RADEMACHER 2696 Bedienungsanleitung
Item no.: 3100 00 14
VBD 549-2 (05.21)
ReWiSo 2696
Instruction manual for the electrical connection and for commissioning
EN
2
ENDear Customer,
i
...Congratulations on purchasing the ReWiSo, you have opted for
a quality product manufactured by RADEMACHER. Thank you for
the trust you have placed in us.
This manual...
...describes how to install, connect and operate the ReWiSo.
Before you begin, please read this manual through completely and follow
all the safety instructions.
This manual is part of the product. Please store it in an easily accessible place.
When passing the ReWiSo on to a third party, this manual must be passed on as well.
Damage resulting from non-compliance with this manual and the safety instructions
will void the warranty. We assume no liability for any consequential damage.
Key to symbols
i
Danger of fatal electric shock
i
This sign warns of danger when working on electrical connections, components, etc.
It requires that safety precautions be taken to protect the life and health of the person
concerned.
This concerns your safety.
Please pay attention and follow all instructions marked with this symbol.
This symbol warns of malpractices that can result in personal injury or property
damage.
NOTE/IMPORTANT/CAUTION
This is to draw your attention to information that is important for trouble-free operation.
3
ENContents
i
Dear Customer, ...........................................2
This manual.................................................2
Key to symbols...........................................2
Contents......................................................3
Description..................................................4
Included in delivery.......................................4
Instructions for commissioning .....................4
Connection and control possibilities .............4
Available automatic functions in overview....5
Operation.....................................................6
Button assignment and display symbols
on the weather data display..........................6
Display of brightness and wind velocity........7
Manual operation..........................................8
Setting the automatic functions ...............9
Calling up the automatic settings:.................9
A Brightness for the sun shading ............11
B Extension delay....................................12
C Retraction delay...................................12
D Indoor temperature lock.......................13
E Outdoor temperature lock ....................14
F Wind alarm...........................................15
Table: Wind velocity .............................16
G Rain alarm............................................16
H Saving the automatic settings..............17
Basic setting .............................................18
Calling up the basic settings:......................18
1. Radio connection to the weather
station ..................................................20
2. Rotation direction of the motor.............21
3. Running direction.................................22
4. Travel command in the event of a wind
or rain alarm............................................23
5. Transmission of the weather and
automatic data .....................................24
6. Sun shading position............................25
6.1. Retracted position ........................26
6.2. Setting the desired position..........26
6.3. Slat angle .....................................27
7. Saving the basic settings .....................27
Safety instructions for automatic
and alarm functions .................................28
Installation and commissioning..............29
Installation of the weather station
and connection of the drive.....................30
Location......................................................30
Fitting the bracket.......................................30
Preparation of the weather station..............31
Connection of the power supply and drive....32
Installation of the weather station...............33
Notes on installation of the weather station... 34
Installation of the operating unit.............34
Notes on radio systems...........................34
Commissioning.........................................35
Checking the sensors ..............................36
Checking the sun sensor............................36
Checking the wind sensor ..........................36
Checking the rain sensor............................37
Checking the temperature sensors.............37
Service / maintenance and care..............38
Weather station ..........................................38
Operating unit.............................................38
Inserting batteries (operating unit)..............38
Error messages ..........................................39
Calling up service data ...............................41
Factory settings........................................41
Abbreviations............................................42
Technical specications ..........................42
Radio technology........................................42
Operating unit.............................................42
Weather station ..........................................42
Weather station connection diagram .....43
View of the rear panel and weather station
drilling pattern..............................................44
View of the rear panel and operating unit
drilling pattern ............................................ 45
Control of several drives as a group ......46
Personal setting data for automatic
mode..........................................................46
Simplied EU declaration of conformity... 46
Warranty terms and conditions...............47
4
ENDescription
ReWiSo has been developed for automatic control and convenient manual operation
of an awning or Venetian blind. The controller has a very high degree of exibility for
connection and adjustment and can therefore be adapted individually to dierent instal-
lation conditions. Please use this operating manual to adapt the automatic functions
to suit your requirements.
Included in delivery
ReWiSo consists of a weather station and operating unit. Batteries (2x) to power the
operating unit are included.
Instructions for commissioning
Installation, testing, commissioning and troubleshooting on the controller may
only be carried out by a qualied electrician (according to VDE 0100).
Proceed as follows to commission the controller:
1. Carry out the mechanical installation and electrical connection (see the section
“Installation and commissioning”)
2. Carry out the basic setting (see the section “Basic setting”)
3. Adjust the automatic functions (see the section “Adjusting the automatic functions”)
Connection and control possibilities
An awning or Venetian blind drive can be connected to the controller. If several awnings
or Venetian blinds are to be controlled together, connection via a group control relay
is possible.
The following environmental parameters are measured and displayed:
uIndoor and outdoor temperature - energy-saving function
uBrightness
uWind velocity
uPrecipitation
i
5
EN
Available automatic functions in overview
uShading according to sun intensity with extension and retraction delay
uExtension to a programmed position in the case of adjustable Venetian blinds also
with setting of the slat angle
uBlocking of sun shading until a preselected indoor temperature is reached
(heat containment, only in automatic mode - energy-saving function)
uRetraction of sun shading below a preselected outdoor temperature
(frost protection, only in automatic mode)
uRetraction of sun shading above a preselected wind velocity
(wind alarm, function can be deactivated)
uRetraction of sun shading in the event of rain
(rain alarm, function can be deactivated)
The awning or Venetian blind is retracted in automatic mode below the preselected
brightness value or in the event of a rain or wind alarm. Wind and rain protection
functions are active also in manual mode if they have been set in automatic mode.
Description
i
6
ENOperation
Button assignment and display symbols on the weather data display
In the normal function, the operating unit of the controller displays the current outdoor
temperature (top line) and indoor temperature (bottom line), as well as the operating
mode (automatic or manual), the battery charge state and current alarm message for rain
or wind. The weather data is refreshed once a minute (and when a button is pressed).
Outdoor temperature
Indoor temperature
- Full (battery symbol displays the charge state of the battery)
- Half-full
- Empty
Automatic
mode
Manual
Battery
Manual/
Automatic
Up Stop Down Setting
Outdoor
temperature
Indoor
temperature
Rain alarm
Wind alarm
i
7
EN
Operation
Automatic mode active
Manual mode active. The connected drive was operated manually (with the
arrow buttons) or the button was pressed. The automatic functions are
thus deactivated and the awning or Venetian blind is not controlled according to
brightness or temperature. The safety functions ‘Rain alarm’ and ‘Wind alarm’
remain active. The controller remains in manual mode until it is switched to
automatic mode with the button.
Rain alarm. Outdoor awnings are retracted, manual operation is blocked.
The rain alarm function can be activated and deactivated in the automatic
settings (e.g. for indoor awnings or Venetian blinds).
Wind alarm. Outdoor awnings or Venetian blinds are retracted, manual operation
is blocked. The wind alarm function can be activated and deactivated in the
automatic settings (e.g. for indoor awnings).
Display of brightness and wind velocity
Press the SET button once briey while the temperature is displayed to display the
current brightness (in kilolux, kLux) and wind velocity (in metres per second, m/s).
The values are refreshed every 4 seconds.
Note: The wind velocity is not correctly displayed during the rst approx. 90 seconds
after the power is restored to the weather station (e.g. after a power failure or during
commissioning). Manual operation is therefore blocked during this period if the wind
alarm is active.
Pressing SET again briey recalls the temperature display (or the central command
display, see next section). The temperature is also displayed again automatically after
approx. 60 seconds.
i
8
EN
Operation
Manual operation
Manual control, pre-setting of the automatic functions and the basic setting of the
connected sun shading are performed with the buttons on the operating unit.
Up Stop Down
The connected awning or Venetian blind can be operated by hand using the buttons ,
and . The arrow buttons have an automatic timer function. Pressing the buttons
briey (less than 1 second) allows the awning or Venetian blind to be exactly positioned.
If the button is held depressed for longer than 1 second, the drive automatically runs
up to the end position. Pressing stops the drive.
If the rain or wind alarm is active, manual operation is blocked.
Manual/Automatic
The button switches back and forth between automatic mode (display )
and manual mode (display ). If the controller is operated manually using the ,
or buttons, it is then in manual mode. The automatic functions are then
deactivated and the awning or Venetian blind is not controlled according to brightness
or temperature. The button can be used to switch the controller back to automatic
mode (display ).
Pressing the SET button briey calls up the brightness and wind velocity display.
Holding the button depressed calls up the setting mode for the automatic functions and
the basic setting. For further details, see the section “Setting the automatic functions”
or “Basic setting”.
i
9
EN
In order that the awning or Venetian blind provides optimum sun shading, the values
for automatic mode have to be adapted to the conditions on site. The following settings
can be made in turn:
A. Brightness for the sun shading
B. Extension delay
C. Retraction delay
D. Indoor temperature lock
E. Outdoor temperature lock
F. Wind alarm
G. Rain alarm
H. Memory
Calling up the automatic settings:
Press the SET button in the weather data display for at least
3 seconds to call up the automatic settings.
You are in the automatic settings as soon as the two and symbols
appear on the left of the display. The rst parameter to be set (brightness)
is displayed.
Setting the automatic functions
i
10
ENSetting the automatic functions
You can exit the automatic settings at any time by pressing the button. The changes
made to the values are then not saved.
If no button is pressed in the automatic settings for 5 minutes, the display automatically
switches back to the temperature display. Changes to settings are again not saved.
You are in
the automatic
settings
Exit Conrm/
Next
+ -
i
Inhaltsverzeichnis
Andere RADEMACHER Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
