Quantum DXi4510 Bedienerhandbuch

www.quantum.com

DXi4500

Contents

DXi4500 Configurations......................... 2

Choosing a Location .............................. 2

Installation Requirements.................. 2

Rack Space Requirements .................. 2

Environmental Conditions ................. 3

Preparing for the Installation ................ 3

Necessary Tools .................................. 3

Taking ESD Precautions...................... 3

Unpacking the DXi4500 ......................... 4

Installing the DXi4500 System............... 6

Locating the Mounting Position ........ 6

Installing the DXi4500 ....................... 7

Cabling the DXi4500 ........................ 10

Initial Configuration............................. 11

Accessing the DXi4500, Remote

Management Console...................... 11

Completing the Getting Started

Wizard .............................................. 14

Connecting the Ethernet Cables ...... 19

Creating a Typical Backup

Configuration................................... 20

DXi4500 Installation and

Configuration Guide

This guide provides basic installation and configuration instructions for the

DXi4500 system (see Figure 1). Make sure to read the DXi4500 Site

Planning Guide before starting your installation. The Site Planning Guide is

included on the documentation CD provided with your DXi4500 system.

Note: Make sure to take the online training for the DXi4500 in order to

make the best use of your product. The online training is available

at www.quantum.com/ServiceandSupport/StorageCareLearning/

Index.aspx

Figure 1 DXi4500 System

Note: This Installation and Configuration Guide is intended for DXi4500

with DXi 2.0.1 Software.

2DXi4500 Configurations

DXi4500 Installation and Configuration Guide

DXi4500 Configurations

The DXi4500 is available in the following configurations (see Ta b l e 1 ):

Table 1 DXi4500

Configurations

Choosing a Location

Quantum recommends installing the DXi4500 system in a controlled or restricted area

to prevent access by untrained personnel. In addition, Quantum recommends that

system installation be performed only by qualified IT personnel.

When choosing an installation site for the DXi4500 system, consider the following

requirements:

•Installation Requirements on page 2

•Rack Space Requirements on page 2

•Environmental Conditions on page 3

Installation

Requirements

Review the DXi4500 Site Planning Guide (6-67093) to ensure that your site meets the

installation requirements for the DXi4500.

Rack Space

Requirements

Tabl e 2 contains the rack requirements for the DXi4500 components.

Table 2 Rack Requirements

Configuration Number of Hard Drives Hard Drive Capacity

DXi4510 (2.2 TB Usable Capacity) 8500 GB

DXi4520 (4.4 TB Usable Capacity) 81 TB

DXi4500

Height 2U, 3.40 in (8 6 cm)

Width (side to side) 17.19 in (43.6 cm)

Depth (front to back) 24.09 in (61 cm)

Preparing for the Installation 3

DXi4500

Environmental

Conditions

The installation site must have the following environmental conditions:

• Humidity: 20% to 80% (non-condensing)

• Temperature: 10 to 35 °C (50 to 95 °F) 35 °C Max, Altitude = 900 m or 2952.75 ft

(28 °C Max, Altitude = 3048 m or 10,000 ft)

These environmental conditions apply when the DXi4500 system is in operation.

Note: For additional specifications, refer to the Quantum DXi4500 User’s Guide (6-

67092) located on the documentation CD.

Preparing for the Installation

Before you begin the installation procedure in this section, make the following

preparations as described in this section:

•Necessary Tools on page 3

•Taking ESD Precautions on page 3

Necessary Tools Provide the following tools for unpacking and installing the DXi4500:

• #2 PHILLIPS screwdriver

• Notebook PC (for setting up initial system configuration)

Taking ESD Precautions Some components within the DXi4500 system contain static-sensitive parts. To avoid

damaging these parts while performing installation procedures, always observe the

following precautions:

• Keep the DXi4500 system turned off during all installation procedures.

• Keep static-sensitive parts in their original shipping containers until ready for

installation.

• Do not place static-sensitive parts on a metal surface. Place them inside their

protective shipping bag or on an antistatic mat.

• Avoid touching connectors and other components.

Weight (stand alone) 49.5 lbs (22.5 Kg)

Air Clearance Open 4 in (10.2 cm) behind unit for proper air flow

DXi4500

4Unpacking the DXi4500

DXi4500 Installation and Configuration Guide

Note: Dry climates and cold-weather heating environments have lower relative

humidity and are more likely to produce static electricity.

Unpacking the DXi4500

By following these instructions, you help ensure that the system will continue to be

safeguarded after it arrives at the installation site.

Unpack and remove the following components from the packing materials (see

Figure 2):

• DXi4500 chassis

• Front bezel with key

• (4) power cords, (2) U.S. and (2) C13 to C14 cables

• Ethernet cables

• Left and right slide assemblies

• Cable-management arm

• Left and right cable-management arm ramp assemblies

• DXi4500 Quick Reference and Documentation CD

• DXi4500 Installation and Configuration Instructions

• Accessory kit

Caution: Do NOT discard the packing materials after the system is unpacked. The

packaging materials must be used if the system is relocated.

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

Unpacking the DXi4500 5

DXi4500

Figure 2 Unpacking the

DXi4500

Slide rails

Tie bands

Chassis rails Front bezel

6Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Installing the DXi4500 System

Installing the DXi4500 in a rack consists of the following steps:

1Locating the Mounting Position on page 6

2Installing the DXi4500 on page 7

3Cabling the DXi4500 on page 10

Locating the Mounting

Position

The DXi4500 systems is designed to fit in a standard 19 inch wide rack. It is important

for the chassis installation to locate the hole pattern in the rack rails. You must allow 2U

(3.5 in (8.9 cm)) of vertical space for the DXi4500 system. Rack cabinets that meet EIA-

310 standards have an alternating pattern of three holes per rack unit with center-to-

center hole spacing (beginning at the top hole of a 1-U space) of 15.9 mm, 15.9 mm,

and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the front and back vertical rails

(see Figure 3). Rack cabinets may have round or square holes.

Figure 3 Rail Hole Pattern

WARNING: If the rack is empty at the time of installation, do NOT install the DXi4500

chassis too high in the rack. The weight of the chassis may cause the rack

to become “top heavy” and unstable if installed in the top of an empty

rack.

To mark the rack, perform the following step:

1Place a mark (or tape) on the rack's front vertical rails where you want to locate the

bottom of the system you are installing in the rack. The bottom of each 1-U space is

at the middle of the narrowest metal area between holes (marked with a horizontal

line on some rack cabinets).

1 U (44 mm [1.75 inches])

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

1 U (44 mm [1.75 inches])

Installing the DXi4500 System 7

DXi4500

Installing the DXi4500 Installing the DXi4500 consists of the following steps:

1Installing the DXi4500 Rack Mounting Rails on page 7

2Installing the DXi4500 Chassis on page 9

Installing the DXi4500 Rack Mounting Rails

1Install the rack mounting rails (see Figure 4 for square holes and Figure 5 for Round

holes):

aPosition the left and right rail end pieces of the rail module labeled FRONT

facing inward and orient each end piece to seat in the square holes on the front

side of the vertical rack flanges. Align each end piece to seat the pegs in the

bottom hole of the first U space and the top hole of the second U space.

bEngage the back end of the rail until it fully seats on the vertical rack flange and

the second tooth on the latch locks in place.

Note: To remove the rack mounting rails, pull the Release latch located on the

front of the rail.

Figure 4 Installing the Rack

Mounting Rails (Square Holes)

Front side of rack rails

Front of rack

Back of rack

Rail teeth

Rail pegs

Second tooth

engaged

Release

button

Release

button

8Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Figure 5 Installing the Rack

Mounting Rails (Round Holes)

2Place the DXi4500 on a level surface and align the four keyhole slots on the chassis

rails with the corresponding pins on the system. Slide the chassis rails towards the

back of the system until each one locks into place (see Figure 6).

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

Note: To disengage the chassis rails, pull the latch and push the rails toward the front

of the chassis.

Front side of rack rails

Front of rack

Back of rack

Rail teeth

Rail pegs

Second tooth

engaged

Release

button

Release

button

Installing the DXi4500 System 9

DXi4500

Figure 6 Installing the Chassis

Rails

Installing the DXi4500 Chassis

WARNING: Ensure that the system is properly supported until the chassis rails are

locked into the slide rails on both sides.

1To install the DXi4500 chassis (see Figure 7):

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

aPull the slide rails out of the rack until they lock into place.

bAlign and insert the ends of the chassis rails into the ends of the slide rails. Push

the system inward until the chassis rails lock into place.

cPush or pull the blue tab located near the front of the system and slide the

system into the rack.

Front

Back

Chassis rails

Latch

10 Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Figure 7 Installing the

DXi4500 Chassis

Cabling the DXi4500 To cable the DXi4500 (see Figure 8):

1Connect a power cable to each power supply (two).

Note: It is recommended that you connect each power cord to a separate AC

circuit to ensure system availability in case of a power failure.

2Do NOT connect any Ethernet cables at this time.

Slide rails extended

DXi4500 chassis

Blue tab

Chassis rails

Andere Handbücher für DXi4510

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Quantum Lagerung Handbücher

Quantum

Quantum LTO-4 (Model B) Bedienungsanleitung

Quantum

Quantum DXi4700 Installations- und Betriebshandbuch

Quantum

Quantum Atlas V Bedienungsanleitung

Quantum

Quantum E240 Bedienungsanleitung

Quantum

Quantum DXi6900-S Bedienungsanleitung

Quantum

Quantum 6-67057-02 Rev A Bedienungsanleitung

Quantum

Quantum DLTtape DLT1 Bedienungsanleitung

Quantum

Quantum SNC 5100 Bedienungsanleitung

Quantum

Quantum ValueLoader DLT VS160 Betriebsanleitung

Quantum

Quantum DLTtape DLT 2000 Handbuch

Quantum

Quantum Scalar 10K Bedienungsanleitung

Quantum

Quantum Q2080 Technische Daten

Quantum

Quantum SuperLoader 3A Series Bedienungsanleitung

Quantum

Quantum DXi6900-S Kurzanleitung

Quantum

Quantum QXS-424 Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum DLTtape SDLT 600 Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Bedienungsanleitung

Quantum

Quantum Scalar 1000 Bedienungsanleitung

Quantum

Quantum DLT 2500 Bedienungsanleitung

Quantum

Quantum P1000 Series Bedienungsanleitung

Quantum

Quantum DXi4520 Bedienerhandbuch

Quantum

Quantum ValueLoader LTO-2 Bedienungsanleitung

Quantum

Quantum StorNext QM1200 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung