Quantum SuperLoader DLT Bedienungsanleitung
This Quick Start Guide gives the
steps for replacing the drive carrier
assembly (DCA) of a Quantum
SuperLoader.
These instructions are for both
the SuperLoader DLTTM (which
includes the SuperLoader SDLT)
and SuperLoader LTO due to the
nature of their similarities. In
general, the SuperLoader DLT is
used in the illustrations. Though the
components are similar in appearance,
many component parts are not
interchangeable. These include the
magazines, cartridges, drive carrier
assembly, magazine blank, magazine
handle, and the bar code reader.
For additional information, visit
www.quantum.com, refer to the
Quantum Superloader Automated
Tape Library User Manual
installed as
a PDF (portable document format) file
on the SuperLoader Documentation
CD, or contact Quantum Technical
Support and Customer Service by
calling 1-800-284-5101.
Note: Adobe Acrobat Reader
4.0 or later is required to view
and print PDF documents.
To download a free copy of
Adobe Acrobat Reader, go to
www.adobe.com.
Step 1: Unpack the DCA
a. Look for markings on the shipping carton that indicate the top. If necessary,
position the carton so that it is right-side up.
b. Using scissors, a utility knife, or other appropriate tool, carefully cut the packing
tape along the length and ends of the carton.
c. Fold open the box flaps.
d. Remove the plastic bag containing installation hardware (four screws).
e. Reach into the carton with both hands, lift the DCA and its foam pads out of the
box, and place the DCA on a flat work surface.
f. Rotate the DCA so that one foam pad is against the work surface and the other is
above the DCA.
g. Remove the exposed foam pad from the DCA.
h. Rotate the DCA so that the other foam pad is up. Remove the foam pad.
The DCA should still be inside antistatic packaging.
Caution: This device is static-sensitive. Proper grounding and electrostatic
discharge (ESD) handling precautions are required before removing the
DCA from its packaging. These precautions include unpacking the DCA in
a static-free work area and using an antistatic wrist band as well as other
antistatic apparel.
i. Set the DCA down on the work surface.
Step 2: Prepare for Removal and Replacement
Caution: Do not apply power to the DCA unless the DCA is fully installed in
the SuperLoader and secured by all four mounting screws.
a. Make sure you have the following tools:
• #2 PHILLIPS® screwdriver
b. Take appropriate ESD precautions. Leave the replacement DCA in its antistatic
packaging until you are ready to install it.
SuperLoaderTM Drive Carrier Assembly (DCA) Replacement
Quick Start Guide
For more information,
visit our Web site at
www.quantum.com
United States of America
Quantum Corporation
Storage Solutions Group
141 Innovation Drive
Irvine, CA 92612
U.S.A.
phone 949.856.7800
fax 949.856.7799
© 2004 Quantum Corporation. All rights reserved. DLTtape, the DLTtape logo, Quantum, the Quantum logo, SuperDLTtape, the Super DLTtape logo, and SuperLoader are trademarks of
Quantum Corporation registered in the U.S.A. and other countries. Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their
respective companies. All other brand names or trademarks are the property of their respective owners.
Europe
7 Lindenwood
Chineham Business Park
Basingstoke, RG24 8QY
United Kingdom
phone +44 1256 818300
fax +44 1256 848700
Asia Pacific
Level 3
200 Creek Street
Brisbane, Qld 4000
Australia
phone +61 7 3839 0950
fax +61 7 3839 0955
Page 2
SuperLoader Drive Carrier Assembly (DCA) Replacement Quick Start Guide
Step 3: Remove the Current DCA
Note: Before you remove the DCA, make sure the
tape drive does not contain a tape cartridge. For
instructions about unloading a cartridge from the tape
drive, refer to the User’s Guide.
a. Turn off the SuperLoader using the front panel button.
b. Disconnect all cables from the back of the DCA.
c. Remove the four screws that secure the DCA to the chassis at
the rear of the SuperLoader.
Caution: While removing or handling the SuperLoader
DLT DCA, do not touch the exposed printed circuit
board assembly on the underside of the unit.
d. With one hand, grasp the DCA handle and slide the DCA out
while supporting it from underneath with your other hand.
e. Set the DCA
Screws
DCA bay
DCA
Handle
e. Set aside the DCA you just removed.
Note: The DCA must be returned to Quantum in the
replacement DCA packaging within 7 business days.
For further information, refer to the return material
authorization (RMA) instructions shipped with the
replacement DCA.
Step 4: Install the Replacement DCA
Caution: While removing or handling the SuperLoader
DLT DCA, take appropriate ESD precautions to prevent
accidentally touching or damaging the exposed
printed circuit board assembly on the underside of
the unit.
a. Remove the replacement DCA from its antistatic packaging.
b. Grasp the DCA by the handle with one hand and support the
underside of the DCA with the other hand.
c. Slide the DCA into the DCA bay. Make sure you position the
DCA correctly; it should slide smoothly into the bay.
d. Install the four screws (included with the replacement DCA)
to secure the DCA to the SuperLoader chassis. Tighten the
screws firmly.
e. Make sure that the AC power switch on the back of the DCA
is off. Then, connect the power and SCSI cables.
f. Turn on the SuperLoader by pressing the AC power switch at
the back of the unit. Verify that the SuperLoader is operating
properly.
Note: On all SuperLoaders, SCSI terminators must be
used for proper operation of the drive.
81-81264-01 A01 Rev. August 2004 6207947-07cN 01
Andere Handbücher für SuperLoader DLT
1
Dieses Handbuch passt für folgende Modelle
1
Andere Quantum Lagerung Handbücher
Quantum
Quantum DLTtape DLT 2000 Handbuch
Quantum
Quantum LTO-9 HH SAS Bedienungsanleitung
Quantum
Quantum Superloader 3 Bedienungsanleitung
Quantum
Quantum StorNext QM1200 Bedienungsanleitung
Quantum
Quantum StorNext QD7000 Bedienungsanleitung
Quantum
Quantum Scalar i40 Bedienungsanleitung
Quantum
Quantum Scalar i6 Bedienungsanleitung
Quantum
Quantum PX500 Series Kurzanleitung
Quantum
Quantum Superloader 3 Bedienungsanleitung
Quantum
Quantum 6-67057-02 Rev A Bedienungsanleitung
Quantum
Quantum DLT-V4 Bedienungsanleitung
Quantum
Quantum DLTtape SDLT 220 Bedienungsanleitung
Quantum
Quantum ValueLoader LTO-2 Bedienungsanleitung
Quantum
Quantum DLTtape DLT1 Bedienungsanleitung
Quantum
Quantum DXi4510 Bedienerhandbuch
Quantum
Quantum F2000 Bedienungsanleitung
Quantum
Quantum DLTtape DLT 4000 Bedienungsanleitung
Quantum
Quantum Scalar 24 Betriebsanleitung
Quantum
Quantum STD2401LW Bedienungsanleitung
Quantum
Quantum DLTtape DLT1 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung