS Appliance, get others to
assist you. To avoid injury, do not attempt to lift the Scalar LTFS
Appliance by yourself. The Scalar LTFS Appliance weighs 57.54
pounds (26.1 kg). Two people are required to lift the unit
Note: You will be replacing only the damaged rails (chassis rails or rack rails)
and not the entire rackmount.
Removing the Chassis and Rails From the Rack
To remove the Scalar LTFS Appliance chassis from the rack, complete the
following steps:
Note: Before you begin this procedure, be sure you powered down the Scalar
LTFS Appliance (see Turning Off the Scalar LTFS Appliance on page 1).
1Label the cables so that you can reconnect them to the correct ports.
2Remove all power, SAS, Ethernet, and Fibre Channel cables from the back of
the Scalar LTFS Appliance.
3Hold the power button in at least 20 seconds to discharge all of the
condensers before opening the Scalar LTFS Appliance.
4Remove the PHILLIPS screws that are securing the Scalar LTFS Appliance to
the front of the rack.
5Press the slide-release lock button on both rails and slide the system from
the rack (see Figure 1).
6Lift up slightly to remove the Scalar LTFS Appliance out of the rail J-slots and
place it on a flat surface.
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
Replacing the Rails in the Rack 3
Figure 1 Pulling the Scalar LTFS
Appliance From the Rack
Chassis
Rack rails
Chassis rail
7To remove the rails, pull the latch release button on the end piece midpoint
and unseat each rail.
Replacing the Rails in the Rack
To replace the rails in the rack, complete the following steps:
Note: When replacing the rails refer to Figure 2 on page 4 for square holes
and Figure 3 on page 5 for round holes.
1Position the left and right rail end pieces labeled FRONT facing inward and
orient each end piece to seat in the holes on the front side of the vertical
rack flanges.
2Align each end piece in the bottom and top holes of the desired U spaces.
3Engage the back end of the rail until it fully sets on the vertical rack flange
and the latch locks into place.
4Repeat Step 1 through Step 3 to position and seat the front end piece on
the vertical rack flange.
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
4 Replacing the Rails in the Rack
Figure 2 Installing the Tool-less
Rails (Square Holes)
Rail teeth
Release
button
Rail pegs
Front side of rack rails
Second tooth engaged
Back of rack
Release
button
Front of rack
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
Reinstalling the Chassis in the Rack 5
Figure 3 Installing the Tool-less
Rails (Round Holes)
Rail teeth
Release
button
Rail pegs
Front side of rack rails
Second tooth
engaged Back of
rack
Release
button
Front of rack
Note: When using round hole rails, the Scalar LTFS Appliance may protrude
from the rack by approximately 1/8 inch (0.3175 cm).
5Place the Scalar LTFS Appliance on a level surface and align the four J-slots
on the chassis rails with the corresponding pins on the system. Slide the
chassis rails towards the back of the system until each one locks into place
(see Figure 4 on page 6)
Reinstalling the Chassis in the Rack
To reinstall the Scalar LTFS Appliance chassis back into the rack, complete the
following steps:
WARNING: Ensure that the system is properly supported until the chassis rails
are locked into the slide rails on both sides.
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
6 Reinstalling the Chassis in the Rack
WARNING: The Scalar LTFS Appliance weighs 37.3 lbs (16.9 KG). Two people
are required to lift the chassis.
1Pull the inner slide rails out of the rack until they lock into place.
2Locate the rear rail standoff on each side of the Scalar LTFS Appliance and
lower them into the rear J-slots on the slide assemblies.
3Rotate the Scalar LTFS Appliance downward until all the rail standoffs are
seated in the J-slots.
4Push the Scalar LTFS Appliance inward until the lock levers click into place.
5Press the slide-release lock button on both rails and slide the system into the
rack.
Note: Figure 4 shows nodes with the bezel; however, the bezel is actually
added after the components are installed in the rack.
Figure 4 Installing the Chassis
in a Rack
Chassis Rails
Front
Back
Server-to-rail latch
Slide Release
Lock button
6Insert and tighten the PHILLIPS screws that secure the Scalar LTFS Appliance
to the front of the rack.
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
Turning On the Scalar LTFS Appliance 7
7Re-attach all power, SAS, Ethernet, and Fibre Channel cables to the back of
the Scalar LTFS Appliance.
Turning On the Scalar LTFS Appliance
To turn the Scalar LTFS appliance back on: Push once on the power button
located on the front of the Scalar LTFS Appliance (see Figure 5).
Reviewers: Are there any other steps to powering on the LTFS?
Figure 5 Scalar LTFS Scalar LTFS
Appliance Power Button
Power Button
Quantum Scalar LTFS Appliance: Rail Replacement
6-68096-01 Rev A
December 2013
8 Turning On the Scalar LTFS Appliance
Inhaltsverzeichnis
Andere Quantum Lagerung Handbücher
Quantum
Quantum PX502 Bedienungsanleitung
Quantum
Quantum StorNext QD7000 Bedienungsanleitung
Quantum
Quantum FIREBALL PLUS AS 10.2 Bedienungsanleitung
Quantum
Quantum Scalar 218FC Bedienungsanleitung
Quantum
Quantum Scalar i6000 Bedienungsanleitung
Quantum
Quantum Quantum Atlas 10K II 9.2/18.4/36.7/73.4 GB Bedienungsanleitung
Quantum
Quantum DLTtape SDLT 600 Bedienungsanleitung
Quantum
Quantum StorNext QM1200 Bedienungsanleitung
Quantum
Quantum Scalar i6000 Bedienungsanleitung
Quantum
Quantum Scalar i40 Bedienungs- und Sicherheitshinweise
Quantum
Quantum FastStor 1 Bedienungsanleitung
Quantum
Quantum StorNext QM1200 Bedienungsanleitung
Quantum
Quantum LTO-4 (Model B) Bedienungsanleitung
Quantum
Quantum Maxtor Fireball lct10 Bedienungsanleitung
Quantum
Quantum DLTtape SDLT 600 Bedienungsanleitung
Quantum
Quantum Bigfoot 1.2AT Bedienungsanleitung
Quantum
Quantum LTO 3 Bedienungsanleitung
Quantum
Quantum LTO 4 Bedienungsanleitung
Quantum
Quantum ATL StackLink Bedienungsanleitung
Quantum
Quantum DLT-S4 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung