Radio Shack 19-1208 Bedienungsanleitung

OWNER’S MANUAL

19-1208

INTRODUCTION

Your Radio Shack 19-1208 Business band transceiver is a portable, easy-to-use, two-way

radio that you can carry almost anywhere. It is approved with commercial-grade standards

to give you clear, reliable communication. This transceiver consists of 8 Business channels.

Your 19-1208 provides for personal communications with family members or other licenses.

You can use the 19-1208 for recreational communications while you hike, ski, or fish. You

can even use the 19-1208 to coordinates your personal or business activities with other

family members. When you get a license to operate the radio, you can let other members

of your family living in the same household operate the radio.

Your transceiver has the following features:

PLL-Controlled Circuitry ---- provides accurate and stable channel selection.

Adjustable Squelch ---- helps eliminate noise between transmissions.

38 CTCSS (Continuous Tone Control Squelch System) ---- helps reduce interference

from other systems in the area operating on the same frequency.

Built-in Modulation Limiter Circuit ---- automatically adjusts for a wide variety of voice

levels to ensure an understandable transmission.

High/Low Power ---- lets you save power by selecting a suitable transmitting power for

long or short distances.

Battery Low and Transmit Indicator ---- shows the battery pack’s condition and lights

when you transmit or receive.

Removable and Rechargeable Battery Pack ---- lets you use one battery pack while you

charge another (additional packs available).

Supplied Battery Charger ---- conveniently recharges your transceiver’s battery pack.

Flexible Antenna with BNC Connector ---- provides excellent reception. The BNC

connector is designed so you can easily attach and remove the supplied antenna or an

optional one.

Earphone Jack and External Microphone Jack ---- let you use an earphone or external

microphone to help ensure understandable communications in noisy areas.

Belt Clip ---- lets you attach the transceiver to your belt or waistband.

JIS level 4 ---- provides excellent waterproof capability.

RADIOSHACK

CORP

FCC ID : AAO1901208

JOB # : 578ZA1

EXHIBIT # : 6

We recommend you record your transceiver’s serial number here. This number is on the

transceiver’s back panel.

Serial Number_______________________

FCC Information

FCC License required

This Transceiver is intended for use in the operation of commercial activities, in educational,

philanthropic, or ecclesiastical institutions, and hospitals, clinics, or medical associations.

The Federal Communications commission (FCC)requires you to be licensed before you

operate this transceiver. Unless you are already licensed to operate on one of the preset

frequencies, you must apply for a frequency through the PCIA (Personal Communication

Industry Association), a non-profit organization that assigns frequencies nationwide to help

prevent conflicts between different businesses using transceivers in the same area. For

more information about getting a license, contact the PCIA at 800-759-0300, extension 3068

(in Virginia 703-739-0300, extension 3068)

For other questions concerning the license application, contact the FCC at 717-337-1212, or

wirte:

FCC

P.O.Box 1040

Gettysburg, PA 17325

For the latest FCC application form and instructions, call the FCC’s fax-on-demand service

at 1-202-418-0177 from a fax machine and request one or more of the following documents:

All forms and instructions ……………………000600

Form 600 instructions only……………………006001

Main Form 600 only……………………………006002

Form 600 schedules only………………………006003

If you do not have a fax machine, you can call the Government Forms Distribution Center at

1-800-418-FORM and request that the form and instructions be mailed to you.

FCC Part 90 Rules

You must be familiar with Part 90 of FCC Rules before you operate your transceiver. The

operation instructions in this manual conform to Part 90, but do not cover all items in Part

90.

Overall, Part 90 states that:

!You must have a valid license before you use the transceiver.

!As licensee, you are responsible for proper operation of all transceivers operating under

your license’s authority.

!You can let unlicensed persons operate transmitter, as long as you take precautions to

prevent unauthorized transmissions.

!You must use this transceiver only for commercial use of your business, and only when

other commercial channels (such as the telephone) are either not available or not

practical.

!You must always yield the operating frequency to communications that involve the

safety of life or property.

!You must take reasonable precautions to prevent harmful interference to other services

operating on the same frequency.

!You must not transmit program material of any kind used in connection with commercial

broadcasting.

!You must not provide a service that is normally handles by telephone or telegraph

unless such broadcasts involve the safety of life and property or in emergencies such

as an earthquake, hurricane, flood or a similar disaster where normal communications

channels are disrupted.

!During each transmissions or exchange of transmissions, you must identify your station

with the call sign issued to you by the FCC, or once each 15 minutes during periods of

continuous operation.

!You must keep a written record of any maintenance or modifications made to the

transceiver, and you must make this record available for inspection upon demand by

the FCC.

Violating any of the provisions of Part 90 can result in fines and/or confiscation of

equipment.

Your transceiver might cause TV or Radio interference even when it is operating properly.

To determine whether your transceiver is causing the interference, turn off your transceiver.

If the interference goes away, your transceiver us causing it. Try to eliminate the

interference by:

!Moving your transceiver away from the receiver

!Contacting your local RadioShack store for help

If you cannot eliminate the interference, the FCC requires that you stop using your

transceiver.

ADDITIONAL FCC REGULATIONS

The Business Radio Service is under the jurisdiction of the FCC. Any adjustments or

alterations that would alter the performance of the transceiver so it no longer meets the

original FCC type acceptance or would change the frequency-determining method are

strictly prohibited.

Replacement or substitution of crystals, transistors, ICS, regulator diodes, or any other

component that is of a unique nature with components other than those recommended can

violate the technical regulations of the FCC rules or violate type acceptance requirement of

the rules.

Before you operate the transceiver, you must obtain your license. It is illegal to transmit

without the appropriate license, which you can get by submitting a completed FCC Form

600 to the FCC (or through the PCIA). Furthermore, your are required to understand Part 90

of the FCC Rules and Regulations prior to operating your transceiver. It is the user’s

responsibility to see that this unit is operating at all times in accordance with the FCC Rules

and Regulations.

USING THE RADIO

A. DISPLAY

Your radio comes with a multifunctional backlight display. By pressing any button except

the PTT, the backlight will illuminate for 5 seconds. The liquid crystal display has been

enlarged to show all of the operating modes.

1. Shows the selected channel number.

2. Shows the selected privacy code number.

3. “FUNC”: Displays when the secondary function is enabled.

4. “SCAN”: Displays when the scan mode is activated.

5. “TX”:Displays when your radio is transmitting.

6. “BUSY”: Displays when a call is being received.

7. “LOCK”: Displays when the keypad lock is activated.

8. “QUIET”: Displays when the QUIET mode is enabled.

9. “C-TONE”: Displays when the Roger Beep function is activated.

10. “HI LO”: Displays when the Hi/Lo transmit power is toggled.

11. “ ”: Indicates the batteries are low. Replace the batteries when it appears

12. “ ”:Displays when the working channel is set to be skipped.

13. “ ”: Displays when the key tone function is activated.

B. FUNCTION AND LOCATION OF THE CONTROLS

1. “ON/OFF” Volume Control.

In “OFF” position, your transceiver is off. Rotate this control clockwise to turn on your radio

and adjusts the volume, until you get a comfortable listening level.

2. SQL Knob

You can turn VOL/SW Knob to obtain the squelch sensitivity at threshold.

3. CH /Key Tone Button

Press CH to move one channel higher. Press and hold CH for more than 1.5sec to

enter into the scan upwardly mode. Press CH will change the scanning direction

downwardly. During the scanning, press any key will exit the scanning mode.

Key Tone

Press and hold FUNC key, then press CH key to activate or deactivate the Key Tone

function. Icon “ ” will be shown if activated.

4. CH / Skip

Press CH to move one channel down. Press and hold CH for more than 1.5sec to

enter into the scan downwardly mode. Press CH will change the scanning direction

upwardly. During the scanning, press any key will exit the scanning mode.

Skip

User can choose a desired channel from being scanned. Press CH or to go to the

desired channel. Press and hold FUNC key for, then press CH key to skip this channel

from scanning. Icon “ ” is on to indicate this working channel is set to be skipped. Repeat

the above steps will cancel the skip function of the channel.

Automatic Power Off Button

Press and hold FUNC/MON button, then press HI/LO button to enable or disable the auto

power off function. The display will show “AP ON” or “AP OF” for one second, when the timer

is activated/deactivated. The timer automatically turns off the unit when it is idle for 2 hours.

5. QUIET /QUIET Scan Button/Reset

Press QUIET button to enable or disable the QUIET privacy mode operation.

a) Hold down

QUIET button for 1.5 seconds until QUIET is displayed and the quiet code

flashes.

b) Repeatedly press (or hold down) CH or CH until you see the code number you

want to use.

c) Press

QUIET button to store the code.

6. Hi/Lo / Automatic Power Off Button

Press this button to toggle the high or low RF power.

Automatic Power Off Button

Press and hold FUNC/MON button, then press HI/LO button to enable or disable the auto

power off function. The display will show “AP ON” or “AP OF” for one second, when the

timer is activated/deactivated. The timer automatically turns off the unit when it is idle for 2

hours.

To turn on the quiet feature, press QUIET, QUIET icon appears. To turn off the feature,

press QUIET until QUIET disappears.

Note: We recommend that you select a quiet code from the range 7-30. If you select a

code below or above that range, you must wait 1 to 2 seconds after holding down PUSH-

TO-TALK before you start talking.

QUIET Scanning (Only available under QUIET mode)

Press and hold FUNC key, and follow by QUIET key to enter into the QUIET Scan mode,

and icons of “SCAN” and “QUIET” will be lightened on LCD. When received the same

QUIET code, the scanning stops and will keep scanning after the signal disappears. Press

any key will exit and return to the normal working channel.

Reset

To reset the unit, press and hold the QUIET key and turn on the unit. Reset operation will

clean all the set channels and restore the current channel to CH2 with QUIET off. Power is

toggled to low mode, key tone and C-tone function are activated.

6. Push-To-Talk button / Keylock /C-Tone

To talk, hold down the Push-To-Talk. Speak into the microphone in a normal tone of voice

when the TX icon is displayed. When you finish speaking, release the Push-To-Talk

button.

Your can also lock your radio setting to avoid accidental pressing of keys by activating the

keypad lock. Press and hold the FUNC button, then press the PTT button to activate or

deactivate the keypad lock.

Press and hold the Push-To-Talk while turning on the radio will enable or disable the

courtesy tone (C-Tone) function.

7. MON/FUNC Button

To hear everything happening on a channel, including weak transmission, hold down

MON/FUNC button for more than 1.5 sec. Re lease the MON/FUNC button to turn the

auto-squelch back on.

8. External Mic/Spk Jack

Connect an optional speaker/microphone or earphone in this jack.

9. Charger Jack

You can recharge battery pack using the supplied battery charger. Plug the charger’s

barrel plug into the CHRG jack on the side of the unit, then connect the charger to a

standard AC outlet.

10.Rechargeable Battery Pack

You can recharge the battery pack using supplied the battery charger.

11.Belt Clip

To attach the belt clip, place it over the locking pin and align the screw hole. Tighten the

screw.

12.Antenna

Provides excellent reception.

C. Major Channel Set Up

The user can set up total of 8 channel (Refer to UHF Business Band Frequency Table)

1. If the unit is on, turn the unit off. Press Hi/Lo and QUIET key together and hold while

turn on the unit, the channel number then will flash. The radio enters channel setup

mode. The icon ON or OFF on the top right corner indicates the channel is selected or

not.

2. Use or key to select a channel.

3. When a channel is selected, press PTT key to confirm the selected channel. Channel

number stop flashing and at the display the top right icon is changed from OF to ON.

PTT

4. Press and hold the QUIET key for 1.5sec to enter CTCSS channel setting-up mode.

The working QUIET channel number is flashing.

5. Use or key to select the desired QUIET channel.

6. When the

QUIET channel is selected, press QUIET key to confirm and exit the QUIET

setting mode.

7. Repeat step 1 to 6 to set up other channel, total of 8 channels can be set up.

8. When all channels are selected, press FUNC key or no key entry for 5 seconds to

confirm and exit the channel set-up mode.

Note:

1. When setting the channels, the user may omit the steps of 4-6, and the channels are

set without QUIET codes.

2. When total 8 channels are already set up, user should OF one channel before setting

another channel. Otherwise, press PTT to select the desired channel will not succeed

and a beep sound will be heard.

To reset the unit, press and hold the QUIET key and turn on the unit. Reset operation will

clean all the set channels and restore the current channel to CH2 without QUIET code.

C. OPERATION

1. Please charge the battery pack with the supplied charger.

Ni-Cd batteries must be charged for a minimum of 10 hours before initial use.

2. Turn VOL control knob to the unit “on”. Turn the SQL knob counterclockwise to the end,

and adjust the volume to a normal listening level.

3. Turn SQL knob clockwise until background noise is just quieted.

4. Select the desired channel and/or QUIET privacy code.

5. Press Push-To-Talk button to transmit.

6. To receive, simply release Push-To-Talk button.

Note: You can only communicate with another radio that is using the same channel and/or

the same QUIET privacy code as your radio.

TECHNICAL SPECIFICATIONS

Inhaltsverzeichnis

Andere Radio Shack Zwei-Wege-Funkgerät Handbücher

Radio Shack

Radio Shack 21-1826/28/29 Bedienungsanleitung

Radio Shack

Radio Shack 21-1904 Bedienungsanleitung

Radio Shack

Radio Shack 22 Ch GMRS/FRS Two way radio Bedienungsanleitung

Radio Shack

Radio Shack TRC-232 Bedienungsanleitung

Radio Shack

Radio Shack 60-3067 Bedienungsanleitung

Radio Shack

Radio Shack Deluxe 2-Way Personal FRS Radio Bedienungsanleitung

Radio Shack

Radio Shack 21-1864 Bedienungsanleitung

Radio Shack

Radio Shack 21-1809 Bedienungsanleitung

Radio Shack

Radio Shack TRC-488 Bedienungsanleitung

Radio Shack

Radio Shack 21-1935 Bedienungsanleitung

Radio Shack

Radio Shack TRC-512 Bedienungsanleitung

Radio Shack

Radio Shack FRS-101 Bedienungsanleitung

Radio Shack

Radio Shack 21-1599 Bedienungsanleitung

Radio Shack

Radio Shack 21-1936 - Gmrs/frs Radios Bedienungsanleitung

Radio Shack

Radio Shack TP-396 Bedienungsanleitung

Radio Shack

Radio Shack 22 Ch GMRS/FRS Two-way Radios Bedienungsanleitung

Radio Shack

Radio Shack TRC-236 Bedienungsanleitung

Radio Shack

Radio Shack 21-1905 Bedienungsanleitung

Radio Shack

Radio Shack Mobile/Marine 14-Channel FRS Radio Bedienungsanleitung

Radio Shack

Radio Shack TRC-509 Bedienungsanleitung

Radio Shack

Radio Shack BUZZBUGGS 21-1848/1888 Bedienungsanleitung

Radio Shack

Radio Shack 21-1901 Bedienungsanleitung

Radio Shack

Radio Shack TRC-92 Bedienungsanleitung

Radio Shack

Radio Shack 5W Bedienungsanleitung

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

Midland

Midland 70-1526A/B Bedienungsanleitung

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Midland

Midland MXT275J Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung