R.V.R. Elettronica URP Bedienungsanleitung

Manufactured by R.V.R. Elettronica -Italy

URP

TECHNICALAND MAINTENANCE MANUAL

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 2

URP

Portable FM Exciter 87.5-

108 MHz Range

TechnicalandMaintenanceManual

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 3

INDEX

Preliminary Instructions and Warranty InformationsPag.5

Safety RegulationsPag. 7

CHAPTER 1

General DescriptionPag. 9

Electrical Specifications (Table A)Pag.10

Dimensional & Environmental Specifications (Table B)Pag.12

CHAPTER 2

Electrical DescriptionPag.13

Front Panel View DescriptionPag.15

Front Panel View (Fig. 1)Pag.16

Rear Panel View DescriptionPag.17

Rear Panel View (Fig. 2)Pag.18

CHAPTER 3

Installation ProcedurePag.19

Main Voltage Connections (Fig. 3)Pag.21

Audio Input Connections (Fig. 4)Pag.22

APPENDIXA

Circuit Diagrams, Layouts and Bill of MaterialsPag.23

Card Connections DiagramPag.24

Front Panel CardPag.25

Synthesis CardPag.29

R.F. Amplifier CardPag.34

VCO/AFCardPag.39

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 4

PRELIMINARY INSTRUCTIONS

AND WARRANTY INFORMATION

WARNING: This equipment is a"CLASS A" equipment. In aresidential place

this equipment can cause hash. In this case can be requested to user to

take the necessary measures.

Please observe safety precautions when handling this unit.

This equipment contains dangerous currents and high voltages.

This manual is written as ageneral guide for those having previous

knowledge and experience with this kind of equipment. It is not intended

to contain acomplete statement of all safety warnings which should be

observed by personnel in using this or other electronic equipment.

R.V.R. doesn’t assume responsability for injury or damage resulting from

improper procedures or practices by untrained/unqualified personnel in

the handling of this unit.

Please observe all local codes and fire protection standards in the

operations of this unit.

CAUTION: always disconnect power before opening covers or removing any

part of this unit. Use appropriate grounding procedures to

short out capacitors and high voltage points before servicing.

Any damage to the goods must be reported to the carrier in writing on

the shipment receipt. Any discrepancy or damage discovered subsequent

to delivery, shall be reported to R.V.R. within five (5) days from its

receipt.

R.V.R. extends to the original end-user purchaser all original

manufacturers warranties which are transferable and all claims are to

be made directly to R.V.R. per indicated procedures.

All manufacturers warranties will be supported by R.V.R. to ensure

precise and speedy service where possible.

R.V.R. shall not be liable for any damage of whatsoever nature, arising

out of or in connection with the product or its use thereof.

R.V.R.’s warranty shall not include:

1) Re-shipment of the unit to R.V.R. for repair purposes

2) Any unauthorized repair/modification

3) Incidental/consequential damages as a result of any defect

4) Nominal non-incidental defects

5) Re-shipment costs or insurance of the unit or replacement

units/parts

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 5

Warranty shall come into force from invoice date and for the period

of the manufactures warranty.

The warranty for aperiod of 12 months is referred to any R.V.R.

product, while for products as Transistors, Mos-Fet and Tubes of the

final stages is applied the manufacture's warranty off these devices.

To claim your rights under this warranty:

a. Contact the dealer or distributor where you purchased the unit.

Describe the problem and ask if he has an easy solution. Dealers

and Distributors are supplied with all the information about

problems that may occur and usually they can repair the unit quicker

than what the manufacturer could do. Very often installing errors

are discovered by dealers.

b. If your dealer cannot help you, contact R.V.R. in Bologna and explain

the problem. If it is decided to return the unit to the factory,

R.V.R. will mail you aregular authorization with all the necessary

instructions to send back the goods.

c. When you receive the authorization, you can return the unit. Pack

it carefully for the shipment, preferably using the original packing

and seal the package perfectly. The customer always assumes the

risks of loss (i.e., R.V.R. is never responsible for damage or loss),

until the package reaches R.V.R. premises. For this reason, we

suggest you to insure the goods for the whole value. Shipment must

be effected C.I.F. (PREPAID) to the address specified by R.V.R.’s

service manager on the authorization.

DO NOT RETURN UNITS WITHOUT OUR AUTHORIZATION AS THEY WILL BE

REFUSED.

Be sure to enclose awritten technical report where mention all the

problems found and acopy of your original invoice establishing the

starting date of the warranty.

Replacement and warranty parts may be order from the following address.

Be sure to include the equipment model and serial number as well as part

description and part number.

R.V.R. Elettronica S.r.l.- Broadcasting Equipment -

Via del Fonditore, 2/2c

40138 Bologna - Italy

Telephone +39-51-6010506

Fax +39-51-6011104

R.V.R. reserves the right to modify the design and specifications of the

equipment in this manual without previous notice.

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 6

WARNING!

The currents and voltages in this equipment are dangerous!

Personnel must at all times observe safety regulation!

This manual is intended as ageneral guide for trained and qualified

personnel who are aware of the dangers inherent in handling potentially

hazardous electrical and electronic circuits.

It is not intended to contain acomplete statement of all safety

precautions which should be observed by personnel in using this or other

electronic equipment.

The installation, operation, maintenance and service of this equipment

involves risks both to personnel and equipment, and must be performed

only by qualified personnel exercising due care.

R.V.R. ELETTRONICA S.r.l. shall not be responsible for injury or damage

resulting from improper procedures or from the use of improperly trained

or inexperienced personnel performing such tasks.

During installation and operation of this equipment, local building codes

and fire protection standards must be observed.

WARNING!

Always disconnect power before opening covers,

doors, enclosures, gates, panels or shields.

Always use grounding sticks and short out high

voltage points before servicing. Never make

internal adjustments, perform maintenance or

service when alone or when fatigued.

Do not remove, short-circuit or tamper with interlock switches on access

covers, doors, enclosures, gates, panels or shields.

Keep away from live circuits, know your equipment and don’t take chances.

WARNING!

In case of emergency ensure that power has been disconnected

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 7

TreatmentofelectricalShock

1) If victim is not responsive follow the A-B-C's of basic life support.

PLACE VICTIM FLAT ON HIS BACK ON A HARD SURFACE

AAIRWAYBBREATHING

IF UNCONSCIOUS,IF NOT BREATHING,

OPEN AIRWAYBEGIN ARTIFICIAL

BREATHING

LIFT UP NECK,TILT HEAD,

PUSH FOREHEAD BACK,PINCH NOSTRILS,

CLEAR OUT MOUTH IF NECESSARY,MAKE AIRTIGHT SEAL,

OBSERVE FOR BREATHING.4 QUICK FULL BREATHS.

REMEMBER MOUTH TO MOUTH

RESUSCITATION MUST BE

COMMENCED AS SOON AS

POSSIBLE.

CCIRCULATION

CHECK CAROTID PULSEDEPRESS STERNUM 11/2" TO 2"

IF PULSE ABSENT,APPROX. 80 SEC. : ONE RESCUER, 15 COMPRESSIONS,

BEGIN ARTIFICIAL2 QUICK BREATHS.

CIRCULATION APPROX. 60 SEC. :TWO RESCUERS, 5 COMPRESSIONS,

1BREATH

NOTE: DONOTINTERRUPT RHYTHMOF COMPRESSIONS

WHEN SECONDPERSON IS GIVING BREATH.

Call for medicalassistanceassoonaspossible.

2) If victim is responsive.

a. Keep them warm.

b. Keep them as quiet as possible.

c. Loosen their clothing (a reclining position is recommended).

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 8

FIRST-AID

Personnelengagedintheinstallation,operation,maintenanceor

servicingofthisequipmentareurgedtobecomefamiliarwithfirst-aid

theoryandpractices.Thefollowinginformationisnotintendedtobe

acompletefirst-aidprocedure,itisbriefandisonlytobeusedas

areference.Itisthedutyofallpersonnelusingtheequipmenttobe

preparedtogiveadequateEmergencyFirstAidandtherebyprevent

avoidablelossoflife.

TreatmentofelectricalBurns

1) Extensive burned and broken skin.

a. Cover area with clean sheet or cloth.

(Cleanest available cloth article).

b. Do not break blisters, remove tissue, remove adhered particles of

clothing, or apply any salve or ointment.

c. Treat victim for shock as required.

d. Arrange transportation to a hospital as quickly as possible

e. If arms or legs are affected keep them elevated.

NOTE

If medical help will not be available within an hour and the victim

is conscious and not vomiting, give him aweak solution of salt and

soda: 1 level teaspoonful of salt and 1/2 level teaspoonful of baking

soda to each quart of water (neither hot or cold).

Allow victim to sip slowly about 4ounces (half aglass) over aperiod

of 15 minutes.

Discontinue fluid if vomiting occurs (Do not give alcohol).

2) Less severe burns - (1st & 2nd degree)

a. Apply cool (not ice cold) compresses using the cleanest available

cloth article.

b. Do not break blisters, remove tissue, remove adhered

particles of clothing, or apply salve or ointment.

c. Apply clean dry dressing if necessary.

d. Treat victim for shock as required.

e. Arrange transportation to a hospital as quickly as possible.

f. If arms or legs are affected keep them elevated.

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 9

CHAPTER1

GENERAL DESCRIPTION

1.1 INTRODUCTION

The R.V.R. model URP are very compact externally powered FM exciters

which may be used as an economic alternative to alow power exciter or

as a portable unit.

1.2 ELECTRICAL DESCRIPTION

The URP is capable of either 10 watts or 2watts with the power output

being controlled by a switch on the front panel.

The URP/2 model is capable of 2 watts only.

Both units operate from an external power supply which must be regulated

to ensure stability of the operating frequency.

The supply voltage may be in the range of 12 VDC to 13.8 VDC.

Power output will very somewhat with the applied supply voltage.

1.3 SPECIFIACATIONS

Please refer to Table A for the elctrical specifications and

Table B for the mechanical specifications.

URP Technical and Maintenance Manual

R.V.R. Elettronica S.r.l. (Bo)Pag. 10

TABLEA

ELECTRICAL SPECIFICATIONS

DC Power Requirements12-13.8V, 2.2A

(approx) at 10Wor 1.7A

(approx) at 2.5W

Frequency Rangefrom87.5 to 108MHz

(other in request)

Frequency Rangedirect from frontpanelin

100KHzincrements-shift 50KHz

Frequency Stabilitybetterthan±500Hz

Max Power Output10W ±10% dependent on and

portionate tosupplied DC

Volatge (12-13.8V allowed)

R.F. OutputConnectorS0239 (PL)type

Output Impedance50 Ohm

AudioInputs2Total,5KOhmimpedance,

unbalanced,balanced.

1StandardstereomaleXLR

whichcan be used eitherfor

composite/wideband operation

or monaural operation

(switchable).

1Standard mono maleXLR

fordirect microphone usewith

built-in micropre-ampand

limiter.

InputLevelforStereoVersion2Vrms for 100%modulation

Input Level for Mono Version25mV rms for 100% modulation

Inhaltsverzeichnis

Andere R.V.R. Elettronica Industrieanlagen Handbücher

R.V.R. Elettronica

R.V.R. Elettronica TEX100 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica TEX150-LCD/S Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica RXRL-NV/2 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica VJ1000HP Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica HC4 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PTX30 UHT/S3 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica TOUCH30S Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica TEX300LCD Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica RDMODWEB Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica VJ2000 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica SDC20 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica SDC2000 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica URPT/MIC Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PJ10KPS-CA Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PJ5KPS Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica BLUES 30 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica HC5-10 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PJ250-NV Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PTRL-NV/2/S3 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica TEX20-NV Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PJ20KPS-C Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PTRL-NV/S3 Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica TCP/IP-INT-PTX Bedienungsanleitung

R.V.R. Elettronica

R.V.R. Elettronica PJRL250 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung