Raynor MJ5011UCHB Bedienungsanleitung

MEDIUM DUTY DOOR OPERATOR

MODELS MJ5011UCHB, MH5011URCHB, & MH5011ULCHB

INSTALLATION MANUAL

NOT FOR RESIDENTIAL USE

Now with

Built in

Radio Receiver

315 MHz

Now with

Built in

Radio Receiver

315 MHz

Your model may look different than the model illustrated in this manual.

INTENDED FOR PROFESSIONAL

INSTALLATION ONLY.

Visit www.Raynor.com to locate a

professional installing dealer in your area.

Serial #

(located on electrical box cover)

Installation Date

2 YEAR WARRANTY

OPERATOR RATING: 12 cycles per hour,

50 cycles per day; maximum.

SAFETY INFORMATION 3

APPLICATION 4

OPERATOR SPECIFICATIONS 5-6

Weights and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 5

Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mechanical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CARTON INVENTORY 6

PREPARATION 7

Preparing Your Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Handing Identification . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ASSEMBLY 7

TYPICAL INSTALLATION 8-14

Determine Mounting Location for Operator . . . . . . . . . . 8

Install the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

Install Emergency Disconnect System . . . . . . . . . . . . . 10

Power and Ground Wiring Connections . . . . . . . . . 11-12

Install 3-Button Control Station . . . . . . . . . . . . . . . 12-13

Setup Radio Antenna . . . . . . . . . . . . . . . . . . . . . . . 13-14

ADJUSTMENT 15

Adjust the Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjust the Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ENTRAPMENT PROTECTION 16-19

LiftMaster Monitored Entrapment Protection (LMEP) . . 16

Install the Photoelectric Sensors (Provided). . . . . . . . . 17

Mount the Photoelectric Sensors . . . . . . . . . . . . . . . . . 18

Entrapment Protection Wiring Options . . . . . . . . . . 18-19

LOGIC BOARD LAYOUT 19

BASIC PROGRAMMING 20-23

Determine the Wiring Type. . . . . . . . . . . . . . . . . . . 20-21

Remote Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22

Timer-to-Close (TTC) . . . . . . . . . . . . . . . . . . . . . . . 22-23

TESTING 23

EMERGENCY DISCONNECT 24

TROUBLESHOOTING 25-26

DIAGRAM 26

ACCESSORIES 27

CONTROL CONNECTION DIAGRAM BACK COVER

TABLE OF CONTENTS

SAFETY INFORMATION

Mechanical

Electrical

WARNING

CAUTION

IMPORTANT NOTES:

• BEFORE attempting to install, operate or maintain the operator,

you must read and fully understand this manual and follow all

safety instructions.

• DO NOT attempt repair or service of your commercial door and

gate operator unless you are an Authorized Service Technician.

When you see these Safety Symbols and Signal Words on the

following pages, they will alert you to the possibility of serious

injury or death if you do not comply with the warnings that

accompany them. The hazard may come from something

mechanical or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will

alert you to the possibility of damage to your door and/or the door

operator if you do not comply with the cautionary statements that

accompany it. Read them carefully.

To reduce the risk of SEVERE INJURY or DEATH:

IMPORTANT INSTALLATION INSTRUCTIONS

1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND

INSTRUCTIONS.

2. Install door operator ONLY on a properly operating, balanced

and lubricated door. An improperly balanced door may not

reverse when required and could result in SEVERE INJURY or

DEATH.

3. ALL repairs to cables, spring assemblies and other hardware

MUST be made by a trained door systems technician BEFORE

installing operator.

4. Disable ALL locks and remove ALL ropes connected to door

BEFORE installing operator to avoid entanglement.

5. Install door operator 8 feet (2.44 m) or more above floor.

6. NEVER connect door operator to power source until

instructed to do so.

7. NEVER wear watches, rings or loose clothing while installing

or servicing operator. They could be caught in door or

operator mechanisms.

8. Install control station:

• within sight of the door.

• out of reach of children at minimum height of 5 feet

(1.5 m).

• away from ALL moving parts of the door.

9. Install the control station far enough from the door to

prevent the user from coming in contact with the door while

operating the controls.

10. Install the entrapment warning placard on wall next to the

control station in a prominent location that is visible from

the door.

11. Place manual release/safety reverse test label in plain view

on inside of door.

12. Upon completion of installation, test entrapment protection

device.

13. SAVE THESE INSTRUCTIONS.

WARNING

SECTIONAL DOOR ROLLING DOOR

SQ. FT

24 ga. Steel 22 ga. Steel --- 20 ga. Steel

18 ga. Steel

16 ga. Steel

Aluminum Grilles Aluminum Doors ---

20 ga. Steel

Insulated

---

Fiberglass Aluminum Doors Wood Doors

NOTE: On steel insulated doors, a 24 ga. Back panel is assumed.

This operator includes a number of features that will provide years

of reliable and safe operation.

FEATURES:

• Supports both monitored and non-monitored entrapment

protection devices: Entrapment protection devices detect

obstructions in the door's path and automatically reverse a

closing door.

• Radio receiver: A factory installed radio receiver allows remote

controls, keyless entries and other remote command devices to

be programmed to the operator.

• Timer-To-Close: The Timer-to-Close feature allows the door to

automatically close after a preset time (only available with B2

wiring and a monitored entrapment protection device).

• Wiring Types: The functionality of the operator is based on the

wiring type. The operator is shipped from the factory in standard

C2 wiring type (factory default). Some wiring types will require

an optional monitored entrapment protection device. Refer to

Basic Programming Section for descriptions of wiring types,

requirements and programming.

Intended for use on vertical or high-lift sectional doors, or rolling door products. The MH operator is recommended for rolling sheet

doors. Not recommended for use on a standard lift sectional door.

Photoelectric Sensors

APPLICATION

---

--- 24 ga. Steel 20 ga. Steel --- 16 ga. Steel

Insulated

24 ga.

22 ga. Steel

20 ga. Steel --- 16 ga. Steel ---

--- --- ---

24 ga. Steel

Insulated

--- --- --- 20 ga. Steel

Insulated

16 ga. Steel

Insulated

320 275 250 200 160 120

MAXIMUM DOOR AREA (SQUARE FEET)

MODELS MH AND MJ

Hanging Weight: 60-70 LBS. (27.22-31.75 kg)

6.34"

(16.1 cm)

Hand Chain Wheel present

with Model MH only.

7.19"

(18.26 cm)

12.69"

(32.23 cm)

MOUNTING DIMENSIONS

A - Wall Mounting

B - Bracket Mounting (rolling door)

6.34"

(16.1 cm)

12.15"

(30.86 cm)

15.78"

(40.03 cm)

18.87"

(47.93 cm)

3.1"

(7.87 cm)

3.25"

(8.26 cm)

6.13"

(15.57 cm)

9.19"

(23.34 cm)

6.5"

(16.51 cm)

(17.78 cm)

14.75"

(37.47 cm)

OPERATOR SPECIFICATIONS

WEIGHTS AND DIMENSIONS

MOTOR

TYPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limited duty

HORSEPOWER: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 HP

VOLTAGE: . . . . . . . . . . . . . . . . . . . . . 115 Vac, Single Phase, 60 Hz

OPERATOR

CURRENT (Amperage):

Voltage-Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 HP

115-1Ø, 60Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2

ELECTRICAL

OPERATOR VOLTAGE: . . . . . . . . . . . 115 Vac, Single Phase, 60 Hz

WIRING TYPE: . . . . . . . . . . . . . . . . C2 (Standard) B2 Configurable

(See Basic Programming Section)

CONTROL WIRING: . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-22 AWG

SAFETY

DISCONNECT:

MH . . . . . . . . . . . . . . . . . . . . . . . . . . Floor level chain hoist for

manual chain hoist operation.

MJ. . . . . . . . . . . . . . . . . . . . . . . . . . . Floor level disconnect for

manual operation.

ENTRAPMENT PROTECTION:

LiftMaster Monitored Entrapment Protection (LMEP)

Photoelectric Sensors (CPS-U): . . . . . . . . . . . . . . . Through beam

used to provide non-contact safety protection.

Safety Edge (Optional): . . . . . . . . . Electric or pneumatic sensing

device attached to the bottom edge of door.

(see Accessory Page 27)

MECHANICAL

DOOR SPEED:. . . . . . . . . . . . . .Approximately 9" (23 cm) / second

depending on door setup

OUTPUT FORCE:. . . . . . . . . . . . . . . . . . . . . . . . . . 125 ft. lbs / sec.

OUTPUT RPM:

MJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 RPM

MH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 RPM

LIMIT ADJUST:. . . . . . . . . . . . Fully adjustable up to 14' door Max

DUTY: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Cycles per Hour Max

50 Cycles per Day Max

DRIVE TRAIN:. . . . . . . . . . . . . . . . . . . . Maintenance Free Bearings

FINISH: . . . . . . . . . . . . . Powder coated, Corrosion Resistant Steel

ENVIRONMENTAL

LOCATION: . . . . . . . . . . . . . . . . . . . . . . . . . . . .Indoor, dry location

OPERATING TEMPERATURE: . . . . . . . . . . . . . . . . .-4˚ F to + 122˚ F

(-20˚ C to + 50˚ C)

UL Listed to 40˚ C: Chamberlain tested to 50˚ C

OPERATOR SPECIFICATIONS

Before beginning your installation check that all components were provided. Your model may look different than the model illustrated.

CARTON INVENTORY

OPEN

STOP

OPEN

NOT SHOWN

Installation Manual

Quickstart Guide

User’s Guide

Entrapment Warning Placard

Installation Hardware Bag, Complete with: Master links (2), Wall bracket (1), Fastener Bag (1)

Door sprocket

3-Button Station

Operator

Warning Placard

Operator Drive

Sprocket

LiftMaster Monitored Entrapment Protection (LMEP)

Model CPS-U

Door/Operator

Chain

Hoist Hand Chain

Model MH ONLY

HANDING IDENTIFICATION

For MH model operators with manual hoist hand chain systems,

the handing of the operator must be determined at the time of the

order. The handing is indicated by last letter of the model name

(R or L). The illustration shown is a right-handed operator for

models MH and MJ series only. Left-handed operator will have

hoist chain on the left side.

The hand chain wheel can not be switched on site. If your

installation causes the hand chain to hang in the door opening,

hook the chain off to the side near the top of the door jamb.

Output Shaft

PREPARING YOUR DOOR

The manufacturer recommends 3 feet (91.4 cm) of clearance in front of operator for serviceability. Before you begin:

• Disable locks.

• Remove any ropes connected to door.

• Before the operator is installed, be sure the door has been properly aligned and is working smoothly. Although each installation will

vary due to particular building characteristics, refer to the following general procedures to install the operator.

RIGHT-HANDED OPERATOR

MODEL SHOWN: MH5011URCHB

PREPARATION

RIGHT-HAND ASSEMBLY LEFT-HAND ASSEMBLY

Operator Drive

Sprocket

Drive Shaft Operator Drive

Sprocket

Drive Shaft

Install operator drive sprocket.

ASSEMBLY

DETERMINE MOUNTING LOCATION FOR OPERATOR

Optimum Distance

12"-15"

Optimum Distance

12"-15"

The operator may be mounted on the wall, shelf or bracket (not provided, see accessories or door manufacturer). The optimum

distance between the door shaft and operator drive shaft is 12-15 inches.

WALL MOUNT SHELF OR BRACKET MOUNTING

Door Shaft

Operator

Drive Shaft

Door Shaft

Operator

Drive Shaft

TYPICAL INSTALLATION

NOTE: The illustrations may not depict your installation.

INSTALL THE OPERATOR

Place door sprocket on door shaft.

Door Sprocket

Door Shaft

1Place operator door sprocket on operator.

Operator Drive

Sprocket

Drive Shaft

Optional Mounting Bracket.

See Accessories.

Wrap drive chain around operator sprocket.

Door Sprocket

Electrical Box

Operator Drive

Sprocket

Drive Chain

Wrap drive chain around door sprocket.

Door Sprocket

Drive Chain

Master Link

TYPICAL INSTALLATION

Door

Door Sprocket

Key

Operator Drive

Sprocket

Position the operator until chain is taut

(not tight). If chain is too tight, it may

cause damage to operator.

Keep door sprocket and operator door

sprocket aligned. If sprockets are not

aligned, they may cause premature

wear on the chain.

Secure both sprockets with key and set screw. If sprockets

are not secure, they may drift and cause damage to operator.

Set Screw

Door Sprocket

INSTALL THE OPERATOR

Secure operator to mounting surface using appropriate

method and hardware. Mounting template can be found on

carton.

TYPICAL INSTALLATION

INSTALL EMERGENCY DISCONNECT SYSTEM

Floor

4' above

floor

Wrap hand chain around hand chain wheel and through

chain guide.

Secure chain retaining bracket to wall 4 feet above the floor.

Connect the ends of the hand chain.

Hand

Chain

Hand Chain Wheel

Keyhole Bracket

Chain Retaining

Bracket

(with pad locking

provisions)

Secure keyhole bracket to wall 4 feet above the floor.

MODEL MH MODEL MJ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raynor Garagentoröffner Handbücher

Raynor

Raynor 545RGD Safety Signal Bedienungsanleitung

Raynor

Raynor ULTRA 3595RGDS 3/4 HP Bedienungsanleitung

Raynor

Raynor RapidCoil RC300 Series Bedienungsanleitung

Raynor

Raynor 3595RGD 3/4 HP Bedienungsanleitung

Raynor

Raynor SENTINEL III 84505RRGD Bedienungsanleitung

Raynor

Raynor Premium series 8500RGD Prodigy II Bedienungsanleitung

Raynor

Raynor Aviator II PREMIUM Series Gebrauchs- und Pflegehandbuch

Raynor

Raynor 8500WRGD Bedienungsanleitung

Raynor

Raynor Prodigy III Bedienungsanleitung

Raynor

Raynor Sergeant II STANDARD Series Bedienungsanleitung

Raynor

Raynor Navigator 1245RGD Bedienungsanleitung

Raynor

Raynor 3280RGDM Bedienungsanleitung

Raynor

Raynor Pilot 1265RGD Bedienungsanleitung

Raynor

Raynor PILOT 2265RGD Bedienungsanleitung

Raynor

Raynor Navigator 2245RGD Bedienungsanleitung

Raynor

Raynor Ultra II 8587RGD Bedienungsanleitung

Raynor

Raynor Safety Signal 3850RGD Bedienungsanleitung

Raynor

Raynor FliteStar-7 Bedienungsanleitung

Raynor

Raynor 87504RGD-267 Bedienungsanleitung

Raynor

Raynor 3255RGD Bedienungsanleitung

Raynor

Raynor 3245RGD 1/3 HP Bedienungsanleitung

Raynor

Raynor ControlHoist ATS2113X-CX Bedienungsanleitung

Raynor

Raynor CORPORAL II STANDARD Series Bedienungsanleitung

Raynor

Raynor Commander II Safety Signal 3240RGD Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung