Recoil RED600.1 Bedienungsanleitung

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA60 0.4

RED600.1/RED1200.1/REA600.4

CAR AUDIO AMPLIFIER

User Manual

INTRODUCTION

CAUTION

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

Thank you for purchasing a Recoil amplifier for your car audio system. You have

chosen Recoil because you deserve the best!

Please thoroughly read through this manual before getting started. If you have

any questions and require additional assistance, please contact support@re-

coilaudio.com.

GENERAL PRECAUTIONS

• This unit is designed for negative ground 12V DC operation only.

• Total system impedance must not be less than 2 ohms, in a bridged OR stereo

configuration (monoblocks are 1 ohm stable)

• Do not cover the amplifier with carpet or wires.

• For safety reasons, keep the volume of your car audio system moderate while

driving your vehicle so that you can still hear normal traffic sounds and emergen-

cy vehicles outside your car.

MOUNTING PRECAUTIONS

Choose a location that provides adequate ventilation around the amplifier. For

easy system set-up, mount the amplifier so the side panel controls will be accessi-

ble after

installation. In addition, observe the following precautions:

1. Using a felt pen mark, mark the mounting hole locations.

2. Mounting the amplifier on carpet will significantly reduce air flow, resulting in

reduced thermal run times.

3. Mount the amplifier on a solid surface. Avoid mounting to sub woofer enclo-

sures or areas prone to vibration.

4. Prior to mounting the amplifier, make sure not to cut or drill into the fuel tank,

fuel lines, brake lines (under chassis) or electrical wiring.

WIRING PRECAUTIONS

1. Before installation, make sure the source unit power switch is in the OFF position.

2. Disconnect the negative (-) lead of the battery before making any power

connections.

3. When making connections, be sure that each one is clean and secure.

4. A secure clean ground connection is critical to the performance of your ampli-

fier. Connect the ground directly to the car chassis to minimize resistance and

avoid any noise problems.

5. Add an external fuse on the amplifier's positive (+) power lead and connect it

as close as possible to the vehicle's (+) battery terminal. 18 inches is the usual

dimension.

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

BATT ( 12V POWER )

Before mounting amplifiers, disconnect the negative cable from the battery to

protect any accidential damage to your amplifiers and audio system.

Connect the power cables to power terminal 12V.

Connect one end of fuse holder to the power cable going into the amplifiers and

the other end of fuse holder to positive battery. This fuse location will protect the

system and the vehicle against the possibility of a short circuit in the power cable.

Be sure to use fuses and fuse holder adequate for the application.

GND ( GROUND)

Locate a secure grounding connection as close to amplifier as possible.

Make sure the location is clean and provides a direct electrical connection to the

frame of the vehicle. The ground needs to have as low of a resistance as possible.

Connect one end of a short piece of the same size cable as the power cable to

the grounding point or to one of your batteries or battery bank. Run the other end

of 4 ga cable to the mounting location of the amplifiers for connection to the

amplifiers ground terminals and connect the ground cable to the GND (ground

terminal).

REM ( REMOTE )

Run a remote turn on cable from the switched 12V source . This may be a toggle

switch, a relay, your source unit's remote trigger cables, or power antenna trigger

cable. Connect the remote turn on cable to the REM ( remote ) terminal.

SPEAKER TERMINAL BLOCK

Connect speaker cables from speaker terminal block to subwoofers. Subwoofers

impedance should be check carefully.

HEAD UNIT

GROUND GROUND

FUSE-HOLDER

BATTERY

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

FRONT PLATE

RCA INPUTS

The RCA jacks allow for a normal Left and Right channel signal input. Simply

connect to the source unit using RCA type audio cables, keeping them away

from power wiring wherever possible to reduce risk of noise.

RCA OUTPUTS

The RCA outputs connect another amplifier for multi amplifiers system.

GAIN

The input gain control is preset to match the output of most source units. It can be

adjusted to match output levels from a variety of source units.

SUBSONIC

This control allows you to remove the unwanted sub-sonic frequencies below the

tuning frequency of a ported enclosure. This helps to protect the woofer from over

excursion. Adjustable from 10 - 50Hz.

BASS BOOST

This control adds 0 to +9dB of boost at 45Hz. Be cautious when adding boost to

some subwoofer systems as they may not be able to handle the additional low

frequency boost. In the 0dB position, no bass boost is added.

LPF

Use this adjustment to select the crossover point. Remember that you must select

the Low Pass position (LPF) of the crossover adjustment switch first. The range of

adjustment is limited between 35 - 250 Hz.

REMOTE

This port is for the remote level control. The control is intended to allow the user to

control the level of the amplifier from your driver's seat.

POWER & PROTECT INDICATORS

These lights indicate when the amplifier is powered up normally and when there is

a protection fault. The Protect LED is laminated when there is a problem with your

amplifier.

RED600.1 & RED1200.1

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

FRONT PLATE

RCA INPUTS

The RCA jacks allow for a normal Left and Right channel signal input. Simply connect to the source unit

using RCA type audio cables, keeping them away from power wiring wherever possible to reduce risk

of noise.

RCA OUTPUTS

The RCA jacks allow for a“Pass Thru”from REA600.4 amplifier to a mono block amplifer

(RED600.1D/RED1200.1D) signal input. This simplifies signal connection in a Front/Rear/Sub system with

an aftermarket headunit that only has a 2 or 4 Ch output.

Signal Input Switch

This switch allows the amplifier to be driven with either 2 or 4 pairs of inputs.

GAIN

The input gain control is preset to match the output of most source units. It can be adjusted to match

output levels from a variety of source units

HPF

Use this adjustment to select the crossover point. Remember that you must select the High Pass position

(HPF) of the crossover adjustment switch first. The range of adjustment is limited between 15 - 350 Hz.

X-OVER

This switch allows you to select the crossover. Use HPF(high pass filter) for midrange or high frequency

speakers. Use LPF(low pass filter) for subwoofers. In the FULL position, neither crossover adjustment knob

has an affect and all speakers will receive the full frequency range.

LPF

Use this adjustment to select the crossover point. Remember that you must select the Low Pass position

(LPF) of the crossover adjustment switch first. The range of adjustment is limited between 35 - 350 Hz.

BASS BOOST

This control adds 0 to +12dB of boost at 45Hz. Be cautious when adding boost to some subwoofer

systems as they may not be able to handle the additional low frequency boost. In the 0dB position, no

bass boost is added.

POWER & PROTECT INDICATORS

These lights indicate when the amplifier is powered up normally and when there is a protection fault.

The Protect LED is laminated when there is a problem with your amplifier.

REA600.4

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

RCA INPUT WIRING DIAGRAM

SPEAKER CONNECTION DIAGRAM

HEAD UNIT

HEAD UNI

RED600.1 & RED1200.1

Caution !!

REA600.4

RED600.1&RED1200.1 minimum working impedance is 1Ohm

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

SPEAKER CONNECTION DIAGRAM

REA600.4

Caution !!

REA600.4 minimum working impedance is 2Ohm

Caution !!

REA600.4 minimum bridge working imededance is 4Ohm

CAR AUDIO AMPLIFIER RED600.1/RED1200.1/REA600.4

SPECIFICATONS

TROUBLE-SHOOTING

Echo series amplifiers have protection features to prevent any damages from

misuse or faulty conditions.

If Echo series amplifiers sense excessive heat, short circuited speakers DC, or

voltage, the protection indicator will light, and the system will be turned off.

In order to check the problem, you should turn all levels down and all power off

and carefully check the installation for wiring mistakes or short.

If Echo series amplifiers shuts down due to excessive heat, They will be working

later when it is cooled down before removing your amplifier, refer to the list

below and follow the suggested procedures.

NO SOUND ( NO OUTPUT)

Please check all connections, cables' rounting, short & voltage.

Please check the fuses , If they are blown, please replace with new one.

Please check whether speakers work well, you can test speakers by connecting

to another amplifier.

Model

RMS power @ 4 ohm

RMS power @ 2 ohm

RMS power @ 1 ohm

RMS power @ 4 ohm mono

Frequency Response

Signal to Noise

Efficiency @ 4 ohm

Input Sensitivity

Subsonic Filter

High Pass Fitter

Low Pass Filter

Bass Boost

Remote Control

Fuse Rating(ATC)

Dimensions(mm)

RED600.1

1 x 350W

1 x 550W

1 x 650W

N/A

15Hz - 270Hz

≥ 85dB

Over 90%

12V - O.2V

10Hz - 50 Hz

N/A

35Hz - 250Hz

0dB - 9dB

Included

35A x 2

9.84”(250mm)

x 7.59”(193mm)

x 2.2”(56mm)

RED1200.1

1 x 550W

1 x 900W

1 x 1200W

N/A

15Hz - 270Hz

> 85dB

Over 90%

12V - O.2V

10Hz - 50 Hz

N/A

35Hz - 250Hz

0dB - 9dB

Included

30A x 4

13.77”(350mm)

x 7.59”(193mm)

x 2.2”(56mm)

REA600.4

4 x 95W

4 x 130W

N/A

2 x 280W

15Hz - 20kHz

> 90dB

Over 65%

12V - O.2V

N/A

15Hz - 350Hz

35Hz - 350Hz

N/A

35A x 2

15.74”(450mm)

x 7.59”(193mm)

x 2.2”(56mm)

DISTORTION & NOISE

Readjust input level and check the speaker quality at another amplifier. Replace

poor quality speakers with good quality ones.

Check amplifiers and headunit's ground contact. all grounds should be common.

Check RCA Jack, then repalce with new one or reroute RCA cable.

Engine noise is caused by poor grounding of amplifiers, headunit, other compo-

nents, battery or alternator, so please check all grounding connection.

POOR BASS RESPONSE

Please check speaker cables and reverse polarity.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Recoil Verstärker Handbücher

Recoil

Recoil DI550.4 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung