Quantum StorNext QM1200 Bedienungsanleitung

StorNext QM1200/QS1200/QS2400 Expansion Unit

Replacing a Power-Fan Canister

6-67554-02 Rev B *6-67554-02 B*

ii Replacing a Power-Fan Canister

StorNext QM1200/QS1200/QS2400 Expansion Unit, Replacing a Power-Fan Canister, 6-67554-02 Rev B, April 2015,

Product of USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including

but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation

may revise this publication from time to time without notice.

Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written

authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Quantum, the Quantum Logo, Backup. Recovery. Archive. It's What We Do., Be Certain, Be Quantum Certain, DLT, the DLT

Logo, DLTSage, DLTtape, the DLTtape Logo, DXi, DXi Accent, Dynamic Powerdown, FastSense, FlexLink, GoProtect,

GoVault, iLayer, Lattus, MediaShield, Optyon, Pocket-sized., Well-armored., Preserving the World's Most Important Data.

Yours., Q-Cloud, Quantum Certain, Quantum Certainty, Quantum vmPRO, Scalar, SDLT, SiteCare, SmartVerify,

StorageCare, StorNext, Super DLTtape, SuperLoader, and Vision are either registered trademarks or trademarks of

Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property

of their respective owners.

Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their

respective companies. All other brand names or trademarks are the property of their respective owners.

Quantum specifications are subject to change.

StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 1 -

Replacing a Power-Fan Canister in the StorNext

QM1200/QS1200/QS2400 Expansion Unit

Use these procedures to replace a failed power-fan canister in the StorNext QM1200/QS1200/QS2400 Expansion Unit.

Before you start to replace the power-fan canister in the StorNext QM1200/QS1200/QS2400 Expansion Unit, gather

antistatic protection and the appropriate replacement power-fan canister (AC power or DC power)

Locating the Failed Power-Fan Canister

1. Refer to Figure 1 to locate the power-fan canisters within the expansion unit.

Figure 1 Power-Fan Canister Locations

1. ESM A

2. ESM B

3. Power-fan canister A

4. Power-fan canister B

2. Check the Power-Fan Service Action Required LED to locate the failed power-fan canister (Figure 2).

If a fault is detected, the amber Power-Fan Service Action Required LED is on. If you can safely remove the

power-fan canister, the blue Power-Fan Service Action Allowed LED is on.

Possible equipment damage – If you perform this procedure with the power turned on, you must

complete it within three minutes to prevent the possibility of overheating the equipment.

StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 2 -

Figure 2 LEDs on a Power-Fan Canister

1. Standby Power LED (Green)

2. Power-Fan Output DC Power LED (Green)

3. Power-Fan Service Action Allowed LED (Blue)

4. Power-Fan Service Action Required LED (Amber)

5. Power-Fan Input AC Power LED (Green)

Gathering Support Data/Unpacking Power-Fan Canister

Before you start to replace the power-fan canister in the expansion unit, gather antistatic protection and a

replacement AC power-fan canister.

You can determine whether you have a failed power-fan canister in two ways:

The Recovery Guru directs you to replace a failed power-fan canister.

You locate the failed power-fan canister by checking the amber Power-Fan Service Action Required LED.

1. Gather support data through one of the following methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a

location on your system where you want to store the support bundle.

—Use the command line interface (CLI) to run the save storageArray supportData command to

gather comprehensive support data about the storage array. For more information about this command,

refer to Command Line Interface and Script Commands. Running this command can temporarily impact

performance on your storage array.

2. Did the Recovery Guru direct you to replace a failed power-fan canister?

—Yes – Go to step 4.

—No – Run the Recovery Guru to identify the failed component, and go to step 3.

3. If the Recovery Guru has directed you to replace the power-fan canister and the blue Power-Fan Service Action

Allowed LED is not on, use either the command line or the GUI to prepare the power-fan canister for removal

a. On the command line, type this command and press Enter:

SMcli <ctrl_IP1> -c “Set tray [trayID] powerfanCanister [left|right] service

Allowed Indicator=on;”

In this command:

—<ctlr_IP1>is the identifier of the controller to which the expansion unit is assigned.

ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper

antistatic protection when handling tray components.

StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 3 -

—[trayID]is the identifier of the expansion unit that contains the power-fan canister that you want to

replace. Drive tray ID values are 0 to 99. Be sure to type the square brackets around the identifier.

—[left|right] is the identifier of the power-fan canister you want to replace. Valid values are left or

right. Be sure to type the square brackets around the value.

b. On the GUI, click on the image of the tray that contains the power-fan canister you want to replace. From the

Array Management Window toolbar, select Hardware >> Prepare for Removal.

4. Put on antistatic protection.

5. Unpack the new power-fan canister.

a. Set the new power-fan canister on a flat, static-free surface near the expansion unit.

b. Save all packing materials in case you need to return the power-fan canister.

Removing the Power-Fan Canister

1. Turn off the Power switch on the power-fan canister that has failed (Figure 3).

Figure 3 AC Power Switch on the Drive Tray

1. AC Power Switch

2. Remove the plastic strain relief from the power cord.

3. Unplug the power cord from the failed A power-fan canister.

4. Remove the power-fan canister from the expansion unit (Figure 4 on page 4).

a. Rotate the latches outward to disengage the power-fan canister.

b. Use the latches as handles to pull the power-fan canister out of the expansion unit.

NOTE While removing the power-fan canister, you might notice an increase in fan speed. The fan speed returns to normal after you

have replaced the power-fan canister.

StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 4 -

Figure 4 Removing a Power-Fan Canister

Installing the Power-Fan Canister

1. Slide the replacement power-fan canister all the way into the expansion unit. Rotate the latches towards the

center to lock the power-fan canister into place.

2. Make sure that the Power switch on the replacement power-fan canister is turned off, and plug in the power cord.

3. Attach the plastic strain relief to the power cord, and make sure that it fits snugly up against the power-fan

canister.

4. Turn on the Power switch on the replacement power-fan canister.

5. Check the Power-Fan Input AC Power LED, and the Power-Fan Service Action Required LED on the new power-fan

canister (Figure 2 on page 2).

6. Based on the LED status, perform one of these actions:

—The Power-Fan Input AC Power LED are on and the Power-Fan Service Action Required LED is off – Go to

step 8.

—The Power-Fan Output DC Power LED and the Power-Fan Input AC Power LED are off or the Power-Fan

Service Action Required LED is on – Check that the power-fan canister is installed correctly. Reinstall the

power-fan canister. Go to step 7.

7. Did this action correct the problem?

—Yes – Go to step 8.

—No – If the problem has not been resolved, contact your Customer and Technical Support representative.

8. Using the LEDs and the storage management software, check the status of all of the trays in the storage array.

9. Does any component have a Needs Attention status?

StorNext QM1200/QS1200/QS2400 Expansion Unit - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 5 -

—Yes – Click the Recovery Guru toolbar button in the Array Management Window, and complete the recovery

procedure. If the problem has not been resolved, contact your Customer and Technical Support

representative.

—No – Go to step 10.

10. Remove the antistatic protection.

11. Gather support data on your updated storage array through one of the following methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a

location on your system where you want to store the support bundle.

—Use the CLI to run the save storageArray supportData command to gather comprehensive support

data about the storage array. For more information about this command, refer to Command Line Interface and

Script Commands. Running this command can temporarily impact performance on your storage array.

Andere Handbücher für StorNext QM1200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Quantum Lagerung Handbücher

Quantum

Quantum DLTtape DLT 4000 Bedienungsanleitung

Quantum

Quantum DLT-S4 Bedienungsanleitung

Quantum

Quantum SuperLoader 3A Series Betriebsanleitung

Quantum

Quantum DXi6900-S Kurzanleitung

Quantum

Quantum P1000 Series Bedienungsanleitung

Quantum

Quantum PowerStor L200 Bedienungsanleitung

Quantum

Quantum QXS-424 Bedienungsanleitung

Quantum

Quantum DLTtape DLT1 Bedienungsanleitung

Quantum

Quantum Scalar i40 Bedienungsanleitung

Quantum

Quantum Tape Drive A-Series Bedienungsanleitung

Quantum

Quantum ATL M1500 Bedienungsanleitung

Quantum

Quantum LTO 3A Bedienungsanleitung

Quantum

Quantum ValueLoader LTO-2 Bedienungsanleitung

Quantum

Quantum DLTtape DLT 4000 Bedienungsanleitung

Quantum

Quantum DLT 2500 Bedienungsanleitung

Quantum

Quantum LTO3 A-Series Bedienungsanleitung

Quantum

Quantum DLTtape DLT 4000 Bedienungsanleitung

Quantum

Quantum DLTtape SDLT 220 Handbuch

Quantum

Quantum Scalar i2000 Bedienungsanleitung

Quantum

Quantum StorNext QD7000 Montageanleitung

Quantum

Quantum DXi6900 Bedienungsanleitung

Quantum

Quantum Scalar i2000 Bedienungsanleitung

Quantum

Quantum ValueLoader DLT VS160 Bedienungsanleitung

Quantum

Quantum QXS G2 Series Betriebsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung