Ratek BTR5-12V Bedienungsanleitung

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 1 of 16

User Manual

Tube Roller Mixer

Model : BTR5-12V / BTR10-12V

Version: 1.1 – 05/06/2015

En lish

www.ratek.co .au

60 Wadhurst Dve, Boronia, Victoria 3155, Australia - P: +613 9887 2161 - F: +613 9887 2163 - E: [email protected]om.au

Made in Australia, User Manual printed in Australia

Chan es without prior notification reserved

Errors and omissions excepted.

User Manual BTR5-12V / BTR10-12V – Tube Roller Mixer

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 2 of 16

Thank you

Thank you for purchasin a Ratek product.

This User Manual will assist you in the correct installation and operation of the Tube Roller Mixer, as well as explain the safety requirements for its

use.

I portant: Please read the contents of this User Manual before unpacking and operating the product.

Unpacking and Checking

Once you have read these instructions in full and understand the installation and safety requirements includin those for unpackin the carton, please

carefully open the packin and slowly remove the product. Carefully inspect the condition of the product to ensure it has not been dama ed in

transit. Any dama e should be reported immediately to the responsible carrier. If the product is dama ed in any way, re-pack the product into the

supplied packa in and notify the responsible carrier immediately.

I portant: Do not operate the equip ent if it has been da aged in any way. Any failures resulting through the use of a da aged product

will not be covered by the product warranty.

Carton Contents

Ensure that you have received all items outlined below before proceedin . If you have not received all components in the supplied carton, please re-

pack the carton and notify a Ratek Service representative immediately. Contact details are provided in the section of this User Manual titled “Ratek

Service Contact Information”

-Ratek BTR Tube Roller Mixer

-12V Power Supply with Lead

-User Manual

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 3 of 16

TABLE OF CONTENTS

PAGE

Cash Bo

INTENDED USE................................

................................................................

.....................................

..........

..... 4

44

4

Suitable Articles For Use With This Tube Roller Mixer ..................................................................................................................... 4

Unsuitable Articles For Use With This Tube Roller Mixer .................................................................................................................. 4

Suitable Environments For The Tube Roller Mixer........................................................................................................................... 4

General Operation .................................................................................................................................................................. 4

OPERATOR RESPONSIBILITY – SAFETY CONSIDERATIONS ................................

................................................................

..............................................

............................

.............. 4

44

4

Conditions of Operation............................................................................................................................................................ 4

Safety Labels And Markin s ...................................................................................................................................................... 5

OPERATING PROCEDURES................................

................................................................

.......................................................

..............................................

....................... 5

55

5

Identification of Controls & Functions .......................................................................................................................................... 6

Safety Warnin s..................................................................................................................................................................... 7

Safety Recommendations .........................................................................................................................................................7

Preparation & Installation.........................................................................................................................................................8

Usin The Tube Roller Mixer...................................................................................................................................................... 9

ROUTINE CLEANING AND MAINTENANCE................................

................................................................

.................................

..

. 11

1111

11

TECHNICAL SPECIFICATIONS ................................

................................................................

.................................................

..................................

................. 13

1313

13

DISPOSAL................................

................................................................

.........................................

..................

......... 13

1313

13

EMC CONFORMITY ................................

................................................................

.............................................................

..........................................................

............................. 13

1313

13

RATEK SERVICE CONTACT INFORMATION ................................

................................................................

.................................

..

. 14

1414

14

TROUBLESHOOTING................................

................................................................

.............................................................

..........................................................

............................. 14

1414

14

WARRANTY CONDITIONS ................................

................................................................

.....................................................

..........................................

..................... 15

1515

15

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 4 of 16

Intended Use

This Tube Roller Mixer is intended for the purpose of a itatin vessels containin liquid to create a rollin mixin action inside the vessel.

The Tube Roller Mixer is not intended to provide direct-contact between itself and an unprotected medical, food, biolo ical or medico- techno item. In

all cases the item should be enclosed in a suitable vessel as described below.

Suitable Articles For Use With This Tube Roller Mixer

•Plastic or lass laboratory test tubes that are sealed and rated to withstand the intended velocity of a itation.

•Plastic or lass laboratory sample vials or bottles that are sealed and rated to withstand the intended velocity of a itation.

•

An example of a suitable article would be a sealed laboratory tube filled with blood

Unsuitable Articles For Use With This Tube Roller Mixer

•Any item where the article is not sealed or durin mixin may result in its contents comin into contact with the Tube Roller Mixer or

the Operator.

•Items wei hin more than 1000 rams.

•

An example of an unsuitable article would be an open ended test tube filled with blood. The tube should be sealed with a suitable cap

or stopper.

Suitable Environ ents For The Tube Roller Mixer

The Tube Roller Mixer is intended for use in a clean laboratory environment only where adequate ventilation, a ood power supply and

provisions for routine cleanin are available. The Tube Roller Mixer should not be used outdoors or in dirty, dusty, humid or windy

environments. The acceptable operatin conditions are outlined further in this User Manual.

General Operation

•The Tube Roller Mixer is plu ed into an appropriate power source. It is powered by an alternatin current power supply with the

appropriate receptacle, rated volta e and frequency for the country of its intended use. Further details on power requirements are

outlined in this User Manual.

•A suitable article (as defined above) is placed onto the rollers

•The Tube Roller Mixer is operated via a top panel interface consistin of a power switch and a mixin speed control knob. These

controls allow the operator to set a required rollin speed.

•The Tube Roller Mixer should be operated strictly in accordance with the Operatin Procedures outlined further in this User Manual.

Operator Responsibility – Safety Considerations

When operated in strict accordance with this User Manual, plus routine cleanin and maintenance bein carried out, the product shall provide safe

operation for the operator. The operator should be aware of the followin before installin and operatin the product:

Conditions of Operation

*Note: The term “Operator” referred to in this User Manual is the primary person who has been tasked to install, maintain and train in the

usa e of this equipment. Other personnel shall be referred to as “Users”.

•The operator shall be aware that the protection provided by the equipment may be impaired if the equipment is used with accessories

not provided or recommended by the manufacturer, is modified in any way or is used in a manner not specified by the manufacturer.

•The operator is responsible for ensurin all users of the product are qualified to do so, and are well versed in common safety

concepts. The product should only be operated by an adult who has read and understood this User Manual provided in the appropriate

lan ua e in its entirety.

•Any user must be informed by the responsible operator of any potential hazards that may arise throu h the use of this equipment in

the course of their work, includin any local environmental hazards not related directly to the Tube Roller Mixer. They should also be

able to demonstrate that they understand any preventative safety measures in operation prior to operatin the equipment.

•The operator shall a ree to accept responsibility for the use of the equipment in accordance with this User Manual, and be fully aware

that the equipment is desi ned for commercial use.

•It is assumed that the user and operator have had experience in a commercial environment, and had appropriate trainin in how to

perform their work safely in accordance with any local operational health and safety re ulations. The operator and all users should be

well versed in local emer ency procedures as per the workplace safety re ulations in effect.

•Avoid any direct impact with any surface of the equipment, includin the casin , disc and most importantly the control panel.

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 5 of 16

•I portant: Do not use any sharp or pointed metal objects anywhere near the equipment, in particular the control panel.

•Avoid usin the equipment near any other vibratin equipment or source of excessive vibration.

•Ensure the equipment is cleaned and maintained in accordance with this User Manual.

•Ensure that all ori inal safety warnin labels are in an adequate, le ible condition and are firmly affixed to the equipment before usin

the product.

•Plu the equipment directly into a wall power outlet. Do not plu the equipment into a multi-socket adapter of any kind.

•The equipment is intended for operation in a controlled electroma netic environment. Avoid the use of transmittin devices (e. .

cellular or mobile telephones) near the equipment whilst operatin . A minimum distance of 2 Metres from the product is

recommended for any transmittin device.

•The equipment must only be installed and operated in well ventilated areas. The unit is not intended for use in explosive atmospheres

or in confined spaces.

•The allowed operatin environment must be between 0° Celsius and 60° Celsius ambient air temperature.

•The maximum allowed relative humidity of the operatin environment is 80%.

•The equipment should not be stored in direct sunli ht, near chemicals, or other contaminants.

•If any of these safety recommendations cannot be achieved or the equipment has been dama ed in any way, the equipment should not

be installed or operated.

•I portant: If you have any concerns or questions relatin to operator or user safety, please contact the appropriate Ratek Service

department before installin and operatin the unit. Contact details are provided in this User Manual.

Safety Labels And Markings

The equipment is provided with safety caution labels. An explanation of each caution label is provided below. It is the responsibility of the

operator and user to fully understand the meanin of these warnin labels prior to operatin the equipment.

Caution Labels Definition

Colours: Black on a yellow back round

The Tube Roller Shaker has rollin tubes which should not be touched whilst they are

movin . Keep all body parts away from the rollers whilst in operation. Always stop the

rollers usin the top panel speed control before addin or removin any items.

This label is fitted by the manufacturer and must not be removed under any

circumstances.

Operating Procedures

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 6 of 16

You must take the time to familiarize yourself completely with the followin operatin procedures before installin or operatin the Tube Roller Mixer

in order to achieve the best performance and maximum attainable user safety.

Identification of Controls & Functions

Throu hout this User Manual, the numerical element representin a control or component of the Tube Roller Mixer will be used to identify it. The

fi ure below indicates all key controls and components of the Tube Roller Mixer with their correspondin numerical element labeled.

Fi ure 1

Nu erical Ele ent & Description of Co ponent

1Power switch

2Speed control knob

3Rollers

4Power Supply

5Power indicator li ht

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 7 of 16

Safety Warnings

Throu hout this User Manual, specific warnin s will be supplied which relate to the current operation bein referred to. These warnin s are supplied

in addition to the main warnin labels affixed to the product and the key points outlined in the section of this User Manual titled ‘Operator

Responsibility – Safety Considerations’.

A raphical symbol as pictured below will be used next to each warnin with accompanyin text; the dan er level for each is described below:

CAUTION

Indicates a possibly hi hly dan erous situation which may result in serious injury or threat to life if the situation is not avoided.

CAUTION

Indicates a possibly harmful situation which may result in injury or dama e to product or property if the situation is not avoided.

Safety Reco endations

The followin safety recommendations must be followed to prevent dama e or injury. In addition to these safety recommendations, it is assumed

that the user and operator have had experience in a commercial environment, and had appropriate trainin in how to perform their work safely

in accordance with any local operational health and safety re ulations. The operator and all users should be well versed in local emer ency

procedures as per the workplace safety re ulations in effect.

CAUTION

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be

impaired.

CAUTION

A sur e protected power outlet is stron ly recommended as it provides some protection for the equipment in areas of poor

electrical quality as well as providin some protection a ainst li htnin strikes. The equipment should be operated on a ood,

reliable supply of power at all times.

Note: The Tube Roller Mixer should not be operated on the same electrical circuit as other hi h volta e household appliances

such as frid es, clothes dryers, washin machines or other continuous operation hi h volta e devices. These types of devices

can create power fluctuations that are undesirable for electrically sensitive equipment. Consult your workplace administrator or

electrical maintenance staff if you are unsure.

-ALWAYS wear protective eyewear when workin with the equipment.

-ALWAYS place the Tube Roller Mixer on a stron , even, dry, flat, smooth surface to allow the rubber feet to hold the

mixer securely.

-ALWAYS turn off power before movin the equipment to a new location.

-ALWAYS turn off the mains power supply at the outlet when the unit is not in operation.

-ALWAYS be careful of water or other liquids near the workin area and ensure any spills cannot come in contact with the

Tube Roller Mixer control panel or mains power supply. Ensure benches are kept dry at all times.

-ALWAYS operate the Tube Roller Mixer in a well ventilated area with adequate clearance around the Tube Roller Mixer as

indicated in case of spilla e.

-ALWAYS use only the ori inal mains power supply. Replacement non- enuine supplies may not be suitable.

-ALWAYS ensure the equipment is included in your electrical test and ta re ister.

-NEVER operate the equipment if the electrical test ta is out of date.

-NEVER operate the equipment if you believe it is dama ed in any way.

-NEVER operate the Tube Roller Mixer if the mains power supply is dama ed in any way

-NEVER use any sharp or metal objects near the Tube Roller Mixer control panel

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 8 of 16

Preparation & Installation

The Tube Roller Mixer should be installed and operated in strict accordance with the followin instructions.

CAUTION

Be careful when liftin and observe your local operational health and safety requirements for liftin before unpackin the carton.

Unpacking and Installing

-Carefully remove all packa in material from the Tube Roller Mixer, as well as the User Manual and any other supplied

accessories.

-Carefully inspect the Tube Roller Mixer, mains power supply and all packa in for any si ns of dama e. If any si ns of

dama e are present, do not install or operate the equipment. Contact the supplier of your equipment if you have a received

a dama ed product.

-Place the Tube Roller Mixer in an upri ht position as per Fi ure 1 on a stron , even, flat, smooth surface.

-Ensure that there is a minimum unobstructed distance of 100 millimetres between the left, ri ht and rear panels of the

Tube Roller Mixer and any other object or wall.

-Ensure that there is a suitable mains power supply outlet within reach of the supplied mains power supply without placin

any strain whatsoever on the lead or plu . The Tube Roller Mixer should not be plu ed into any double-adapter, power

board, or power point splitter of any kind but instead directly into a wall mounted power socket.

-Ensure that there is a minimum unobstructed distance of 500 millimetres in front of the Tube Roller Mixer to allow

adequate room for the user to maintain a safe operatin distance of 300 millimetres.

CAUTION

The Tube Rollers Mixer is desi ned for the purpose of a itatin vessels containin liquids.

The contents of these vessels is the sole responsibility of the user or operator, and the use of corrosive, flammable,

combustible, hazardous, environmentally unsafe or otherwise dan erous materials within the container is done so at the risk

and liability of the user or operator.

ALWAYS be 100% sure of the contents of your containers, the expected behavior once a itated and the applicable safety

measures that should be employed when handlin such substances.

ALWAYS ensure your containers are firmly sealed and there is no chance of the sample leakin onto the Tube Roller Mixer or

comin into contact with the Operator.

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 9 of 16

Using The Tube Roller Mixer

Choosing a Suitable Vessel

-The Tube Roller Mixer should only be used with vessels that are sealed with an appropriate cap to prevent spilla e whilst in

use.

Connecting Power

CAUTION

A sur e protected power outlet is stron ly recommended as it provides some protection for the equipment in areas of poor

electrical quality as well as providin some protection a ainst li htnin strikes. The equipment should be operated on a ood,

reliable supply of power at all times.

Note: The Tube Roller Mixer should not be operated on the same electrical circuit as other hi h volta e household appliances

such as frid es, clothes dryers, washin machines or other continuous operation hi h volta e devices. These types of devices

can create power fluctuations that are undesirable for electrically sensitive equipment. Consult your workplace administrator or

electrical maintenance staff if you are unsure.

IMPORTANT: Use of an incorrect power supply will void the product warranty and waive all anufacturer liability for

any and all da age caused by such use. If you are unsure about the rating of your power supply, consult your

workplace ad inistrator or electrical aintenance staff to deter ine if your power supply is suitable for use with this

product before connecting the power supply.

CAUTION

Re ularly check the mains power supply condition over the life of the product, and do not operate the equipment if you suspect

there is dama e to any part of the equipment or the mains power supply.

-Insert the plu end of the mains power supply lead firmly into a properly rated, wall mounted power supply outlet.

-Insert the lead end of the power supply into the socket on the rear of the mixer.

If there are double-adapters or oversized DC power packs causin obstruction of the mains power supply plu , these should

first be removed.

-Ensurin your hands are dry, switch on the power on the mains power supply outlet.

Adjusting The Mixing Control

The Tube Roller Mixer features adjustable mixin speed control to deliver entle a itation throu h to vi orous mixin .

To change the ixing speed

-Slowly turn the speed control knob (element 2 in Fi ure 1) clockwise to increase the speed, or anti-clockwise to decrease

the speed.

-The speed may be adjusted durin mixin to achieve the desired level of mixin inside the vessel.

Ratek BTR5-12V / BTR10-12V Tube Roller Mixer – User Manual

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Page 10 of 16

Operating the Tube Roller Mixer

CAUTION

When workin with lass tubes, flasks, bottles, breakable or other brittle or fra ile articles it is important to wear appropriate

safety eyewear and protective loves to ensure operator safety. In addition, the Tube Roller Mixer should be used in

accordance with your operational health and safety policies.

-Load your tubes or bottles onto the rollers

-Ensure that there are no obstructions which would prevent proper rotation of the samples.

-Switch on the power.

-Select the desired a itation speed. Refer to the section in this User Manual titled “Adjustin The Mixin Control” for

instructions.

-The speed may be adjusted as desired.

-Once desired mixin has been achieved turn the speed dial anti-clockwise to slow the rollers.

-Remove the tubes or bottles once mixin is complete.

-If the mixer is no lon er bein used, switch the power to Off (element 1 in Fi ure 1)

Storing & Relocating The Tube Roller Mixer

The Tube Roller Mixer should be stored out of direct sunli ht at an ambient temperature below 30° Celsius in a clean and dry

location which meets the environmental conditions required as detailed in the technical specifications of this User Manual.

-Switch the power to “Off” (element 1 in Fi ure 1)

-Unplu the equipment from the mains power supply outlet.

-Ensure the Tube Roller Mixer is clean and dry. If required, clean it accordin to the section of this User Manual titled

“Routine Cleanin & Maintenance”.

-Relocate it to an appropriate stora e location. Ensure the Tube Roller Mixer is stored in a clean and dry location away from

potential dama e by accidental knocks and bumps.

Ratek BTR5-12V Bedienungsanleitung

Beliebte Mischer Handbücher anderer Marken