Raz AP600 Bedienungsanleitung

RQD014ENr05 Rev.Date:2022-10-25

Mobile Shower

Commode Chairs

Raz-AP600(Z160)

Raz-SP600(Z260)

User and Dealer

Manual

BASIC UDI-DI: 628758RAZDESIGNINC2004V9

RQD014ENr05 Rev. Date: 2022-10-25

It is important that the Raz Mobile Shower Commode Chair be properly

assembled and that all adjustments be made carefully. Please ensure that the

user(s), dealer(s) and attendant(s) have read this manual and thoroughly

understood the safe operation of the Raz Mobile Shower Commode Chair. Up-

to-date manuals are available online at www.razdesigninc.com. For

clarification of any section of thismanual, contact your distributor or the

manufacturer.

MANUFACTURER

U.S.A. AND WORLDWIDE

Raz Design Inc.

135 Railside Rd, Toronto, ON, Canada M3A 1B7

1.877720.5678 / 416.751.5678

[email protected]

DISTRIBUTOR

CANADA

Dynamic Health Care Solutions

Mono, Ontario, Canada

519.942.8441 / 866.875.2877

info@dynamichcs.com

CHAIR CLASSIFICATION BASED ON MAXIMUM USER WEIGHT

AP600 / SP600

275 kg (605 lbs)

THIS DEVICE IS SUITABLE FOR TYPE A; HIGH USAGE (e.g. INSTITUTIONS) AND SHOULD NEVER

BE USED FOR ANY PURPOSE OTHER THAN ORIGINALLY INTENDED

Forward Stability

The casters on all models are equipped with dual-locks. The step-on

lever activates both the roll lock and the swivel lock. It is essential

that all casters on the shower chair be in an outward position

before engaging the locks for optimal forward and lateral stability.

If so equipped, disengage the optional directional caster lock before

rotating the rear caster to the rearward position and applying the

caster’s dual-locks.

USERS MUST NOT lean forward while sitting in the Raz Shower Chair

as this may cause the chair to tip forward.

USERS MUST NOT wheel down a ramp without an attendant who can

hold onto the chair during the descent.

CASTER LOCKS ARE NOT BRAKES! Never use caster locks to

slow down the shower chair when descending inclines as this

could cause the chair to tip in the direction of travel.

SAFETY I

Failure to comply may cause injury or

SAFETY WARNINGS TO CONSIDER FOR USER PURPOSES

RQD014ENr05 Rev. Date: 2022-10-25

Lateral Stability

USERS MUST NOT lean over the edge of a Raz Shower Chair as this

could cause the chair to tip.

USERS MUST NOT attempt to pick up objects from the floor by leaning

over and reaching –use a reacher or ask for assistance from an

attendant.

USERS MUST NOT position the Raz Shower Chair on a side slope as

this could cause it to tip.

Rearward Stability

USERS MUST NOT wheel up an incline on aSP600 without

ensuring that the optional rear anti-tippers are in place. The optional

anti-tippers must be ordered with the Raz-SP600 and properly

installed before wheeling on uneven surfaces.

Anti-Tippers –SP600

Anti-tippers are an option for the Raz-SP600. These are

recommended whenever the chairs are to be used on uneven

surfaces such as ramps or sloped floors, when used by lower-limb

amputees, when the rear wheels are movedforward from the factory-

set position or for any situations when rearward stability is

compromised.

Ramps and Other Inclines

Ramps and other surfaces that are not level (such as slopes into

wheel-in showers) must be tested with an attendant to ensure that

they don’t compromise the chair’s stability. A qualified healthcare

professional should be consulted to assist with this process.

DO NOT push or pull the Raz-AP600 up or down an incline or

ramp that exceeds a 1:12 grade (5° slope).

DO NOT allow any user to be propelled (pushed or pulled) in a

Raz-AP600 Shower Chair in any other manner than by an attendant.

THE REARWARD STABILITY OF THE RAZ-SP600 IS AFFECTED BY THE MOUNTING LOCATION OF

THE REAR WHEELS, THE PHYSICAL AND CLINICAL CHARACTERISTICS OF THE USER AND THE

ANGLE OF THE BACKREST. THE NEED FOR ANTI-TIPPERS SHOULD HAVE BEEN DETERMINED AT

THE TIME OF THE PRESCRIPTION OF THE RAZ-SP600 WITH CONSIDERATION OF THE USER’S

PHYSICAL ATTRIBUTES AND ENVIRONMENT. ANTI-TIPPERS MAY BE ORDERED AS A RETROFIT AT

ANY TIME IF IT IS DETERMINED THAT THEY ARE REQUIRED.

Immersion

The Raz Mobile Shower Commode Chair is not designed to be used

as a pool chair. Do not immerse the shower chair in whole or in part,

in water or any other liquid. Immersion may result in damage to the

shower chair.

IMPORTANT

RQD014ENr05 Rev. Date: 2022-10-25

Chlorine Exposure

Suitable for use in wet areas, but not pools and similarly corrosive

environments.

DO NOT store the device near pools because chlorine in the air

will cause the device to rust.

Transfers

The most dangerous part of using any shower chair is the transfer. Since every chair has different

stability characteristics, it is essential to carefully review and test the transfer technique to ensure

that the procedure is safe. Test transfers should be performed with an attendant who can prevent the

chair from tipping or moving during the transfer. If you feel that the transfers cannot be repeatedly

performed safely, contact a healthcare professional who is familiar with transfer techniques and

options. Individuals who have not learned safe transfer skills must seek assistance during transfers

and may require the use of a mechanical lift.

Transferring onto a Raz-AP600

ALWAYS lock all four casters in their outward position (front casters

positioned in the forwardposition/rear casters positionedto the rear)

for maximum chair stability.

Transferring onto a Raz-SP600

ALWAYS lock both front casters in their outward position (positioned

forward) and fully apply both wheel locks so that they securely engage

the rear wheels.

The wheel locks are designed to prevent the self-propelling wheels from

rotating. The dual-locks on the casters are designed to prevent the

casters from rotating and the caster forks from swiveling. Caster locks

and wheel locks DO NOT and CANNOT prevent the shower chair

from sliding/moving if the floor is slippery. A slippery floor can be caused

by dust, water, soap or any substance that does not allow the

casters/rear wheels to grip the floor securely.

Transfers should never be attempted with the shower chair

positioned on slippery surfaces. It is recommended that transfers be

performed on clean, dry, non-slippery surfaces. Hard surface flooring

such as tile, wood or concrete may not provide sufficient grip to

keep locked casters and/or rear wheels from sliding. A fully-carpeted

surface is optimal. Be aware that area rugs and shower mats can slide

on floors and thereby present a hazardous surface.

DO NOT stand on any part of the frame of the Raz Mobile Shower

Commode Chair.

NEVER use the footplates to assist in transfers. This could cause the

chair to tip. The footrests should be swung to the side or removed

entirely during transfers to provide unobstructed access to the shower

chair.

The Raz Mobile Shower Commode Chair is NOT intended for use as a

transportation device or a long-term seating system.

RQD014ENr05 Rev. Date: 2022-10-25

USERS SHOULD NEVER BE LEFT UNATTENDED IN A RAZ MOBILIE SHOWER COMMODE

CHAIR.

DO NOT LIFT A RAZ MOBILE SHOWER COMMODE CHAIR AND OCCUPANT BY THE ARMRESTS

OR FOOTRESTS!

ALWAYS BE SURE THAT THE SEAT IS PROPERLY

INSTALLED AND LATCHED. THE REAR HOOKS

MUST BE FULLY ENGAGED AND THE FRONT

BRACKETS MUST BE LATCHED AND LOCKED

AROUND THE FRONT SEAT SUPPORT TUBES.

BE SURE THAT WHEN THE CHAIR IS DELIVERED TO

THE CLIENT, SEAT INSTALLATION INSTRUCTION IS

GIVEN TO THE CLIENT AND/OR CAREGIVERS.

IMPORTANT

RQD014ENr05 Rev. Date: 2022-10-25

IMPORTANT !____________

THE RAZ-AP600 AND RAZ-SP600 IS INTENDED FOR FOLLOWING USE:

•AS AN AID FOR SHOWERING/BATING, GOING TO THE TOILET, AND FOR OTHER

ACTIVITIES ASSOCIATED WITH PERSONAL CARE AND PERSONAL HYGEINE;

•TO PROVIDE SUPPORT FOR THE BODY OF THE USER IN A SEATED OR RECLINED

POSITION;

•WITH OR WITHOUT THE ASSISTANCE FROM A CAREGIVER;

•OVER A STANDARD TOILET, OR AS A COMMODE WITH THE COMMODE PAN;

•IN INDOOR ENVIRONMENTS ONLY;

•IN BOTH TYPE A, HIGH USAGE (e.g. INSTITUTIONAL) ENVIRONMENTS AND IN HOME

ENVIRONMENTS

THE RAZ-AP600 AND RAZ-SP600 DOES NOT PERFORM ANY THERAPEUTIC OR

DIAGNOSTIC FUNCTIONS, AND ARE NOT INTENDED FOR USE FOR ANY THERAPEUTIC OR

DIAGNOSTIC PURPOSES. ALL PRODUCTS WITHIN THE RAZ FAMILY ARE NON-STERILE,

REUSABLE, NON-INVASIVE, AND NON-IMPLANTABLE.

THE RAZ-AP600 AND RAZ-SP600 IS INTENDED TO BE USED BY PEOPLE WITH MOBILITY

IMPAIRMENTS, WHO MAY HAVE DIFFICULTY IN STANDING OR KEEPING THEIR BALANCE

WHILE COMPLETING ACTIVITIES SUCH AS SHOWERING, GOING TO THE TOILET, OR

PERSONAL HYGIENE. TYPICAL USERS HAVE LIMITED ENDURANCE AND POSTURAL

CONTROL, AND MAY REQUIRE ASSISTANCE FROM A CAREGIVER FOR ACTIVITIES SUCH

AS SHOWERING, GOING TO THE TOILET, OR PERSONAL HYGIENE. FOR PRODUCTS WITH

RECLINE FUNCTION, USE OF THE RECLINE FUNCTION MAY BE CONTRA-INDICATED

WHERE THE USER IS SENSITIVE TO SHEARING FORCES ON SEATED SURFACES WHEN

OPENING THE SEAT-TO BACK-ANGLE

CAUTION !__________

RISK OF BURNING YOUR SKIN

THE PRODUCT COMPONENTS CAN HEAT UP WHEN EXPOSED TO EXTERNAL SOURCES

OF HEAT.

•CONSIDER HEATED UP SURFACES WHEN USING THE SHOWER AND TOILET CHAIR

WHEN IT IS EXPOSED TO HOT WATER

•DO NOT EXPOSE THE PRODUCT TO DIRECT SUNLIGHT BEFORE USE

RQD014ENr05 Rev. Date: 2022-10-25

We have improved the design of our front seat brackets. Similar to the original design in its provision of

stability, this design also provides improved durability and functionality.

Please refer to the above image for the installation procedure.

Note: Please install the Phillips Pan Head Screws by hand. The use of power tools may cause the bracket to

deform.

After installation, ensure the brackets are secured onto the seat. Open and close the brackets to check for

proper functionality.

Always be sure that the seat is properly installed and latched. The rear hooks must be fully engaged and the

front brackets must be latched and locked around the front seat support tubes.

TORONTO, CANADA

FRONT SEAT BRACKET INSTALLATION (IF APPLICABLE)

RQD014ENr05 Rev. Date: 2022-10-25

USER & DEALER MANUAL TABLE OF CONTENTS

1.0 GENERAL INFORMATION

1.1 Raz-AP600/SP600 Mobile Shower Commode Chairs Overview.........................................9

1.2 Raz-AP600/SP600 Mobile Shower Commode Chairs Specifications..................................9

2.0 SET-UP: INTENDED FOR DEALER USE ONLY

2.1 Backrest Installation.........................................................................................................10

2.2 Raz Seat Installation ........................................................................................................10

2.3 Caster Installation ............................................................................................................11

2.4 Wheel Installation With Standard Axle Bolt –SP600 Model .............................................11

2.5 Adjustable Footrest Installation ........................................................................................12

2.6 Fastener Installation.........................................................................................................12

3.0 ADJUSTMENTS: INTENDED FOR DEALER USE ONLY

3.1 Backrest Adjustment........................................................................................................13

3.1.1 Backrest Angle Adjustment...................................................................................13

3.1.2 Adjustable-Tension Back Upholstery Adjustment..................................................13

3.2 Molded Seat Adjustment..................................................................................................13

3.3 Seat-To-Floor Height Adjustment.....................................................................................14

3.3.1 Seat-To-Floor Height Adjustment –AP600 Model ................................................14

3.3.2 Seat-To-Floor Height Adjustment –Front Casters of SP600 Model .....................14

3.3.3 Seat-To-Floor Height Adjustment –Rear Wheels of SP600 Model ......................14

3.4 Fore/Aft Adjustment of Rear Wheels –SP600 Model.......................................................15

3.5 Wheel Lock Adjustment –SP600 Model ..........................................................................15

3.6 Adjustable Footrest Adjustment........................................................................................15

4.0 USE AND OPERATION

4.1 Adjustable-Tension Back Upholstery................................................................................16

4.2 Molded Seat.....................................................................................................................16

4.3 Casters ............................................................................................................................17

4.4 Adjustable Footrests ........................................................................................................18

4.5 Wheel Locks –SP600 Model ...........................................................................................18

4.6 Commode Pan.................................................................................................................18

5.0 CLEANING AND MAINTENANCE

5.1 Cleaning After Each Use..................................................................................................19

5.1.1 Commode Pan......................................................................................................19

5.1.2 Molded Seat.........................................................................................................19

5.2 Cleaning As Needed........................................................................................................19

5.2.1 Adjustable-Tension Back Upholstery....................................................................19

5.2.2 Frame, Armrests, Adjustable Footrests, and Other Components..........................19

5.3 Suggested Cleaning Products..........................................................................................19

6.0 LIMITED WARRANTY.................................................................................................................20

7.0 CONTACTS.................................................................................................................................21

RQD014ENr05 Rev. Date: 2022-10-25

1.0 GENERAL INFORMATION

1.1 Raz-AP600/SP600 Mobile Shower Commode Chairs Overview

1.2 Raz-AP600/SP600 Mobile Shower Commode Chairs Specifications

SPECIFICATIONS

Raz-AP600

Raz-SP600

WEIGHT CAPACITY

275 kg (605 lbs)

FRAME WIDTH

(seat and back frames)

22” (56cm)

OVERALL WIDTH

26.5” (67cm)

30” (76cm)

OVERALL LENGTH

(with footrests)

36” (91cm)

40” (101.5cm)

SEAT WIDTH (commode seat)

23” (58cm)

SEAT DEPTH

(front of back post to front of seat)

18” (46cm)

CLEARANCE HEIGHT

5” casters with pan brackets:

5” casters without pan brackets:

6” casters with pan brackets:

6” casters without pan brackets:

14.25”-18.25” (36-46cm)

15”-19” (38-49cm)

15.25”-19.25” (39-49cm)

16”-20” (41-51cm)

15.25”, 16.25” (39cm, 41cm)

16”, 17” (40.5cm, 43cm)

16.25”, 17.25”, 20.25” (41cm, 44cm 51.5cm)

17”, 18”, 21” (43cm, 46cm , 53cm)

ARMREST HEIGHT ABOVE SEAT

9.5” (24cm)

SEAT-TO-FLOOR HEIGHT

19”-23” in 1” increments

(48-58cm)

5” casters: 20”, 21” (51cm, 53cm)

6” casters: 20”, 21”, 24” (51cm, 53cm, 61cm)

PRODUCT WEIGHT

(with footrests)

With 5” casters:

With 6” casters:

54.5 lbs (25 kg)

56.5 lbs (26.7 kg)

68 lbs (30.9 kg)

69 lbs (31.3kg)

FRAME AND HARDWARE

MATERIAL

Stainless Steel (Lifetime warranty against corrosion)

MINIMUM TURNING CIRCLE

41.5” (105 cm)

64” (163 cm)

RQD014ENr05 Rev. Date: 2022-10-25

2.0 SET-UP: INTENDED FOR DEALER USE ONLY

2.1 Backrest Installation

Tools required: 6mm hex key, 13mm wrench

1. Remove the shower chair from the shipping carton.

2. Lift the backrest to an upright position.

3. Insert the button head cap screw through one of the two holes in

the middle of the outer backrest plate.

NOTE: Select the rear hole for a 95° backrest or front hole for 100°

backrest angle.

TIP: A Phillips screwdriver can be inserted through one plate and

frame to temporarily secure the backrest in an upright position.

4. Fasten the other end of the screw with a nyloc nut.

5. Tighten the assembly with the hex key and wrench until the end

of the screw extends 1 or 2 threads beyond the nylon locknut.

6. Repeat steps 3 to 5 for other frame tube.

TOP VIEW OF BACKREST ASSEMBLY

2.2 Raz Seat Installation

1. Ensure that the front spring brackets are in the open position.

To open the front brackets, squeeze to unlatch.

2. Slide the rear of the seat over the rear cross tubes as the

front of the seat is lowered onto the frame. Check to make

sure that the rear seat brackets hook below the cross tubes.

3. Continue lowering the front of the seat until the front seat

brackets nestle onto the front seat support tubes.

4. Secure the seat in place by closing the front seat brackets.

To close the seat bracket, squeeze the clip and close

the bracket around the front support tubes.

5. Reverse steps 1 to 4 to remove the seat from the frame.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Raz Mobilitätshilfe Handbücher

Raz

Raz AT600 Bedienungsanleitung

Beliebte Mobilitätshilfe Handbücher anderer Marken

Alber

Alber Scalamobil iQ Bedienungsanleitung

Ferno

Ferno CCT-PX Bedienungsanleitung

HEPRO

HEPRO Gripo Bedienungsanleitung

Otto Bock

Otto Bock Pheon 3R62 Bedienungsanleitung

NRS Healthcare

NRS Healthcare M11090 Bedienungsanleitung

Medline

Medline MDS86835DSHEC Installationsanleitung

Guldmann

Guldmann Twin Turner II Bedienungsanleitung

Drive

Drive ROOMBA Bedienungsanleitung

Gate

Gate Balder Bedienungsanleitung

Decon wheel

Decon wheel TNS Notos Bedienungsanleitung

ExoAtlet

ExoAtlet ExoAtlet-II Bedienungsanleitung

Invacare

Invacare Storm Series Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare B3800F Bedienungsanleitung

AMF-BRUNS

AMF-BRUNS PROTEKTOR Bedienungsanleitung

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Bedienungsanleitung

Rhythm Healthcare

Rhythm Healthcare C500U Bedienungsanleitung

Lumex

Lumex RJ4200A Bedienungsanleitung

Rebotec

Rebotec Jumbo Bedienungsanleitung