Raw Thrills PAC-MAN TICKET MANIA Referenzhandbuch

SERVICE BULLETIN

IMPORTANCE: HIGH

PAC-MAN TICKET MANIA™– FOAM WASHER KIT

(Serial #: RT02400E01-RT02400E99, RT02401E00-RT02401E99, RT02402E00-RT02402E50)

Raw Thrills has identified an aesthetic issue associated with the Pac-Man Ticket Mania™

42” Game. As a result, Raw Thrills is issuing a kit to fix the control panel illumination

problems on games with serial numbers in the ranges listed above. Under normal

conditions, it is likely for there to be unintended illumination underneath the control

panel plastic. The foam washers included in this kit sent with this bulletin must be

installed as shown in the instructions below.

Figure A - Pre-Kit Illumination Figure B - Post-Kit Illumination

For Additional Assistance, Please Contact Joe Blackwell of Namco at 847-264-5614.

Kit Description:

(9) ADHESIVE-BACKED FOAM WASHERS

(1) INSTALLATION INSTRUCTION SHEET

Required Tools:

(1) DRILL OR 1/4" SCREWDRIVER WITH T-27 TAMPERPROOF TORX & PHILLIPS BIT

(1) 3/8” SOCKET WRENCH

(1) PAIR OF GLOVES (FOR HANDLING OF CLEAR CONTROL PANEL PLASTIC)

PROCEDURE:

1. REMOVE START BUTTON AND JOYSTICK PLATE ASSEMBLY

•OPEN COIN DOOR, AND LOCATE THE HARNESS FOR THE START BUTTON

AND JOYSTICK AND TRACE IT BACK TO THE CONNECTOR WHICH LEADS

TO THE I/O BOARD. UNPLUG THIS CONNECTION, WHICH CAN MOST

EASILY BE DONE FROM THE LOWER BACK DOOR (PHILLIPS BIT

SCREWDRIVER MAY BE NEEDED IF SHIPPING SCREWS ARE STILL

INSTALLED ON DOOR). AFTER UNPLUGGING THE CONNECTION, REMOVE

THE START BUTTON AND JOYSTICK SIDE OF THE HARNESS FROM ANY

WIRE CLAMPS SO THAT IT CAN BE REMOVED FROM THE GAME EASILY.

Figure C - Control Panel Harness to I/O Connector Figure D – Unplugged Connection

•CAREFULLY TWIST THE LIGHT/SWITCH ON THE BOTTOM SIDE OF THE

START BUTTON AND REMOVE. USING 3/8” SOCKET, REMOVE (4) 10-32

LOCKNUTS AND WASHERS SECURING THE JOYSTICK PLATE ASSEMBLY

TO THE CONTROL PANEL; LOCKNUTS ARE LOCATED AT THE FRONT,

RIGHT, BACK AND LEFT EDGES OF THE JOYSTICK PLATE. TAKE NOTE

OF THE LOCATION OF THE GREEN OR SILVER GROUNDING WIRE WHICH

WILL BE AFFIXED TO THE JOYSTICK PLATE; IT WILL NEED TO BE

REATTACHED WHEN REINSTALLING THE JOYSTICK PLATE ASSEMBLY.

REMOVE JOYSTICK PLATE ASSEMBLY WITH HARNESS ATTACHED.

Figure E - Joystick Plate and Start Button Mounting Figure F - Joystick Plate Assembly Removed

•LOOSEN AND REMOVE THE RETAINING NUT ON THE BUTTON AND

REMOVE THE START BUTTON.

•USING T-27 TAMPERPROOF TORX BIT, REMOVE (5) SCREWS AND

ACCOMPANYING WASHERS TO FREE THE CLEAR CONTROL PANEL

PLASTIC. BECAUSE OF THE LED LIGHT STRIP THAT IS INSERTED INTO

THIS PLASTIC PART, CARE SHOULD BE TAKEN WHEN EITHER REMOVING

THE PLASTIC PART OR WHEN PROPPING IT UP AGAINST THE GLASS.

(NOTE: CONTROL PANEL PLASTIC IS HIGHLY SENSITIVE TO

FINGERPRINTS AND SCRATCHES. TAKE EXTREME CARE WHEN

HANDLING THIS PART; GLOVES ARE RECOMMENDED.)

Connectors

Wire Clamp

Joystick

Plate

Mounts (4)

Start

Button

Retaining

Nut

Ground

Ring

Terminal

Figure G - Clear Control Panel Plastic, Shown Propped Up Against Glass

2. INSTALL ADHESIVE-BACKED FOAM WASHERS ON DECALLED CONTROL PANEL

•INSTALL (9) ADHESIVE-BACKED FOAM WASHERS ATOP THE DECAL ON

THE CONTROL PANEL OF THE CABINET. (5) WILL BE INSTALLED AT THE

OUTER HOLE LOCATIONS OF THE CONTROL PANEL PLASTIC HOLE

MOUNTS AND (4) WILL BE INSTALLED AT THE JOYSTICK PLATE

THROUGH HOLES ON THE CONTROL PANEL. (NOTE: ADHESIVE ON BACK

OF FOAM WASHERS IS PERMANENT. CARE MUST BE TAKEN WHEN

INSTALLING THESE AS THE ADHESIVE WILL STICK TO DECAL

IMMEDIATELY AND REALIGNMENT WILL NOT BE POSSIBLE.)

Figure H - Install Foam Washers Centered on (9) Control Panel Holes

Reference

Figure G

above for

precise hole

locations.

Foam

washer hole

locations.

Foam

washer hole

locations.

3. REASSEMBLE THE CONTROL PANEL

•IF NECESSARY, CLEAN THE CONTROL PANEL PLASTIC WITH A NON-

ABRASIVE CLEANING AGENT AND NON-ABRESIVE TOWEL (NOTE:

PLASTIC CAN SCRATCH). ALSO, CLEAN OFF ANY DUST THAT MAY BE ON

THE DECALLED SURFACE OF THE CONTROL PANEL.

•REINSTALL THE CLEAR CONTROL PANEL PLASTIC IN THE SAME

FASHION IT WAS INSTALLED BEFORE. MAKE SURE THAT THE LED LIGHT

STRIP IS PROPERLY INSERTED INTO THE CHANNEL NEAR THE BACK OF

THE PLASTIC WHEN IT IS BEING REALIGNED AND INSTALLED. USING T-

27 TAMPERPROOF TORX BIT, INSTALL THE (5) SCREWS THAT AFFIX THE

CONTROL PANEL PLASTIC TO THE CABINET.

•REINSTALL THE START BUTTON, WITH ITS ACCOMPANYING RETAINING

NUT; THERE ARE REGISTRATION TABS ON THE UNDERSIDE OF THE

BUTTON TO MATCH THE NOTCHES ON THE CONTROL PANEL PLASTIC.

•REINSTALL THE JOYSTICK PLATE ASSEMBLY USING A 3/8” SOCKET

WRENCH AND THE (4) WASHERS AND LOCKNUTS. THE GROUND WIRE

(GREEN OR SILVER) RING TERMINAL MUST ALSO BE REINSTALLED IN

THIS STEP. THE ORIENTATION OF THE JOYSTICK PLATE SHOULD BE

SUCH THAT THE PART NUMBER ON JOYSTICK PLATE DECAL IS

LOCATED IN THE BOTTOM RIGHT, OR 4:30 IN CLOCK LINGO.

Figure I - Decal Part Number (Bottom Right) used for Orientation

•REATTACH THE LIGHT/SWITCH OF THE HARNESS TO THE START

BUTTON. RECONNECT THE HARNESS AT THE I/O CONNECTION THAT

WAS PREVIOUSLY DISCONNECTED. PLACE HARNESS BACK INTO WIRE

CLAMP AS WAS PREVIOUSLY DONE.

4. CHECK SWITCHES IN TEST MENU

•USING THE SERVICE BRACKET INSIDE THE COIN DOOR, ENTER THE

TEST MENU, SELECT DIAGNOSTIC MENU, THEN SELECT SWITCH TEST

TO VERIFY THAT THE START BUTTON AND JOYSTICK SWITCHES ARE

FUNCTIONAL AND CORRECT. MAKE ADJUSTMENTS IF NECESSARY.

Inhaltsverzeichnis

Andere Raw Thrills Arcade-Spielautomat Handbücher

Raw Thrills

Raw Thrills Jurassic Park Arcade Bedienungsanleitung

Raw Thrills

Raw Thrills Terminator Salvation Bedienungsanleitung

Raw Thrills

Raw Thrills Halo: Fireteam Raven Super Deluxe Bedienungsanleitung

Raw Thrills

Raw Thrills King Kong of Skull Island Bedienungsanleitung

Raw Thrills

Raw Thrills Fast and Furious Arcade Bedienungsanleitung

Raw Thrills

Raw Thrills Injustice Arcade Bedienungsanleitung

Raw Thrills

Raw Thrills Space Invaders Frenzy Bedienungsanleitung

Raw Thrills

Raw Thrills Super Bikes 3 Bedienungsanleitung

Raw Thrills

Raw Thrills Bust-a-Move Frenzy Bedienungsanleitung

Raw Thrills

Raw Thrills King Kong of Skull Island II Bedienungsanleitung

Raw Thrills

Raw Thrills Teenage Mutant Ninja Turtles Bedienungsanleitung

Beliebte Arcade-Spielautomat Handbücher anderer Marken

Universal Space

Universal Space COCONUT BASH Bedienungsanleitung

Bay-Tek

Bay-Tek EVOLVE Bedienungsanleitung

Global VR

Global VR America's Army Montage- und Bedienungsanleitung

Atronic

Atronic Cashline Bedienungsanleitung

Universal Space

Universal Space Checky Monkey Bedienungsanleitung

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Bedienungsanleitung

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Bedienungsanleitung

Family Fun Companies

Family Fun Companies Reactor Kurzanleitung

Universal Space

Universal Space FRUIT MANIA Extreme Bedienungsanleitung

falgas

falgas CARRUSEL FIESTA Bedienungsanleitung

Konami

Konami DanceDanceRevolution Bedienungsanleitung

Bay-Tek

Bay-Tek quik drop Bedienungsanleitung

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Bedienungsanleitung

Adrenaline

Adrenaline Flying Tickets Montage- und Bedienungsanleitung

Swinks

Swinks Stern Pinball Ghostbusters Bedienungsanleitung

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Bedienungsanleitung

jakar

jakar SPEED CARS Bedienungsanleitung

Carmelli

Carmelli HAT TRICK NG1015H Bedienungsanleitung