Quantum StorNext QD6000 Bedienungsanleitung
Replacing a Controller
StorNext QD6000/QD7000 Base System
6-68478-01 Rev A *6-68478-01 Rev A
ii Replacing a Controller
StorNext QD6000/QD7000 Base System, Replacing a Controller, 6-68478-01 Rev A, July 2016, Product of USA.
©2016 All rights reserved. Quantum, the Quantum logo, DXi, Scalar and StorNext are registered trademarks of
Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the
property of their respective owners.
About this guide iii
About this guide
NOTE: The Lancaster firmware is used on the E5600, Titan RAID controller, only. Refer to the NetApp
to Quantum Naming Decoder section for additional information.
This section provides the following information:
•Intended audience
•Prerequisites
•NetApp to Quantum Naming Decoder
Intended audience
This guide is intended for storage customers and technicians.
Prerequisites
Prerequisites for installing and using this product include knowledge of:
•Servers and computer networks
•Network administration
•Storage system installation and configuration
•Storage area network (SAN) management and direct attach storage (DAS)
•Fibre Channel (FC) and Ethernet protocols
iv Replacing a Controller
NetApp to Quantum Naming Decoder
Use Ta b l e 1 to correlate the NetApp product nomenclature to the equivalent Quantum-storage
naming conventions.
Ta b l e 1 Product Nomenclature
E-Series NetApp Product Quantum-Storage Description
Controller-Drive Tray Base System Quantum uses Base System when referring to a
drive tray with the RAID controllers.
Drive Tray Expansion Unit Quantum uses Expansion Unit when referring
to a drive tray with the environmental services
modules (ESMs).
E5600 (Code Name: Titan) RAID controller Four 16Gb/s FC SFP+ host ports
E5500 (Code Name: Soyuz) RAID controller Four 16Gb/s FC SFP+ host ports
E5400 (Code Name: Pikes Peak) RAID controller Four 8Gb/s FC SFP+ host ports
DE6600 (Code Name: Wembley) 4U 60-drive enclosure 60 3.5 inch disk drives
E5560 or E5660
(DE6600 4U drive enclosure with
E5500 or E5600 RAID controllers)
Quantum StorNext
QD7000
E5460
(DE6600 4U drive enclosure with
E5400 RAID controllers)
Quantum StorNext
QD6000
E5424
(DE5600 24-drive 2U drive
enclosure (Code Name: Camden)
with E5400 RAID controllers)
Quantum StorNext
QS2400
E5412
(DE1600 12-drive 2U drive
enclosure (Code Name: Ebbets)
with E5400 RAID controllers)
Quantum StorNext
QS1200
Copyright 2014 NetApp Inc. All rights reserved.
Replacing a Failed Controller Canister in the E5660 Controller-
Drive Tray
To access this product, go to the NetApp® support site at mysupport.netapp.com.
You can determine whether you have a failed controller canister in two ways:
The Recovery Guru directs you to replace a failed controller canister.
The amber Controller Service Action Required LED indicates a failed controller canister.
Before you replace the controller canister, gather antistatic protection, a new controller canister, and a controller air
blocker.
When you install a new controller, you must remove the battery from the failed controller, and install it in the new
controller. This procedure includes that task.
ATTENTION Possible loss of data access – Your new controller must have the same host interface card (HIC)
as the controller you are replacing. If the HICs do not match, do not attempt this procedure. The presence of mis-
matched controllers causes your storage array to lock down when you bring the new controller on line. You lose
access to your data until the problem is corrected.
ATTENTION Possible loss of data access – If the controller that you are replacing manages any secure volumes,
the new controller needs the correct security key to manage those volumes. After you replace the controller and
restore power to the controller-drive tray, you can use SANtricity® Storage Manager to load the key from the file in
which it was saved. Be sure that such a file exists and that you know the pass phrase required to install the security
key before you replace the controller.
ATTENTION Possible hardware damage – Because you perform this procedure with the power turned on, the
equipment might overheat if the controller slot is left open for more than three minutes. To prevent the possibility of
overheating, you must insert the controller air blocker into the controller slot when you service the controller.
2 - Replacing a Failed Controller Canister in the E5660 Controller-Drive Tray
Figure 1. E5660 Controller-Drive Tray
1. Power Canister A
2. Controller Canister A
3. Controller Canister B
4. Power Canister B
Removing a Controller Canister from the E5660 Controller-Drive
Tray
ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper
antistatic protection when handling tray components.
ATTENTION Possible extended outage – You must replace the controller with the power turned on to ensure
auto-code synchronization of the native controller firmware to the new controller and to prevent the possibility of an
extended outage.
1. Gather support data about your storage array by using one of these methods:
Use the storage management software to collect and save a support bundle of your storage array. From the
Array Management Window toolbar, select Monitor > Health > Collect Support Data Manually. Then
name and specify a location on your system where you want to store the support bundle.
Use the command line interface (CLI) to run the save storageArray supportData command to gather
comprehensive support data about the storage array.
For more information about this command, refer to the current version of the Command Line Interface and Script
Commands Programming Guide.
Replacing a Failed Controller Canister in the E5660 Controller-Drive Tray - 3
NOTE Gathering support data can temporarily impact performance on your storage array.
2. Did the Recovery Guru direct you to replace a failed controller canister?
Yes – Go to step 3.
No – Run the Recovery Guru to identify the failed controller canister, and then go to step 3.
3. Locate the failed controller canister by checking the Controller Service Action Required LEDs shown in the
following figure.
If a fault is detected, the amber Controller Service Action Required LED is on. You can safely remove the
controller canister when the blue Controller Service Action Allowed LED is on.
NOTE Your controller canister might have a different number and type of host interface connectors than what is
shown in the following figure.
Figure 2. E5600 Controller Service Action LEDs
1. Controller Service Action Allowed LEDs (Blue)
2. Controller Service Action Required LEDs (Amber)
3. Seven-Segment Display
4. Record the information from the seven-segment display on the rear of the controller-drive tray.
The display flashes a sequence of codes. To find information about the displayed diagnostic codes, refer to the
E5600 Controller-Drive Tray and Related Drive Trays Installation Guide.
5. Is the Controller Service Action Allowed LED to on?
Yes – Go to step 8.
No – Go to step 6.
6. Use either the GUI (first bullet) or the CLI (second bullet) to take the appropriate controller offline.
From the Hardware pane in the Array Management Window, right-click the picture of the controller that you
want to take offline, and then select Advanced > Place > Offline.
Run the following command:
smCLI <DNS-network-name-or-IP-address> -c
“set controller [(a | b)] availability=offline”;
7. Wait for the Controller Service Action Allowed LED to come on.
This indication might take several minutes for a large configuration.
8. Put on antistatic protection.
4 - Replacing a Failed Controller Canister in the E5660 Controller-Drive Tray
ATTENTION Potential degraded performance – To prevent degraded performance, do not twist, fold, pinch,
or step on the cables. Many cables have a minimum bending radius. Check the specifications for your cables,
and do not bend any cable more tightly than the minimum specified radius.
9. Label each of the interface cables and Ethernet cables attached to the controller canister so that you can
reconnect each cable correctly after you reinstall the controller canister.
10.Disconnect all of the interface cables and Ethernet cables from the failed controller canister without disturbing the
other canister.
11.If the failed controller canister contains a Fibre Channel HIC or an InfiniBand HIC, remove the small form-factor
pluggable (SFP) transceivers (for Fibre Channel) or quad SFP (QSFP) transceivers (for InfiniBand) from the HIC
and save them for possible reuse.
12.Prepare the controller air blocker by removing it from its packaging and folding it inward at right angles so it is
ready to insert into the open controller slot.
Figure 3. Controller Air Blocker
13.Remove the failed controller canister.
NOTE The following figures show the controller in the bottom position within the controller-drive tray. However,
you might be removing the controller and inserting the controller air blocker in the top position. The required
actions are similar.
a. Unlock and pull out the release levers to release the controller canister.
Replacing a Failed Controller Canister in the E5660 Controller-Drive Tray - 5
b. Using the release levers and your hands, pull the controller canister out of the controller-drive tray.
Figure 4. Removing and Replacing a Controller Canister
1. Release Levers
2. Controller Canister
c. Set the failed controller canister on a flat, static-free surface with the release levers up.
ATTENTION Possible hardware damage – Because you perform this procedure with the power turned on, the
equipment might overheat if the controller slot is left open for more than three minutes. To prevent the possibility
of overheating, you must insert the controller air blocker into the controller slot when servicing the controller.
6 - Replacing a Failed Controller Canister in the E5660 Controller-Drive Tray
14.Insert the controller air blocker into the open controller slot to make sure that proper airflow is maintained.
Figure 5. Inserting the Controller Air Blocker into the Open Controller Slot
15.Remove the battery from the failed controller canister by performing these steps:
a. Press down on both of the top cover latch buttons as you slide the top cover off the controller canister.
Andere Handbücher für StorNext QD6000
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Quantum Lagerung Handbücher
Quantum
Quantum QX Series Bedienungsanleitung
Quantum
Quantum A-Series FTP Bedienungsanleitung
Quantum
Quantum QXS 12G Series Technisches Handbuch
Quantum
Quantum Quantum Atlas 10K II 9.2/18.4/36.7/73.4 GB Bedienungsanleitung
Quantum
Quantum Scalar i40 Bedienungs- und Sicherheitshinweise
Quantum
Quantum StorNext QD7000 Bedienungsanleitung
Quantum
Quantum DLTtape SDLT 220 Produktinformationsblatt
Quantum
Quantum Superloader 3 Bedienungsanleitung
Quantum
Quantum StorNext QM1200 Bedienungsanleitung
Quantum
Quantum LTO3 A-Series Bedienungsanleitung
Quantum
Quantum ValueLoader DLT VS160 Betriebsanleitung
Quantum
Quantum DXi V1000 Montageanleitung
Quantum
Quantum PX500 Series Kurzanleitung
Quantum
Quantum Scalar 218FC Bedienungsanleitung
Quantum
Quantum Scalar 50 Bedienungsanleitung
Quantum
Quantum 6-67057-02 Rev A Bedienungsanleitung
Quantum
Quantum Sun StorEdge L25 Bedienungsanleitung
Quantum
Quantum Scalar 1000 Handbuch
Quantum
Quantum Scalar i40 Bedienungsanleitung
Quantum
Quantum DXi4510 Bedienerhandbuch
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung