Ranger design 1050-FS Bedienungsanleitung
INSTALLATION GUIDE
1050-FS INSIDE LADDER CARRIER
Inside Ladder Carrier ( Aluminum )
QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
q1.1 Setup...............................................................................................................................................
q1.2 Ladder Carrier Assembly.................................................................................................................
3 - 4
5 - 7
Phase 1 - Assembly
Phase 2 - Installation
qCordless Impact
qTape Measure
qLadder
q1/2" Socket
q7/16" Socket
q3/8" Impact Bit
qKnife
q2.1 Ladder Carrier Installation................................................................................................................ 8 - 9
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
10-550 Mounting Track ( 96" Long ) 1
10-551 Front Support 1
10-552 Rear Support 1
10-553 Support Carrier 1
10-554 Channel Bracket 2
10-557 End Cap 2
10-559 Elastic Clamp 1
10-5002 Support Carrier Sub-Assembly 1
94-1018 Assembly Fastener Kit 1
96-1024 Install Fastener Kit 1
BILL OF MATERIALS
10-557 10-554 10-559
10-552
10-553
10-550
10-5002
10-551
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 4
94-1018 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
96-1024 Fastener Kit Fastener Assembly
8×8×
#90-392 Carriage Bolt 1/4" × 3/4"
#94-106 Lock Nut
#98-106 Flat Washer
1×1×
#90-208 Hex Bolt 5/16" × 1"
#98-122 Lock Washer
#98-116 Flat Washer
#94-150 Channel Nut
# 90-392
8×8×
Carriage Bolt
1/4"-20 × 3/4"
ZINC
# 98-106
Flat Washer
1/4"
ZINC
8×8×
# 94-106
Lock Nut
1/4"
ZINC
8×8×
# 98-122
1×1×
Lock Washer
5/16"
ZINC
# 90-208
1×1×
Hex Bolt
5/16"-18 × 1"
ZINC
# 94-150 Channel Nut
5/16"
1×1×
Flat Washer
5/16", 7/8" OD
ZINC
# 98-116
1×1×
# 92-100
Hex Screw
#14 × 3/4"
ZINC
4×4×
# 92-102
Hex Screw
#14 × 1"
ZINC
2×2×
4×4×
#92-100 Hex Screw 3/4"
2×2×
#92-102 Hex Screw 1"
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 5
1.2.1 Attach the rear and front supports to the support carrier.
PHASE 1 – ASSEMBLY
1.2 LADDER CARRIER ASSEMBLY
HARDWARE USED
8× hand-tighten the nuts.
#90-392 Carriage Bolt 1/4" × 3/4"
#94-106 Lock Nut
#98-106 Flat Washer
FRONT
REAR
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 6
1.2.2 Attach the end caps on both ends of mounting track.
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 7
1.2.3 Clamp the loose end of the elastic strap to the mounting track, using the elastic clamp as shown.
NOTE: Elastic strap length = Step ladder length - 5" ( max. 70")
#90-208 Hex Bolt 5/16" × 1"
#98-122 Lock Washer
#98-116 Flat Washer
#94-150 Channel Nut
HARDWARE USED
1× hand-tighten the nuts.
TOOLS
qCordless Impact
q1/2" Socket
qTape Measure
step ladder length - 5"
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 8
PHASE 2 – INSTALLATION
2.1 LADDER CARRIER INSTALLATION
2.1.1 Install the ladder carrier on the roof beams with the channel bracket to hold the mounting tracks.
NOTE: Make sure that the mounting track is not blocking or touching the partion on the top.
1"
#92-100 Hex Screw 3/4"
2×2×
#92-102 Hex Screw 1"
HARDWARE USED
2×
TOOLS
qCordless Impact
q3/8" Impact Bit
#92-100 Hex Screw 3/4"
HARDWARE USED
2×
TOOLS
qCordless Impact
q3/8" Impact Bit
FRONTREAR picture shown sprinter roof
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 9
FRONTREAR picture shown sprinter roof
TOOLS
qCordless Impact
q7/16" Socket
TOOLS
qCordless Impact
q7/16" Socket
2.1.2 Place the ladder on the carrier and adjust the supports as needed, then tighten the lock nut.
HARDWARE USED
4× hardware are already attached
#90-392 Carriage Bolt 1/4" × 3/4"
#94-106 Lock Nut
#98-106 Flat Washer
HARDWARE USED
4× hardware are already attached
#90-392 Carriage Bolt 1/4" × 3/4"
#94-106 Lock Nut
#98-106 Flat Washer
For technical support, contact us at 1-800-565-5321 1050-FS Installation Guide |REV. D2 | Page 10
“You have successfully installed your
Inside Ladder Carrier
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: cs@rangerdesign.com
Inhaltsverzeichnis
Andere Ranger design Rack & Stand Handbücher
Ranger design
Ranger design 76-U1236 Bedienungsanleitung
Ranger design
Ranger design C5-BA13-4 Bedienungsanleitung
Ranger design
Ranger design 1530-NL Bedienungsanleitung
Ranger design
Ranger design 84-U0063 Bedienungsanleitung
Ranger design
Ranger design MAX RACK 2.0 Bedienungsanleitung
Ranger design
Ranger design S2-RS60-2 Bedienungsanleitung
Ranger design
Ranger design C4-BA11-4 Bedienungsanleitung
Ranger design
Ranger design 1530-NSX Bedienungsanleitung
Ranger design
Ranger design C4-BA11-3 Bedienungsanleitung
Ranger design
Ranger design C4-BA13-3 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
