Quantum StorNext QM1200 Bedienungsanleitung

StorNext QM1200, QS1200 or QS2400 Base System

Replacing a Controller

6-68012-01 Rev B *6-68012-01 B*

ii Replacing a Controller

StorNext QM1200, QS1200 or QS2400 Base System, Replacing a Controller, 6-68012-01 Rev B, April 2015, Product of

USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including

but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation

may revise this publication from time to time without notice.

Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written

authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Quantum, the Quantum Logo, Backup. Recovery. Archive. It's What We Do., Be Certain, Be Quantum Certain, DLT, the DLT

Logo, DLTSage, DLTtape, the DLTtape Logo, DXi, DXi Accent, Dynamic Powerdown, FastSense, FlexLink, GoProtect,

GoVault, iLayer, Lattus, MediaShield, Optyon, Pocket-sized., Well-armored., Preserving the World's Most Important Data.

Yours., Q-Cloud, Quantum Certain, Quantum Certainty, Quantum vmPRO, Scalar, SDLT, SiteCare, SmartVerify,

StorageCare, StorNext, Super DLTtape, SuperLoader, and Vision are either registered trademarks or trademarks of

Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property

of their respective owners.

Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their

respective companies. All other brand names or trademarks are the property of their respective owners.

Quantum specifications are subject to change.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 1 -

Replacing a Controller in the StorNext QM1200, QS1200 or QS2400

Base System

Use this procedure to replace a controller in the StorNext QM1200, QS1200 or QS2400 Base System. Read through all

of the following steps in this procedure before you start to replace the controller canister.

You can determine whether you have a failed controller in two ways:

The Recovery Guru directs you to replace a failed controller.

You locate the failed controller by checking the Controller Service Action Required LED.

Before you start to replace a controller in the base system, gather antistatic protection, a new controller, and a

controller air blocker.

When you install a new controller, you must remove the battery from the failed controller, and install it in the new

controller. This procedure includes that task. If you are changing your current configuration, you might need to

replace these items:

Small Form-factor Pluggable (SFP) transceivers.

Host bus adapters or host channel adapters.

Cables – InfiniBand uses copper cable, and Fibre Channel uses copper cable or fiber-optic cable.

Preparing to Remove the Controller

1. Gather support data about your storage array by using one of these methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a

location on your system where you want to store the support bundle.

ATTENTION Possible hardware damage – If you perform this procedure with the power turned on, the

equipment might overheat if the controller slot is left open for more than three minutes. To prevent the

possibility of overheating, you must insert the controller air blocker into the empty controller slot when you

service the controller.

ATTENTION Loss of data access – If the controller that you are replacing manages any secure volumes, the

new controller will need the correct security key to manage those volumes. After you replace the controller

and restore power to the base system, you can use the SANtricity® ES Storage Manager to import the key from

the file in which it was saved. Be sure that such a file exists and that you know the pass phrase required to

install the security key before you replace the controller.

ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper

antistatic protection when handling tray components.

ATTENTION Possible extended outage – You must replace the controller with the power turned on to

ensure auto-code synchronization of the native controller firmware to the new controller and to prevent the

possibility of an extended outage.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 2 -

—Use the command line interface (CLI) to run the save storageArray supportData command to

gather comprehensive support data about the storage array. For more information about this command,

refer to Command Line Interface and Script Commands. Running this command can temporarily impact

performance on your storage array.

2. Did the Recovery Guru direct you to replace a failed controller?

—Yes – Go to step 3.

—No – Run the Recovery Guru to identify the failed component, and go to step 3.

3. Put on antistatic protection.

4. Unpack the new controller.

a. Set the new controller on a flat, static-free surface near the base system with the top cover up.

b. Save all the packing materials in case you need to return the controller.

Locating the Failed Controller

1. Locate the failed controller by checking the Controller Service Action Required LEDs.

2. Refer to Figure 1 for a close-up view of the controller LEDs.

Figure 1 Pikes Peak Controller LEDs

1. Host Link 1 Service Action Required LED (Amber)

2. Host Link 2 Service Action Required LED (Amber)

3. Battery Service Action Required LED (Amber)

4. Controller Service Action Allowed LED (Blue)

5. Controller Service Action Required LED (Amber)

NOTE If a fault is detected, the amber Controller Service Action Required LED is on (Figure 2). If you can safely remove the controller

canister, the blue Controller Service Action Allowed LED is on.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 3 -

Figure 2 Controller Service Action LEDs

1. Controller Service Action Allowed LED (Blue)

2. Controller Service Action Required LED (Amber)

Pre-Work before Removing the Failed Controller

1. Label each copper cable or fiber-optic cable that is attached to the controller so that you can reconnect each

cable correctly after the new controller is installed.

2. Record the information from the seven-segment display on the rear of the base system.

The display flashes a sequence of codes. To find information about the displayed diagnostic codes, refer to

StorNext Q-Series Storage Install Guide.

Use either the GUI (first bullet) or the CLI (second bullet) to take the appropriate controller offline.

—From the Hardware pane in the Array Management Window, right-click the picture of the controller that you

want to take offline, and select Advanced >> Place >> Offline.

—Run the following command.

SMcli <DNS-network-name-or-IP-address> -c “set controller [(a | b)]

availability=offline”;

If necessary, wait for the Controller Service Action Allowed LED to come on (see Figure 2). This indication might

take several minutes for a large configuration.

3. Disconnect all of the interface cables and Ethernet cables from the failed controller.

If the storage array is running while you perform this replacement, do not disturb the second controller.

ATTENTION Potential degraded performance – To prevent degraded performance, do not twist, fold,

pinch, or step on the cables. Many cables have a minimum bending radius. For example, do not bend

fiber-optic cables tighter than a 5-cm (2-in.) radius. Check the specifications for your cables, and do not

bend any cable tighter than the minimum specified radius.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 4 -

Removing the Failed Controller

1. Prepare the controller air blocker (Figure 3) by removing it from its packaging and folding it inward at right angles

so it is ready to insert into the open controller slot.

Figure 3 Controller Air Blocker

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 5 -

2. Remove the failed controller (Figure 4).

a. Unlock and pull out the release lever to release the controller.

b. Using the release lever and your hands, pull the controller out of the base system.

Figure 4 Removing and Replacing a Controller

1. Release Lever

2. Controller

3. Set the failed controller on a flat, static-free surface with the release levers up.

4. Insert the controller air blocker (Figure 5) into the open controller slot to make sure that correct airflow is

maintained.

ATTENTION Possible equipment damage – The controller slot cannot remain open for more than three

minutes because of the possibility of overheating the equipment. The controller air blocker fills the

controller slot so that the equipment will not overheat.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 6 -

Figure 5 Inserting the Controller Air Blocker into the Open Controller Slot

Removing Battery (Move from Failed to Serviceable Controller)

1. On the failed controller (Figure 6), press down on both of the top cover latch buttons, and slide the top cover to

the rear. Remove the top cover.

Figure 6 Controller Top Cover Latch Buttons

1. Top Cover Latch Buttons

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 7 -

2. Locate the battery within the controller (Figure 7).

Figure 7 Battery and Locking Handle in the Controller

1. Top Cover Latch Buttons

2. Battery Circuit Board

3. Battery Latch

3. On the failed controller with the battery, perform these steps:

a. Release the latch that secures the battery to the controller.

b. Remove the battery by sliding it towards the rear of the failed controller.

c. Lift the battery slightly upward as you slide it to the rear of the failed controller.

NOTE You will insert this battery into the new controller.

4. If Small Form-factor Pluggable (SFP) transceivers are present, record the ports in which they are installed, and

remove them.

5. Insert the battery that you removed from the failed controller into the serviceable controller.

a. Slide the battery from the back of the controller toward the front.

b. Insert the battery at a slight downward angle into the controller canister.

StorNext QM1200, QS1200 or QS2400 Base System - Replacing a Controller April 2015

Quantum Corporation

- 8 -

c. Slide the battery towards the front of the controller canister, making sure that the battery slides under the

side guide pins to correctly seat it against the back surface of the controller.

6. Engage the latch to secure the battery circuit board in the new controller card.

7. Reinstall the top cover on the new controller by sliding it forward until the top cover latch buttons click.

Installing a Controller in the StorNext QM1200, QS1200 or QS2400 Base System

1. Remove the controller air blocker from the controller slot.

2. Slide the new controller (Figure 8) all the way into the base system. 

Push the release lever towards the center of the controller to lock it into place.

Figure 8 Installing the Controller

1. Release Lever

2. Controller

ATTENTION Make sure that the battery is fully seated and that the connectors are fully seated. If the

battery is not correctly seated, you cannot reinstall the top cover on the controller canister as directed

later. To make sure that the controller battery is seated correctly, you might need to slide it out and insert

it again. You know it is secure when you hear it click into place, and the locking handle does not move out

of its upright position when you wiggle it.

Andere Handbücher für StorNext QM1200

Dieses Handbuch passt für folgende Modelle

Andere Quantum Lagerung Handbücher

Quantum

Quantum QXS-312 Technisches Handbuch

Quantum

Quantum StorNext QS1200 Technisches Handbuch

Quantum

Quantum LTO 3A Bedienungsanleitung

Quantum

Quantum LTO-4 (Model B) Bedienungsanleitung

Quantum

Quantum DLTtape DLT 4000 Bedienungsanleitung

Quantum

Quantum Scalar 100 Bedienungsanleitung

Quantum

Quantum Scalar LTFS Stücklistenhandbuch

Quantum

Quantum DLTtape DLT 7000 Bedienungsanleitung

Quantum

Quantum P2000 Series Bedienungsanleitung

Quantum

Quantum DXi9000 Bedienungsanleitung

Quantum

Quantum Superloader 3 Bedienungsanleitung

Quantum

Quantum DLT-S4 Bedienungsanleitung

Quantum

Quantum Fireball Plus AS Bedienungsanleitung

Quantum

Quantum ValueLoader DLT VS80 Betriebsanleitung

Quantum

Quantum P1000 Series Bedienungsanleitung

Quantum

Quantum LTO3 A-Series Bedienungsanleitung

Quantum

Quantum DLT-V4 Bedienungsanleitung

Quantum

Quantum Maxtor Fireball lct10 Bedienungsanleitung

Quantum

Quantum LTO 4 Bedienungsanleitung

Quantum

Quantum PowerStor L200 Bedienungsanleitung

Quantum

Quantum DXi4601 Bedienungsanleitung

Quantum

Quantum LTO-4 (Model B) Bedienungsanleitung

Quantum

Quantum Scalar 24 Bedienungsanleitung

Quantum

Quantum DXi4700 Installations- und Betriebshandbuch

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung