Raymar DSP9612RM Bedienungsanleitung

DSP9612RM USER’S GUIDE

0049-0519-000 Page i REV.D

DSP9612RM Flash Poll

Rack-Mount Modem

User’s Guide

DSP9612RM USER’S GUIDE

0049-0519-000 Page ii REV.D

The products and programs described in this User’s Guide are licensed products

of Raymar Information Technology, Inc. This User’s Guide contains proprietary

information protected by copyright, and this User’s Guide and all accompanying

hardware and documentation are copyrighted.

Raymar Information Technology, Inc. does not warrant that the hardware will

work properly in all environments and applications, and makes no warranty and

representation, either implied or expressed, with respect to the quality,

performance, merchantability, or fitness for a particular purpose.

Information in this User’s Guide is subject to change without notice and does not

represent a commitment on the part of Raymar Information Technology, Inc.

Raymar Information Technology, Inc. assumes no responsibility for any

inaccuracies that may be contained in this User’s Guide.

Raymar Information Technology, Inc. makes no commitment to update or keep

current the information in this User’s Guide, and reserves the right to make

changes to this User’s Guide and/or product without notice.

No part of this manual may be reproduced or transmitted in any form or by any

means, electronic or mechanical, including photocopying, recording, or

information storage and retrieval systems, for any purpose other than the

purchaser's personal use, without the express written permission of Raymar

Information Technology, Inc.

Raymar Information Technology, Inc.

7325 Roseville Road

Sacramento, California 95842

Tel: 800-695-1951

Direct: (916) 783-1951

Fax: (916) 783-1952

DSP9612RM USER’S GUIDE

0049-0519-000 Page iii REV.D

Compliances

This device complies with Part 15A of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15A of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit other than the one to which

the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

If none of these actions resolves the problem, consult your distributor or an

experienced radio/television technician for additional suggestions.

Additionally, Section 15.838, paragraph d), of the FCC Rules and Regulations

states: “Where special accessories, such as shielded cables, are required in order

to meet FCC regulations, shielded cables must be used with this equipment.

Operation with non-approved equipment or unshielded cables is likely to result in

interference to radio and TV reception. The user is cautioned that changes and

modifications to this equipment without the approval of the manufacturer could

void the user’s authority to operate this equipment.

DSP9612RM USER’S GUIDE

0049-0519-000 Page iv REV.D

Contents

CHAPTER 1 INTRODUCTION......................................1

FEATURES.............................................................................2

APPLICATIONS ......................................................................2

ANCILLARY DOCUMENTATION..............................................3

CHAPTER 2 INSTALLATION .......................................4

UNPACKING YOUR HARDWARE ............................................4

ADDITIONAL ITEMS YOU NEED.............................................4

HARDWARE OVERVIEW ........................................................4

Front View........................................................................4

Component View...............................................................5

INSTALLATION SUMMARY.....................................................7

CONFIGURING THE MODEM...................................................7

SW1 DIP Switch Settings..................................................8

SW2 DIP Switch Settings................................................11

SW3 DIP Switch Settings................................................14

INSTALLING THE MODEM....................................................18

CONNECTING TO A TRANSMISSION LINE .............................19

Modular Jack Connectors ..............................................19

Mass Termination Connector.........................................20

CONNECTING AN RS-232 DEVICE.......................................20

LEDS..................................................................................21

LOOPBACK CONTROL SWITCH ............................................21

APPENDIX A TROUBLESHOOTING.........................27

PROBLEM SOLVING.............................................................27

APPENDIX B SPECIFICATIONS................................24

GENERAL SPECIFICATIONS..................................................24

MECHANICAL SPECIFICATIONS ...........................................25

BACK-TO-BACK CONNECTIONS TO A SECOND MODEM.......26

RS-232 (RTU) Interface..................................................26

ENVIRONMENTAL SPECIFICATIONS .....................................27

APPENDIX C LIMITED PRODUCT WARRANTY...28

APPENDIX D RMA PROCEDURE..............................29

DSP9612RM USER’S GUIDE

0049-0519-000 Page 1 REV.D

Chapter 1

Introduction

Congratulations for purchasing the finest industrial-grade fast-poll rack-mount

modem available.

The Raymar-Telenetics DSP9612RM (Flash Poll) modem is a 9600/4800/0-1800

bps rack-mount modem designed for 4-wire, full-duplex or 2-wire, half-duplex

operation over a voice-band leased line. The modem is designed utilizing the

latest digital-signal processing (DSP) technology to achieve high performance.

The modem employs Raymar-Telenetics’ proprietary modulation and encoding

scheme to achieve fast modem training time. It is also backward compatible with

Bell 202 modems.

The modem can be installed in an RM16M Rack (16 slots, 3U) or the RMX Shelf

(2 slots, 1U) from Raymar-Telenetics. The modem occupies only one rack slot,

eliminating the hassle of equipment trays and power bricks required for “Stand

Alone” modems. The modem is powered from the modem rack.

The DSP9612RM modem is ideally suited for multi-point communication

systems that require fast response time, short training time, and low throughput

delay. The modem is the most technologically advanced rack-mount modem on

the market.

This User’s Guide is designed to let you get your modem “up and running” as

quickly as possible. It contains all the information you need to install and

configure your modem. It also contains troubleshooting information in the

unlikely event you encounter a problem with your modem.

DSP9612RM USER’S GUIDE

0049-0519-000 Page 2 REV.D

Features

Though functionally similar to commercial modems, the DSP9612RM provides

the following unique features that make it well suited for utility and industrial

applications.

Requires only one rack slot.

Operates over voice-band conditioned or unconditioned leased line and

pilot wires.

Operates without human intervention, making it ideal for unmanned

locations.

Works within an extended temperature range of -40ºC to +85ºC.

Designed with coupling transformers for high-voltage isolation and

common mode noise rejection in industrial and commercial environments.

Asynchronous data rates (selectable) of 9600, 4800, and 0-1800 bps.

Easily accessible DIP switches for user configuration and option selection.

Local analog, local digital, and remote digital loopback diagnostics.

Applications

The DSP9612RM modem is designed for point-to-point and multipoint data

communications. Figure 1-1 shows a typical multipoint configuration.

Figure 1-1. Network of Multipoint Configuration

DSP9612RM USER’S GUIDE

0049-0519-000 Page 3 REV.D

There are a number of factors that can affect the network’s and modem’s

operation and performance. These include:

Operating speed

2-wire or 4-wire configuration

Transmission line characteristics, noise, and line impairments

Network configuration (point-to-point or multipoint)

Number of nodes on the network

Ancillary Documentation

For information about how to adapt an AC powered DSP9612RM modem to a

DC power operation, refer to the included documents (0062-0117-001). Also

refer to the RM16M Installation and Operation Guide (TEL-6200508506004).

DSP9612RM USER’S GUIDE

0049-0519-000 Page 4 REV.D

Chapter 2

Installation

This chapter describes how to install the modem.

Unpacking Your Hardware

Your package should include:

At least one DSP9612RM modem

This User’s Guide (on CD)

If your package contents are damaged or missing, please contact your place of

purchase immediately.

Additional Items You Need

To use your modem, you need the following additional items:

An RM16M Rack or an RMX Shelf from Raymar-Telenetics

A two- or four-wire transmission line or leased line

Hardware Overview

Front View

Figure 2-1 shows a front view of the DSP9612RM modem. Starting from the top,

this view shows:

A loopback test switch. See page 21.

A set of eight LEDs. See page 21.

DSP9612RM USER’S GUIDE

0049-0519-000 Page 5 REV.D

Figure 2-1. Front View of Modem

Component View

Figure 2-2 shows the component view of the modem. This view shows:

Three configuration switch blocks, designated SW1, SW2, and SW3. See

page 7.

Jumpers located in various positions on the modem. Do not change or

remove the straps from these jumpers.

Edge connectors at the back of the modem, which plug into the backplane

of an RMX Shelf or an RM16M Rack from Raymar-Telenetics.

DSP9612RM USER’S GUIDE

0049-0519-000 Page 6 REV.D

Figure 2-2. Component View of Modem

Edge Connectors Configuration

Switch Blocks

Switch Block

SW2 Switch Block SW1

Switch Block SW3

Inhaltsverzeichnis

Andere Raymar Modem Handbücher

Raymar

Raymar HIDEX Bedienungsanleitung

Raymar

Raymar BBI-14.4 Betriebsanleitung

Raymar

Raymar Myriad MD202T Bedienungsanleitung

Raymar

Raymar Telenetics MIU14.4L Bedienungsanleitung

Raymar

Raymar V.32M/14.4 Bedienungsanleitung

Raymar

Raymar MIU202T Bedienungsanleitung

Raymar

Raymar MOT202TSA Bedienungsanleitung

Raymar

Raymar RMX-2 Betriebsanleitung

Raymar

Raymar ASTRO 25 Analog Modem II Bedienungsanleitung

Raymar

Raymar DSP9612 Bedienungsanleitung

Raymar

Raymar 2.4 MIU/PowerPort Series Bedienungsanleitung

Raymar

Raymar Alliance V.34M Bedienungsanleitung

Raymar

Raymar 326X V.34 Series Bedienungsanleitung

Raymar

Raymar Telenetics MIU9.6FPD Bedienungsanleitung

Raymar

Raymar Myriad MD9612FP Bedienungsanleitung

Raymar

Raymar 3460 Bedienungsanleitung

Raymar

Raymar Hidex HXII Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung