Raven AccuBoom Bedienungsanleitung
Miller Condor G-Series
AccuBoom™ Installation Manual
While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be held responsible or liable for the effects of
atmospheric conditions and sunspot activity on the performance of our products.
Raven Industries cannot guarantee the accuracy, integrity, continuity, or
availability of the GPS signal from the U.S. Department of Defense/NAVSTAR
GPS satellites, the OmniSTAR correction service or the WAAS correction
service.
Raven Industries accepts no responsibility for the use of the signal for other than
the stated purpose. Raven Industries shall not be responsible or liable for
incidental or consequential damages or a loss of anticipated benefits or profits,
work stoppage or loss or impairment of data arising out of the use, or inability to
use, the SmarTrax or any of its components.
Disclaimer
Table of Contents
Manual No. 016-1001-076 i
Chapter 1 Important Safety Information................................................. 1
Important Safety Information ..................................................................................................... 1
Chapter 2 Introduction............................................................................. 3
Introduction ............................................................................................................................... 3
Recommendations .............................................................................................................. 4
Tools Needed ...................................................................................................................... 4
Preparing for Installation ..................................................................................................... 4
Point of Reference ............................................................................................................... 4
AccuBoom Kit Contents ............................................................................................................ 5
Chapter 3 AccuBoom Installation........................................................... 7
Install the AccuBoom Node .......................................................................................................7
Install the AccuBoom Harness Cable ........................................................................................ 8
Chapter 4 Section Mapping Setup ........................................................ 11
Envizio Pro .............................................................................................................................. 11
Viper Pro ................................................................................................................................. 11
Chapter 5 Troubleshooting ................................................................... 13
Table of Contents
ii Miller Condor G-Series AccuBoom Installation Manual
CHAPTER
1
Manual No. 016-1001-076 1
C hapt er 1
Important Safety
Information
Important Safety Information
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the AccuBoom™ system.
•Follow all safety information presented within this manual.
•If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.
•Follow all safety labels affixed to the AccuBoom system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.
When operating the machine after installing AccuBoom, observe the following safety measures:
•Be alert and aware of surroundings.
•Do not operate AccuBoom or any agricultural equipment while under the influence of alcohol or an illegal
substance.
•Remain in the operator’s position in the machine at all times when AccuBoom is enabled.
•Disable AccuBoom when exiting from the operator’s seat and machine.
•Do not drive the machine with AccuBoom enabled on any public road.
•Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling AccuBoom when the safe working distance has been diminished.
•Ensure AccuBoom is disabled prior to starting any maintenance work on AccuBoom or the machine.
•Always verify that the power leads are connected to the correct polarity as marked. Reversing the power
leads could cause severe damage to the equipment.
•Ensure that the power cable is the last cable to be connected.
NOTICE
CAUTION
Chapter 1
2 Miller Condor G-Series AccuBoom Installation Manual
CHAPTER
2
Manual No. 016-1001-076 3
C hapt er 2
Introduction
Introduction
Congratulations on your purchase of the Raven AccuBoom system! This system is designed to provide
accurate and cost-efficient application control by avoiding no-spray zones and eliminating wasteful overlaps.
This manual applies to the following machines. For future reference, write your serial number in the space
below.
MAKE: Miller
MODEL: Condor G-Series
YEAR:
SERIAL NUMBER:
FIGURE 1. Miller Condor G-Series
Chapter 2
4 Miller Condor G-Series AccuBoom Installation Manual
Recommendations
Raven Industries recommends the following best practices when installing the AccuBoom system.
•Use part numbers to identify the parts.
•Do not remove the plastic wrap from a part until it is necessary for installation.
Tools Needed
The following tools are recommended for installation of the AccuBoom system:
•SAE standard-sized wrenches
•Cable ties
•Set of tools
Preparing for Installation
Before installing AccuBoom, park the machine where the ground is level, clean, and dry. Leave the machine
turned off for the duration of the installation process.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
Point of Reference
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
2
Manual No. 016-1001-076 5
Introduction
AccuBoom Kit Contents
This section contains a list of the components that are included in the AccuBoom kit. Before beginning the
AccuBoom installation, compare the items in the AccuBoom kit with the components on this list. If you have
questions about the kit, contact your local Raven dealer.
TABLE 1. AccuBoom Installation Kit (P/N 117-1001-076)
Picture Item Description Part Number Qty.
Not Pictured Manual - Miller Condor G-Series AccuBoom
Installation 016-1001-076 1
Node - CAN AccuBoom 063-0172-316 1
Cable - Miller Condor G-Series CAN
AccuBoom 115-1001-042 1
Bolt - 1/4”-20 x 1” Hex 311-0050-105 3
Nut - 1/4”-20 Nylon Lock 312-4000-057 3
Washer - 1/4” Flat 313-2300-009 6
Chapter 2
6 Miller Condor G-Series AccuBoom Installation Manual
Andere Handbücher für AccuBoom
15
Inhaltsverzeichnis
Andere Raven Steuerungssystem Handbücher
Raven
Raven SCS 340 Handbuch
Raven
Raven RCM-Sprayer Hawkeye 2 Bedienungsanleitung
Raven
Raven SCS 360 Beilage
Raven
Raven Viper Pro Bedienungsanleitung
Raven
Raven AutoBoom Bedienungsanleitung
Raven
Raven AutoBoom Bedienungsanleitung
Raven
Raven AccuBoom Bedienungsanleitung
Raven
Raven AccuBoom Bedienungsanleitung
Raven
Raven RCM-Sprayer Hawkeye 2 Bedienungsanleitung
Raven
Raven RS1 Gebrauchs- und Pflegehandbuch
Raven
Raven AccuBoom Bedienungsanleitung
Raven
Raven SCS-330 Beilage
Raven
Raven RS1/HDU Bedienungsanleitung
Raven
Raven CR Series Bedienungsanleitung
Raven
Raven SmarTrax Bedienungsanleitung
Raven
Raven DCS 300 Handbuch
Raven
Raven RCM Gebrauchs- und Pflegehandbuch
Raven
Raven SBGUIDANCE SMARTRAX MD Bedienungsanleitung
Raven
Raven SCS 440 Bedienungsanleitung
Raven
Raven PRECISION AUTOBOOM G1 Bedienungsanleitung
