RCTECH GT-4160 Bedienungsanleitung
GT-4160
720p HD FPV
4 Channel RC Quadcopter
Quadcopter Overview
Remote Control Overview
Headless Mode Explained
Remote Control Battery & Pairing
Remote Control Mode
FPV Screen
Rotor Guards & Landing Struts
Charge the Quadcopter
Preparation and Pairing
Flight Control and Trim
1
2
3
4
5
6
7
8
9
10
360° Flip
Troubleshooting
11
12
Parts List
13
1. QUADCOPTER OVERVIEW
Propeller Blades
(Rotors)
Main Shell
Rotor Guard
Motor
2. REMOTE CONTROL OVERVIEW
Place the quadcopter 2 metres in front of you with the nose facing away from you, after lift off, long press the Headless
Mode button for over 2 seconds to enter Headless Mode. Long press the Headless Mode Button for over 2 seconds to
exit Headless Mode.
Headless Mode allows the quadcopter to operate in such a way so that the orientation remains in its initial state, no
matter which way the quadcopter is facing at the time. For example, if the quadcopter lifted off facing the front (facing
away from you) and then turned 90° to the left, when entering Headless mode, the quadcopter is going to assume its
now right side as the front, so if you push forward, the quadcopter is going to move forward (facing away from you),
rather than to the left.
Headless mode makes it easy for beginners to control the quadcopter when it is difficult to establish the orientation, and
it is an easy way for you to retract the quadcopter, simply push backward, and the quadcopter will fly towards you.
3. HEADLESS MODE EXPLAINED
1Antenna
2 Light Control
3 Power LED
4 Power Switch
5 Flip Button
6 Throttle Stick / Left & Right Turn Stick
7 Direction Control Stick
8 Left & Right Turn Trim
9 Throttle Trim
10 Left & Right Move Trim
11 Forward & Backward Trim
12 Video Button
13 LCD Display
14 Mode Switch
15 Photo Button
16 Sensitivity Switch
17 Headless Mode
Turn ON/OFF LED Lights on quadcopter
Turn ON/OFF the remote control
Perform 360° flip
Ascend & descend / Turn left & right
Move forward, backward, left & right
Adjust a deviation to the left or right
Adjust throttle power
Adjust a lean to the left or right
Adjust a tilt to the front or back
Record Video
Switch between Mode 1 and Mode 2
Take photo
Remote Control Signal Strength
Remote Control Mode
Throttle Trim Level Indicator
Light Control Indicator
Left & Right Turn Trim Level Indicator
Remote Control Battery Level
Take Photo
Forward & Backward Move Trim Level Indicator
Record Video
Left & Right Move Trim Level Indicator
Channel and Sensitivity Indicator
Indicates ON/OFF
Transmission
Displays Information
Adjust flight control sensitivity
Turn ON/OFF Headless Mode
4. REMOTE CONTROL BATTERY AND PAIRING
Battery Cover
4 x AABatteries (Not Supplied)
Slide open the battery cover on the back of the
remote control. Insert 4 x AAsized batteries in
the polarity as shown on the inside of the
battery compartment. Batteries of different
type are not to be mixed.
To pair the remote control with your quadcopter. First switch on the power of your quadcopter, the LED indicators
would now start flashing. Then make sure the throttle stick is pushed to the lowerst position, now turn on the remote
control’s power switch. Push the throttle stick to the highest and then to the lowest again. There will be a beep sound
and the quadcopter’s LED indicator stops flashing and remains steady. The paring is now complete and ready to fly.
5. REMOTE CONTROL MODES SWITCHOVER
This quadcopter remote control allow you to switch between different modes and customise the function of the control
sticks.
By default the remote control will be in Mode 1 with the following functions:
Throttle Stick
/ Left & Right
Turn (Rotate)
Direction Control Stick
Forward & Backward Move
Left & Right Move
By pressing the Mode Switch Button, the remote control goes into mode 2, the Left & Right Turn function is switched
with the Left & Move function.
Mode Switch Button
Throttle Stick
/ Left & Right
Move
Direction Control Stick
Forward & Backward Move
Left & Right Turn (Rotate)
Mode Switch Button
2
You can even swap the side of Throttle Stick (non-return to center) with the Direction Control Stick (return to center).
First switch off the remote control, then simply press the 2 clips holding the sticks in place and lift them out of the
socket and swap side. You can still switch between mode 1 and mode 2 after you have swapped the physical sticks.
6. FPV SCREEN
This quadcopter is equipped with a 720P HD camera and transmits live images to the 14.33cm FPV screen via 5.8GHz.
To use the FPV screen, please first charge the FPV screen using the supplied USB Charger. Once fully charged (the
red light on the charger turns on, charging time about 100 minutes), attach the antenna on the top right hand corner.
You can choose to dock the FPV screen on the remote control, there is however no hard wiring so you can use
the screen anywhere.
The power switch is located on the right hand side of the screen. Once the quadcopter is switched on (with the HD
camera connected), the screen will automatically display transmission. By pressing the Video or Photo button on the
remote control, the microSD card in the HD camera is going to record video and take photos respectively.
Record Video Take Photo
Removable
Hood
Docking
Connector Charging Socket
Power Switch
7. ROTOR GUARDS AND LANDING STRUT
1. Included in the package you will find a screw driver, 2 x landing struts and 4 x rotor guards.
2. The 2 x landing struts will fit into the pre-drilled holes on the bottom of the quadcopter, use the screw driver to
tighten the screws.
3. The 4 x rotor guards will fit into the pre-drilled holes around each of the 4 rotors. Use the screw driver to tighten
the screws.
Screws Screws
8. CHARGE THE QUADCOPTER BATTERY
Plug the USB charging cable into a USB power socket such as your PC, the charging indicator light will turn green.
Connect the rechargeable battery to the charging cable, indicator will then turn red. Once charging is complete,
indicator turns to green again.
Charging time is around 100 minutes.
9. PREPARATION & PAIRING
1. Please operate this quadcopter in spacious environment, avoid crowds, power lines and other obstructions. Avoid
using the quadcopter in bad weather as rain and wind may damage the unit.
2. Insert the quadcopter battery (Li-Polymer) into the quadcopter, the LED indicator will light on and immediately start
flashing. Make sure the quadcopter is level on the ground.
3. On your remote control, make sure the throttle stick is pushed to the lowerst position, then turn on the remote control’s
power switch. Now push the throttle stick to the highest and then to the lowest again. There will be a beep sound
and the quadcopter’s LED indicator stops flashing and remains steady. The paring is now complete and ready to fly.
10. FLIGHT CONTROL AND TRIM
ASCEND
&
DESCEND
Use the throttle stick to ascend or descend. Push the throttle
upwards to increase throttle and downward to decrease throttle.
TURN
LEFT &
RIGHT
Use the throttle stick to turn left or right. Push the throttle
left to turn left and right to turn right.
MOVE
FORWARD &
BACKWARD
Use the direction control stick to move forward or backward.
Push the direction control upward to move forward and downward
to move backward.
MOVE
LEFT &
RIGHT
Use the direction control stick to move left or right.
Push the direction control left to move left and right to move
right.
LEFT &
RIGHT MOVE
TRIM
If the quadcopter leans to the left or right when hovering, use
the left and right move trim button to adjust to the opposite
direction.
FORWARD &
BACKWARD
TRIM
If the quadcopter tilts forward or backward when hovering, use
the forward and backward trim button to adjust to the opposite
direction.
11. 360° FLIP
When in flight, you can press the flip button on the top right hand corner of the remote control to perform a flip. Once
you press the flip button, the quadcopter’s LED indicator will start to flash and you will hear a continuous beep sound.
Ascend the quadcopter to at least 2 metres high, and then push the direction control stick to the bottom in any
direction. You will see the quadcopter flip 360°.
12. TROUBLESHOOTING
NOITULOSESUACELBISSOPMELBORP
LED indicators remains flashing on the
quadcopter after powering on. 1. Pairing between the remote control
and quadcopter was not successful.
2. Battery is near depletion
1. Repeat the pairing steps.
2. Charge battery.
Propeller blades keeps spinning but
unable to lift off.
1. Propeller blades damaged.
2. Quadcopter battery is near
depletion.
1. Replace the damaged blade.
2. Charge the quadcopter battery.
Quadcopter vibrates abnormally. Propeller blades damaged. Replace the damaged blade.
Quadcopter still leans or turns to a
direction even after adjusting the trims. 1. Propeller blades damaged.
2. Motors damaged. 1. Replace the damaged blade.
2. Replace the damaged motor.
After a crash, quadcopter unable
to fly again. 1. Motor is damaged or displaced.
2. Gear is loose. 1. Replace motor.
2. Tighten the gear.
13. PARTS LIST
Top
Shell Bottom
Shell Clockwise
Rotor
Blades
Reverse
Rotor
Blades
Anti-Clockwise
Motor
Reverse
Motor Li-Polymer
Battery Receiver
Board USB
Charging
Cable
Geared
Shaft Rotor
Guard Landing
Strut LED
Lights Screwdriver
Inhaltsverzeichnis
Andere RCTECH Quadcopter Handbücher
