RAK RAK7268 Bedienungsanleitung
Documentation Center
RAK7268 Quick Start Guide
Prerequisites
What Do You Need?
1. RAK7268/RAK7268C WisGate Edge Lite 2
2. Ethernet Cable (RJ-45 Port) – for Ethernet connection
3. A Windows/MacOS/Linux computer
⚠
WARNING
The SIM card slot of the cellular versions is not hot-swappable. Make sure the gateway is switched off
before inserting or ejecting the SIM card.
Product Configuration
Power on the Gateway
1. Attach the LoRa Antenna.
First and foremost, screw on the antenna to the RP-SMA connector on the back panel of the RAK7268/C WisGate
Edge Lite 2.
p
WARNING
Do not power the device if the LoRa Antenna port has been left open to avoid potential damage to the
RAK7268/RAK7268C WisGate Edge Lite 2.
2. Power the gateway ON.
It is recommended to use the 12 V DC adapter that comes with the RAK7268/RAK7268C WisGate Edge Lite 2.
Optionally, you can use your own PoE cable and injector since the device supports PoE.
Casing and Ports
Figure 1: RAK7268/C WisGte Edge Lite 2 Top View
Documentation Center
Figure 2: RAK7268/C WisGate Edge Lite 2 Back Panel
Status LED Indicators
LEDs Status Indication Description
PWR LED Power indicator - The LED is on when the device powered.
Breathing LED Breathing after system is up
ETH LED
ON - Link is up
OFF - Link is down
Flicker - Ongoing data transfer
LoRa LED
ON - LoRa is up
OFF - LoRa is down
Flicker - Ongoing data transfer
WLAN LED
AP Mode:
- ON - The AP is up
- OFF - The AP is down
- Flicker - Ongoing data transfer
STA Mode:
- Slow flicker (1 Hz) - Disconnected
- ON - Connected
- Flicker - Ongoing data transfer
LTE LED (will light up only on Slow flicker (1800 ms High / 200 ms Low) - Network searching
Documentation Center
RAK7268C) Slow flicker (200 ms High / 1800 ms Low) - Idle
Fast flicker (125 ms High / 125 ms Low) - Ongoing data
transfer
Reset Key Functions
The functions of the Reset key are as follows:
1. Short press - Restarts the gateway.
2. Long press (5 seconds and above) - Restores factory settings.
Access the Gateway
In this section, several ways of accessing the gateway are provided to have different alternatives for you to choose
from depending on the availability of the requirements needed.
⚠
WARNING
Do not power the device if the LoRa Antenna port has been left open to avoid potential damage to the
RAK7268/RAK7268C WisGate Edge Lite 2.
Wi-Fi AP Mode
By default, the gateway will work in Wi-Fi AP Mode which means that you can find an SSID named
RAK7268_XXXX on your PC's Wi-Fi Network List. XXXX is the last two bytes of the gateway's MAC address.
📝
NOTE:
No password is required to connect via Wi-Fi
Using your preferred Web browser, log in with the credentials provided below:
Browser Address: 192.168.230.1
Username: root
Password: root
WAN Port (Ethernet)
Connect the Ethernet cable to the port marked ETH on the gateway and the other end to the PoE port of the PoE
injector. Connect the LAN port of the PoE injector to your PC.
The default IP is 169.254.X.X. The last two segments (X.X) are mapped from the last four bits of the MAC address
of your gateway.
For example, the last four bits of the MAC address are 0F:01, and the IP address is 169.254.15.1. Make sure to
manually set the address of your PC to one in the same network (for example 169.254.15.100). Use the same
credentials for the Web UI as for AP mode.
Documentation Center
Figure 3: Web UI Login Page
Access the Internet
Connect through Wi-Fi
Go into the Network>Wi-Fi menu and make sure to select Client in the Mode field. Enter or click "Scan" to
choose your ESSID, select the right Encryption method and enter the correct Key.
Figure 4: Connect through Wi-Fi Credentials
📝
NOTE:
Assuming you have entered the correct parameter values you should get an IP address assigned by your
Wi-Fi router's (AP) built-in DHCP server. You can use this new IP address to log in via a web browser
(same way as in AP mode).
Connect through Ethernet
Connect the one end of the Ethernet cable to the Ethernet on the Gateway and the other end to your router. The
router’s DHCP server should assign an IP Address to the Gateway. You can change the default settings below if
Inhaltsverzeichnis
Andere RAK Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
