Raynor Ultra II 8587RGD Bedienungsanleitung

CONTENTS

Preparation . . . . . . . . . . . . . . . .2-3

Assembly . . . . . . . . . . . . . . . . .4-5

Installation . . . . . . . . . . . . . . . 6-13

Install the Door Control. . . . . . 14-16

Install the Protector System®. . 17-20

Power. . . . . . . . . . . . . . . . . . 21-22

Adjustments . . . . . . . . . . . . . 23-25

Operation . . . . . . . . . . . . . . . . . 26

Features . . . . . . . . . . . . . . . . . . 27

Door Control . . . . . . . . . . . . . 28-29

Remote Control . . . . . . . . . . . 30-31

To Erase the Memory . . . . . . . . . 31

To Open the Door Manually . . . . . 32

Maintenance . . . . . . . . . . . . . . . 32

Troubleshooting. . . . . . . . . . . 33-34

Accessories. . . . . . . . . . . . . . . . 35

Warranty. . . . . . . . . . . . . . . . . . 36

Repair Parts . . . . . . . . . . . . . 37-38

Notes . . . . . . . . . . . . . . . . . . . . 39

PREMIUM Series

Chain Drive Garage

Door Opener

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■The door WILL NOT CLOSE unless the Protector System®is connected and properly

aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■The model number label is located on the front panel of your garage door opener.

■This garage door opener is ONLY compatible with MyQ®and Security+ 2.0™

accessories.

■ONLY enable the Timer-to-Close* or MyQ®remote operation feature* when

the garage door opener is installed on a sectional door. (*Not available on all

models)

NOTE: If you are installing the garage door opener on a one-piece door, visit

www.raynor.com for installation instructions.

Serial Number:

Date of Purchase:

Model 8587RGD - 3/4 hp

FOR RESIDENTIAL USE ONLY

Write down the following information for

future reference:

Raynor Garage Doors

1101 E. River Rd.

Dixon, Illinois 61021

www.raynor.com

Safety Symbol and Signal

Word Review

Thisgarage door opener has been designed and

tested to offer safe service provided it isinstalled,

operated,maintained and tested in strict

accordance with the instructions and warnings

contained in this manual.

When you see these Safety Symbolsand Signal

Words on the following pages, they will alert you

to the possibilityof serious injury or death if you

do notcomply with the warnings that accompany

them. The hazard maycome from something

mechanical or from electric shock. Read the

warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following

pages, it will alert you to the possibilityof damage

to your garage door and/or the garage door

opener if you do notcomply with the cautionary

statements that accompany it. Read them

carefully.

Check the Door

1. Disable locks and remove any ropes

connected to the garage door.

2. Lift the door halfway up. Release the

door. If balanced, it should stay in

place, supported entirely by its springs.

3. Raise and lower the door to check for

binding or sticking. Ifyour door binds,

sticks, or is out of balance, call a trained

door systems technician.

4. Check the seal on the bottom of the

door.Any gap between the floor and

the bottom of the door must not exceed

1/4 inch (6 mm). Otherwise, the safety

reversal system may not work properly.

5. The opener should be installed above

the center of the door. If there is a

torsion spring or center bearing plate

in the way ofthe header bracket,it may

be installed within 4 feet (1.2 m) to the

left or right of the door center. See

page 7.

Torsion Spring Extension Spring

To prevent possible SERIOUSINJURYor

DEATH:

• ALWAYS call a trained door systems

technician if garage door binds, sticks, or

isout ofbalance.An unbalanced garage

door may NOT reverse when required.

• NEVER try to loosen,move or adjust

garage door,door springs,cables,

pulleys,brackets or their hardware,

ALLof which are under EXTREME

tension.

• Disable ALLlocks and remove

ALLropesconnected to garage door

BEFORE installation and operating

garage door opener to avoid

entanglement.

To prevent damage to garage door and

opener:

• ALWAYS disable locks BEFORE

installing and operating the opener.

• ONLY operate garage door opener at

120 V,60 Hzto avoid malfunction and

damage.

Tools Needed

3/16

7/16

1/2

5/32

5/16

5/8

9/16

1/4

7/16

Preparation

Overview/Carton Inventory

GARAGE DOOR OPENER ASSEMBLY

A. tekcarbredaeH

B. Pulley and bracket

C. tekcarbrooD

D. mrarooddevruC

E. mraroodthgiartS

F. yellorT

G. Emergency release rope and handle

H. Rail

I. reneporoodegaraG

NOTE: Accessories will vary depending on the garage door opener model purchased. Depending on your specific model, other accessories

may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included

in this manual. The images throughout this manuals are for reference and your product may look different.

J. Chain spreader

K. Chasis support bracket

L. Chain

M. lortnocrooD

N. eriwetihw/derdnaetihW

The Protector System®

O. srosnesgnisreverytefaS

with white and white/black wire attached:

Sending Sensor (1), Receiving Sensor (1)

Safety Sensor Brackets (2), and Extension

Brackets (2)

P. erutaretildnaslebalytefaS

Q. Rail grease

Hardware

Assembly

Washered Bolts and Lock Washer

[mounted in the top of the garage door opener]

Screw #8-32 x 3/8" (2)

Hex Bolts 1/4"-20 x 5/8" (2)

Lock Washers (2)

Washered Bolt 5/16"-18 x 1/2" (2)

Chassis Support Bracket Hardware

Screw #8-32 x 3/8" (2)

Chain Spreader Hardware

Rail Hardware

Installation

Hex Bolt 5/16"-18 x 7/8" (4)

Lag Screw 5/16"-9 x 1-5/8" (2)

Lag Screw 5/16"-18 x 1-5/8" (2)

Clevis Pin 5/16" x 2-3/4" (1)

Clevis Pin 5/16" x 1-1/4" (1)

Clevis Pin 5/16" x 1" (1)

Nut 5/16"-18 (4)

Lock Washer 5/16"-16 (4)

Self-Threading Screw 1/4"-14 x 5/8" (2)

Ring Fastener (3)

Carriage Bolt 1/4"-20 x 1/2" (2)

Wing Nut 1/4"-20 (2)

Hex Bolt 1/4"-20 x 5/8" (2)

Lock Nut 1/4"-20 (2)

Lag Screw 1/4" x 1-1/2" (4)

Door Control Hardware

Screw 6AB x 1-1/4" (2)

Screw 6-32 x 1" (2)

Drywall Anchors (2)

Insulated Staples

893RGX

Remote

Control

041A7305-3

Smart Control

Panel®

MyQ®AND SECURITY✚TM

2.0 ACCESSORIES

Preparation

To avoid SERIOUS damage to garage door

opener, use ONLY those bolts/fasteners

mounted in the top of the opener.

Washered Bolt

5/16"-18x1/2"

(Mounted in the

garage door opener)

HARDWARE

Lock Nut

(Mounted in the

garage door opener)

NOTE: ONLY use the bolts removed from the

garage door opener.Place the garage door

opener on the packing material to prevent

scratching.

1.1 Remove bolt and lock nut from the top

ofthe garage door opener.

1.2 Align the rail and the styrofoamover the

sprocket.Cut the tape from the rail,

chain, and styrofoam.

1.3 Fasten the rail with the previously

removed washered bolt and locknut.

1.4 Position the chain around the garage

door opener sprocket.

1.5 Attach the chain spreader to the garage

door opener with screws.

1.6 Guide the chain around the selected

groove in the chain spreader, to

engage either the 8-tooth or 6-tooth

sprocket.

NOTE:The 6-tooth sprocket is for use

with Carriage House Doors and the 8-

tooth sprocket is for use with regular

doors.

Lock

Nut

Washered Bolt

5/16"-18x1/2"

Hex Screws 8-32x1"

Washers

Chain Spreader6-Tooth

Sprocket

8-Tooth

Sprocket

Chain Spreader

Motor Unit Mounting Plate Motor Unit Mounting Plate

Assembly

1Attach the rail to the garage door opener

2 Attach the Chassis Support Bracket

To avoid possible SERIOUS INJURY to finger from moving garagedoor opener:

•ALWAYS keephand clear of sprocket while operating opener.

•Securely attach sprocket cover BEFORE operating.

2.1 Position the chassis support bracket on the unit.

2.2 Attach the bracket to the rail with 1/4"-20x5/8" hex bolts and lock washers. Do not overtighten.

2.3 Attach the bracket to the opener by insertinga5/16"-18x1/2" washered screw throughahole in each side flange andamatching hole in the

bracket. Complete the connection by inserting the #8-32x3/8" screw through the back flangeand the hole in rail support .

Washerd Bolt

5/16

"-18x1/2"

Screw

#8-32x3/8"

Hex Bolt

1/4"-20x5/8"

Lock

Washer

3Tighten the Chain

3.1 Loosen the inner nut and lock washer on the trolley threaded shaft.

3.2 Tighten the outer nutuntil the chain is a 1/2 inch above the base of the rail at the midpoint of

the rail.

3.3 Re-tighten the innernut.

Slack in the chain is normal when the door is closed. No readjustment is necessary.

NOTE: Sprocket noise can result if the chain is too loose. During future maintenance, ALWAYS pull

the emergency release handle to disconnect the trolley before adjusting the chain.

1/2"

Assembly

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.

2. Install garage door opener ONLY on properly balanced and lubricated garage door. An

improperly balanced door may NOT reverse when required and could result in SEVERE

INJURY or DEATH.

3. ALL repairsto cables,spring assemblies and other hardware MUST be made by a trained

door systemstechnician BEFORE installing opener.

4. Disable ALL locksand remove ALL ropes connected to garage door BEFORE installing

opener to avoid entanglement.

5. Install garage door opener 7 feet(2.13 m) or more above floor.

6. Mount the emergency release within reach, but at least6 feet (1.83 m) above the floor and

avoiding contactwith vehicles to avoid accidental release.

7. NEVER connectgarage door opener to power source until instructed to do so.

8. NEVERwear watches, rings or loose clothing while installing or servicing opener.They could

be caughtin garage door or opener mechanisms.

9. Install wall-mounted garage door control:

• within sight ofthe garage door.

• out of reach of children at minimum height of 5 feet (1 5 m).

• away from ALL moving parts of the door.

10. Place entrapment warning label on wall next to garage door control.

11. Place manual release/safety reverse testlabel in plain view on inside ofgarage door.

12. Upon completion of installation, test safety reversal system. Door MUST reverse on contact with

a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat) on the floor.

13. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution,disconnectALL

electric power BEFORE performing ANY service or maintenance.

14. DO NOT enable the Timer-to-Close functionality ifoperating either one-piece or swinging

garage doors. To be enabled ONLY when operating a sectional door.

NOTE:If you are installing the garage door opener on a one-piece door, visit www raynor.com for installation instructions.

Installation

To prevent possible SERIOUS INJURY or

DEATH:

•Header bracket MUST be RIGIDLY

fastened to structural support on header

wall or ceiling, otherwise garage door might

NOT reverse when required. DO NOT

install header bracket over drywall.

•Concrete anchors MUST be used if

mounting header bracket or 2x4 into

masonry.

•NEVER try to loosen, move or adjust

garage door, springs, cables, pulleys,

brackets, or their hardware, ALL of which

are under EXTREME tension.

•ALWAYS call a trained door systems

technician if garage door binds, sticks, or is

out of balance. An unbalanced garage

door might NOT reverse when required.

1Determine the header bracket location

NOTE: If you are installing the garage door opener on a one-piece door, visit www.raynor.com for

installation instructions.

1.1 Close the door and mark the inside vertical centerline of the garage door.

1.2 Extend the line onto the header wall above the door.

You can fasten the header bracket within 4 feet (1.22 m) of the left or right of the door

center only if a torsion spring or center bearing plate is in the way; or you can attach it to

the ceiling when clearance is minimal. (It may be mounted on the wall upside down if

necessary, to gain approximately 1/2" (1 cm).

If you need to install the header bracket on a 2x4 (on wall or ceiling), use lag screws (not

provided) to securely fasten the 2x4 to structural supports.

1.3 Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on

the header wall 2" (5 cm) above the high point. This height will provide travel clearance for the

top edge of the door.

NOTE: If the total number of inches exceeds the height available in your garage, use the maximum

height possible, or refer to page 8 for ceiling installation.

Sectional door with curved track

Header Wall

Track

2" (5 cm)

Highest Point

of Travel

Door

Header Wall

Unfinished

Ceiling

Vertical Centerline

of Garage Door

2x4

Structural

Supports

Level

(Optional)

OPTIONAL

CEILING

MOUNT FOR

HEADER

BRACKET

Installation

You can attach the header bracket either to the

wall above the garage door,or to the ceiling.

Follow the instructions which will work best for

your particular requirements. Do not install the

header bracket over drywall. If installing into

masonry, use concrete anchors (not provided).

HARDWARE

Lag Screw

5/16" - 9 x 1-5/8"

OPTION A WALL INSTALLATION

2.1A Center the bracket on the vertical

centerline with the bottom edge of the

bracket on the horizontal line as shown

(with the arrow pointing toward the

ceiling).

2.2A Mark the vertical set of bracket holes (do

not use the holes designated for ceiling

mount). Drill 3/16" pilot holes and fasten

the bracket securelyto a structural

support with lag screws.

OPTION B CEILING INSTALLATION

2.1B Extend the vertical centerline onto the

ceiling as shown.

2.2B Center the bracket on the vertical mark,

no more than 6" (15 cm) from the wall.

Make sure the arrowis pointing toward

the wall. The bracket can be mounted

flush against the ceiling when clearance

is minimal.

2.3B Mark the side holes. Drill 3/16" pilot holes

and fasten bracketsecurely to a structural

support with lag screws.

Wall Mount

Optional

Mounting

Holes

Vertical

Centerline of

Garage Door

(Header Wall)

Header

Bracket

2x4 Structural

Support

Door Spring

(Garage Door)

Highest Point of

Garage Door

Travel

Horizontal

Line

Lag Screw

5/16" - 9 x 1-5/8"

(Header Wall)

Ceiling Mounting Holes

(Finished Ceiling)

Vertical

Centerline of

Garage Door

Header

Bracket

6" (15 cm)

Maximum

Door Spring

(Garage Door)

Lag Screw

5/16" - 9 x 1-5/8"

Installation

2 Install the Header Bracket

3.1 Align the rail with the header bracket.

Insert the clevis pin through the holes in

the header bracket and rail. Secure

with the ring fastener.

NOTE: Use the packing material as a

protective base for the garage door opener.

Ring

Fastener

Clevis Pin

5/16" X 2-3/4"

HARDWARE

Clevis Pin

5/16" x 2-3/4" Ring Fastener

4Position the garage door opener

To prevent damage to garage door, rest garage

door opener rail on 2x4 placed on top section of

door.

4.1 Remove the packing material and lift the

garage door opener onto a ladder.

NOTE: A 2x4 is ideal for setting the distance

between the rail and the door. If the ladder is

not tall enough you will need help at this point.

4.2 Fully open the door and place a 2x4 (laid flat) under the rail.

NOTE: If the door hits the trolley when it is raised, pull the trolley release arm down to

disconnect the inner and outer trolley. Slide the outer trolley toward the garage door opener.

The trolley can remain disconnected until instructed.

Connected Disconnected

3Attach the rail to the header bracket

Installation

To avoid possible SERIOUS INJURY from a

falling garage door opener, fasten it SECURELY

to structural supportsof the garage. Concrete

anchors MUST be used if installing ANY brackets

into masonry.

HARDWARE

Hex Bolt 5/16"- 18x7/8"

Nut 5/16"-18

Lock Washer

5/16"

Hanging your garage door opener will vary

depending on your garage. Two representative

installations are shown. Yours may be different.

Hanging brackets should be angled (Figure 1) to

provide rigid support. On finished ceilings (Figure

2), attach a sturdy metal bracketto structural

supportsbefore installing the opener. This

bracket and fastening hardware are not provided.

Instructions below are for attaching the garage

door opener directly to structural supports.

5.1 Measure the distance from each side of the

motor unit to the structural support.

5.2 Cut both pieces of the hanging bracket to

required lengths.

5.3 Drill 3/16" pilot holes in the structural

supports.

5.4 Attach one end of each bracket to a

support with 5/16"-18x1-7/8" lag screws

(not provided).

5.5 Fasten the opener to the hanging brackets

with 5/16"-18x7/8" hex bolts, lock washers

and nuts.

5.6 Checkto make sure the rail is centered

over the door (or in line with the header

bracket if the bracket is not centered above

the door).

5.7 Remove the 2x4. Operate the door

manually.If the door hitsthe rail, raise the

header bracket.

NOTE: DO NOT connect power to opener at this

time.

FIGURE 1 FIGURE 2

(Not Provided)

Lag Screws

5/16"- 18x1-7/8"

Measure

Distance

Hex Bolt 5/16"- 18x7/8", Lock Washer 5/16", Nut 5/16"-18

FIGURE 3

Not Provided

Finished Ceiling

Unfinished Ceiling

Installation

5Hang the garage door opener

Inhaltsverzeichnis

Andere Raynor Garagentoröffner Handbücher

Raynor

Raynor COMMANDER 2000RGD Bedienungsanleitung

Raynor

Raynor 8500WRGD Bedienungsanleitung

Raynor

Raynor 3595RGD 3/4 HP Bedienungsanleitung

Raynor

Raynor Premium series 8500RGD Prodigy II Bedienungsanleitung

Raynor

Raynor Sergeant II Standard 8160WRGD Bedienungsanleitung

Raynor

Raynor Prodigy III Bedienungsanleitung

Raynor

Raynor 3255RGD Bedienungsanleitung

Raynor

Raynor 3265RGDM 1/2 HP Bedienungsanleitung

Raynor

Raynor Sergeant II STANDARD Series Bedienungsanleitung

Raynor

Raynor ULTRA SAFETY SIGNAL 2595RGD Bedienungsanleitung

Raynor

Raynor MT5011UCHB Bedienungsanleitung

Raynor

Raynor RapidCoil RC300 Series Bedienungsanleitung

Raynor

Raynor 3280RGDM Bedienungsanleitung

Raynor

Raynor PILOT 2265RGD Bedienungsanleitung

Raynor

Raynor Commander II Safety Signal 3240RGD Bedienungsanleitung

Raynor

Raynor Navigator 1245RGD Bedienungsanleitung

Raynor

Raynor Navigator 2245RGD Bedienungsanleitung

Raynor

Raynor MJ5011UCHB Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor 3265RGDM 1/2 HP Bedienungsanleitung

Raynor

Raynor Safety Signal 3800RGD Bedienungsanleitung

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor ULTRA 3595RGDS 3/4 HP Bedienungsanleitung

Raynor

Raynor 2220RGD 1/2 HP Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung