Rack Solutions 5U Bedienungsanleitung

Feature Identification

tekcarBgnitnuoMlenaPhctaP5rooDtnorF1

seloHsseccAelbaC6rooDlenaPpoT2

3 Horizontal Mounting Rails 7 Vents

4 Vertical Mounting Bracket

5U Vertical Wall Mount Rack Instruction Manual

Model:180-5281/180-5282

Cable Access and Management

The top and bottom panels of the wall mount rack both have circular holes for cable access. The top has three 1.75”

ports and two 1” ports, while the bottom has three 1” ports and two 1.75” ports.

Reversing the Front Door

The front door can be reversed by switching the configuration of its latch, lock and hinges. To reverse the door, simply

remove the screws that secure the latch, lock and hinges to the wall mount rack. Move each piece to the opposite side

of the wall mount rack, so that there are two hinges on one side (one at the top, one at the bottom) and the latch and

the lock on the other side.

Note: The unused screw holes are filled with rubber plug. To remove the rubber plug, push them through with a

screwdriver. Keep the rubber plug to refill unused screw holes.

Adjusting Mounting Rail Depth

The wall mount rack comes with reversible horizontal mounting rails that have threaded holes for mounting rack

equipment. The holes on the top of the rail are threaded for M6 hardware, while the holes on the bottom are threaded

for 12-24. To install equipment, use the included M6 or 12-24 hardware to secure equipment to the rails.

Adjustion Mounting Rail Depth

The two horizontal mounting rails are pre-installed to accommodate equipment with a mounting depth of 23 inches

(for item 180-5281) or 30 inches (for item 180-5282). Do not adjust the mounting rails unless your equipment requires

a different mounting depth. The rails can be adjusted in 1-inch increments for mounting depths between 20-23 inches

(508-584.2 mm) for 180-5281 and 27-30 inches (685.8-762 mm) for 180-5282.

1 Each rail is connected to the enclosure with 2 screws: 1 at the front of the enclosure and one at the rear. Using a

Philips-head screwdriver, remove the screws that fasten the rails to the enclosure.

2 Slide the mounting rails vertically to the desired depth and reattach them using the screws you removed in Step 1.

Equipment Installation

Mounting

Using a level, measure to position your mounting areas precisely. Use appropriate fasteners (not included) to secure

the enclosure to the wall.

Warning: The area you plan to mount the enclosure to must be able to withstand the weight of the enclosure and all

mounted equipment. For the weight of the enclosure and its capacity, see the specifications on page 5.

Install equipment until you have stabilized the enclosure. The threaded holes in the middle of each rack unit are

numbered. A single rack unit includes the space occupied by the numbered hole and the holes directly above and

below.

Note: If using sliding equipment rails, be careful when extending the rails. Do not extend more than one set of sliding

equipment rails at one time. Avoid extending sliding equipment rails near the top of the enclosure.

Locate the numbered openings in the mounting rails where you plan to install your equipment. Lower your equipment

into the enclosure and set it down on the mounting rails, lining up the mounting holes on the equipment with the

mounting rail’s mounting holes.

Specifications

kcaRtnuoMllaW,desolcnEepyTkcaR

Hole Type

Rack Height (U Space)

Rack Width

Rack Depth for item 180-5281 23”

Rack Depth for item 180-5282 30”

Hardware

Load Capacity*

Threaded Hole

19”

Included

150 lb (68.1 kg)

Note: Be sure to have the enclosure securely mounted to the wall, or in its final position on the floor before

mounting any equipment inside. Also be sure to have all the right adjustments on your rails before

mounting equipment.

Use the included mounting screws and washers to secure your equipment to the rack rail. Place the washers between

the screws and the equipment mounting brackets.

Optional Patch Panel Installation

The 180-5281 / 180-5282 both come with an integral, slide-out mounting bracket at the top of the enclosure. It can be

used to secure a patch panel to the enclosure, and it partially slides out for easier cabling access. To install a patch

panel on the patch panel mounting bracket, use the included mounting screws and washers to secure your equipment to

the rack rail. Place the washers between the screws and the patch panel mounting bracket.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rack Solutions Rack & Stand Handbücher

Rack Solutions

Rack Solutions 119-1752 Bedienungsanleitung

Rack Solutions

Rack Solutions 2UKVM-125 Bedienungsanleitung

Rack Solutions

Rack Solutions 1USHL-003 Bedienungsanleitung

Rack Solutions

Rack Solutions 122-2448 Bedienungsanleitung

Rack Solutions

Rack Solutions WALL-KYB-001 Bedienungsanleitung

Rack Solutions

Rack Solutions 104-2324 Bedienungsanleitung

Rack Solutions

Rack Solutions FORZA DESIGNS Elite Controller Wall Mount Bedienungsanleitung

Rack Solutions

Rack Solutions 122-3491 Bedienungsanleitung

Rack Solutions

Rack Solutions 111-1731 Bedienungsanleitung

Rack Solutions

Rack Solutions 104-2323 Bedienungsanleitung

Rack Solutions

Rack Solutions 1UKYB-126 Bedienungsanleitung

Rack Solutions

Rack Solutions 4UKIT-003BLK Bedienungsanleitung

Rack Solutions

Rack Solutions 101-5205 Bedienungsanleitung

Rack Solutions

Rack Solutions Wall-Mount-PC Bedienungsanleitung

Rack Solutions

Rack Solutions 122-4818 Bedienungsanleitung

Rack Solutions

Rack Solutions 105-2670 Bedienungsanleitung

Rack Solutions

Rack Solutions 104-2109 Bedienungsanleitung

Rack Solutions

Rack Solutions 104-2411 Bedienungsanleitung

Rack Solutions

Rack Solutions 124-2247 Bedienungsanleitung

Rack Solutions

Rack Solutions 104-1965 Bedienungsanleitung

Rack Solutions

Rack Solutions VEX 111-6330 Bedienungsanleitung

Rack Solutions

Rack Solutions 4Post Bedienungsanleitung

Rack Solutions

Rack Solutions RACK-117-MOBILE KIT Bedienungsanleitung

Rack Solutions

Rack Solutions 104-5191 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung