R&S RTO2000 Bedienungsanleitung

R&S®RTO2000

Oscilloscope

Getting Started

1332971902

(=PïC2)

Getting Started

Version 10

Sie haben Fragen oder wünschen eine Beratung? Angebotsanfrage unter 07121 / 51 50 50 oder über [email protected]

Distributed by:

This manual describes the following R&S®RTO models with firmware version 4.75

and higher:

●R&S®RTO2002 (1329.7002K02)

●R&S®RTO2004 (1329.7002K04)

●R&S®RTO2012 (1329.7002K12)

●R&S®RTO2014 (1329.7002K14)

●R&S®RTO2022 (1329.7002K22)

●R&S®RTO2024 (1329.7002K24)

●R&S®RTO2032 (1329.7002K32)

●R&S®RTO2034 (1329.7002K34)

●R&S®RTO2044 (1329.7002K44)

●R&S®RTO2064 (1329.7002K64)

Mühldorfstr. 15, 81671 München, Germany

Phone: +49 89 41 29 - 0

Email: [email protected]

Internet: www.rohde-schwarz.com

Subject to change – Data without tolerance limits is not binding.

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.

Trade names are trademarks of the owners.

1332.9719.02 | Version 10 | R&S®RTO2000

Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g.

R&S®RTO2000 is indicated as R&S RTO.

Contents

R&S®RTO2000

3Getting Started 1332.9719.02 ─ 10

Contents

1 Safety and Regulatory Information...................................... 5

1.1 Korea Certification Class A..................................................................6

2 Key Features.......................................................................... 7

3 Documentation Overview......................................................8

3.1 Manuals and Instrument Help..............................................................8

3.2 Data Sheet and Brochure..................................................................... 9

3.3 Release Notes, Open Source Acknowledgment.............................. 10

3.4 Application notes, Application cards, Videos.................................. 10

4 Preparing for Use.................................................................11

4.1 Unpacking and Checking the Instrument......................................... 11

4.2 Positioning the Instrument................................................................ 12

4.3 Starting the Instrument...................................................................... 14

4.4 Connecting External Devices............................................................ 16

5 Instrument Tour................................................................... 20

5.1 Front Panel.......................................................................................... 20

5.2 Rear Panel........................................................................................... 23

5.3 Keys and Controls.............................................................................. 27

6 Trying Out the Instrument...................................................39

6.1 Displaying a Basic Signal.................................................................. 39

6.2 Acquiring Data.................................................................................... 41

6.3 Organizing the Display....................................................................... 43

6.4 Changing the Waveform Scaling and Position................................ 46

6.5 Zooming into the Display................................................................... 50

6.6 Displaying the Waveform History......................................................53

Contents

R&S®RTO2000

4Getting Started 1332.9719.02 ─ 10

6.7 Performing Basic Measurements...................................................... 55

6.8 Performing a Basic FFT Analysis......................................................65

6.9 Performing Mathematical Calculations.............................................68

6.10 Performing a Search...........................................................................69

6.11 Performing a Mask Test......................................................................71

6.12 Printing and Saving Screenshots......................................................74

6.13 Saving Data......................................................................................... 77

7 Operating the Instrument....................................................80

7.1 Means of Manual Interaction..............................................................80

7.2 Touchscreen Display.......................................................................... 81

7.3 App Cockpit.........................................................................................87

7.4 Working with Waveforms................................................................... 88

7.5 Rohde & Schwarz SmartGrid............................................................. 91

7.6 Toolbar................................................................................................. 92

7.7 Displaying Results............................................................................101

7.8 Using Dialog Boxes.......................................................................... 103

7.9 Entering Data.....................................................................................105

7.10 Messages...........................................................................................107

7.11 Getting Information and Help.......................................................... 108

8 Setting Up the Instrument................................................. 111

8.1 Performing a Self-alignment............................................................ 111

8.2 Aligning the Touchscreen................................................................ 112

8.3 Setting the Display Language..........................................................112

8.4 Adjusting Passive Probes................................................................ 113

9 Contacting Customer Support..........................................114

Index....................................................................................115

Safety and Regulatory Information

R&S®RTO2000

5Getting Started 1332.9719.02 ─ 10

1 Safety and Regulatory Information

The R&S RTO oscilloscope is designed for measurements on circuits that are

only indirectly connected to the mains or not connected at all. It is not rated for

any measurement category.

The instrument is rated for pollution degree 2 - for indoor, dry location use where

only non-conductive pollution occurs. Temporary conductivity caused by conden-

sation is possible.

The instrument must be controlled by personnel familiar with the potential risks of

measuring electrical quantities. Observe applicable local or national safety regula-

tions and rules for the prevention of accidents.

Safety information is part of the product documentation. It warns you about the

potential dangers and gives instructions how to prevent personal injury or dam-

age caused by dangerous situations. Safety information is provided as follows:

●The "Basic Safety Instructions" in different languages are delivered as a prin-

ted brochure with the instrument.

●Throughout the documentation, safety instructions are provided when you

need to take care during setup or operation.

Safety instructions

To prevent electric shock, personal injury or fire, follow these rules:

●Do not open the instrument casing.

●Do not use the instrument if you detect or suspect any damage of the instru-

ment or accessories.

●Do not operate the instrument in wet, damp or explosive atmospheres.

●Make sure that the instrument is properly grounded.

●Do not use the instrument to ascertain volt-free state.

●Do not exceed the voltage limits given in Chapter 5.1.1, "Input Connectors",

on page 21.

Safety and Regulatory Information

R&S®RTO2000

6Getting Started 1332.9719.02 ─ 10

1.1 Korea Certification Class A

이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하

시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.

Korea Certification Class A

Key Features

R&S®RTO2000

7Getting Started 1332.9719.02 ─ 10

2 Key Features

The R&S RTO oscilloscopebrings various benefits in your daily work. Outstanding

key features are:

Best oscilloscope performance

●Up to 16-bit vertical resolution

●Trigger on any detail you can see

●Quickly find signal faults with 1 Million waveforms/s

●Integrated spectrum analysis

Widest range of capabilities

●Fast acquisition rate even with industry leading 2 Gsample deep memory

●First zone trigger in time and frequency domain

●Analyze previous acquisitions - always available in history buffer

●Deep toolset for signal analysis

Powerful user interface

●High-resolution 12.1’’ capacitive touchscreen with gesture support

●Easily customizable waveform display with SmartGrid

●Fast access to important tools

●Documentation at the press of a button

Engineered for multi-domain challenges

●Class leading MSO

●Trigger and decode for serial protocols

●Power measurements

●Automatic compliance tests

●EMI debugging with oscilloscopes

●IQ and RF analysis

●Extensive probe portfolio for voltage, current and more

For a detailed specification refer to the data sheet.

Documentation Overview

R&S®RTO2000

8Getting Started 1332.9719.02 ─ 10

3 Documentation Overview

This section provides an overview of the R&S RTO user documentation.

3.1 Manuals and Instrument Help

You find the manuals on the product page at:

www.rohde-schwarz.com/manual/rto

Getting started manual

Introduces the R&S RTO and describes how to set up and start working with the

instrument, and describes basic operations. A printed English version is included

in the delivery. Editions in other languages are available on the product website.

Instrument help

The help offers quick, context-sensitive access to the complete information for the

firmware basic functionality and applications.

User manual (Instrument)

Describes all instrument functions in detail. It also provides an introduction to

remote control, a complete description of the remote control commands with pro-

gramming examples, and information on maintenance and instrument interfaces.

Includes the contents of the getting started manual.

The online version of the user manual provides the complete contents for immedi-

ate display on the internet.

Manuals for compliance test options

For compliance test options, extra test procedure manuals are available. Test fix-

tures are described in printed manuals, which are delivered with the fixture.

●The following test procedure manuals are available:

– USB 2.0 Compliance Test Procedures

– Ethernet Compliance Tests Procedures

– MIPI D-PHY Compliance Tests Procedures

Manuals and Instrument Help

Documentation Overview

R&S®RTO2000

9Getting Started 1332.9719.02 ─ 10

– eMMC Compliance Tests Procedures

– PCIe Compliance Tests Procedures

– DDR3 Compliance Tests Procedures

– ScopeSuite Automation

●The following test fixture manuals are available:

– R&S RT-ZF1 USB 2.0 Compliance Test Fixture Set

– R&S RT-ZF2 Ethernet Compliance Test Fixture Set

– R&S RT-ZF3 Frequency Converter Board (100BASE-T1)

– R&S RT-ZF4 10BASE-Te Test Fixture

– R&S RT-ZF5 Ethernet Probing Fixture

– R&S RT-ZF6 Frequency Converter Board (1000BASE-T1)

– R&S RT-ZF7 Automotive Ethernet T&D Fixture

– R&S RT-ZF7A SMA Adaptor

– R&S RT-ZF8 Automotive Ethernet Compliance Test Fixture

Basic safety instructions

Contains safety instructions, operating conditions and further important informa-

tion. The printed document is delivered with the instrument.

Instrument security procedures manual

Deals with security issues when working with the R&S RTO in secure areas.

Service Manual

Describes the performance test for checking the rated specifications, module

replacement, firmware update, troubleshooting and fault elimination, and contains

mechanical drawings and spare part lists. The service manual is available for reg-

istered users on the global Rohde & Schwarz information system (GLORIS,

https://gloris.rohde-schwarz.com).

3.2 Data Sheet and Brochure

The data sheet contains the technical specifications of the R&S RTO. It also lists

the options with their order numbers and optional accessories. The brochure pro-

vides an overview of the instrument and deals with the specific characteristics.

Data Sheet and Brochure

Documentation Overview

R&S®RTO2000

10Getting Started 1332.9719.02 ─ 10

See www.rohde-schwarz.com/brochure-datasheet/rto

3.3 Release Notes, Open Source Acknowledgment

The release notes list new features, improvements and known issues of the cur-

rent firmware version, and describe the firmware installation. The open source

acknowledgment document provides verbatim license texts of the used open

source software. It can also be read directly on the instrument.

See www.rohde-schwarz.com/firmware/rto.

3.4 Application notes, Application cards, Videos

These documents deal with special applications or background information on

particular topics.

See www.rohde-schwarz.com/application/rto and Oscilloscopes Application Vid-

eos - Media Center

Application notes, Application cards, Videos

Andere Handbücher für RTO2000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere R&S Prüfgeräte Handbücher

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung