RedBack Lasers BASIC614 Bedienungsanleitung

Models Covered; BASIC614, EL614, EL614S & EL614GM

CONTENTS

User Safety 2

Introduction and EL614™ Accessories 3

EL614™Diagram 4

Operating Instructions 7

Batteries 7

Power 8

Tilt Mode 8

V-W-S 9

Rotation Speed 9

Setting Grades (needs remote - EL614S & EL614GM) 10

Laser Receiver LR715 (BASIC614, EL614 & EL614S) 11

Laser Receiver LR720T (EL614GM Kit only) 12

Calibration Self Check & Technical Specications 14

Care & Maintenance, Trouble Shooting 15

Warranty 16

User Safety

• Laser output sign lies near the output aperture.

• Do not stare directly into laser beam.

• Do not disassemble the instrument or attempt to

perform any internal servicing. Repairs and service

should be performed only authorised service

centres of Redback Lasers.

• This instrument complies with the safety

Classication standards of laser radiation.

CAUTION: Class II laser <1mW at 635nm.

Do NOT stare into laser beam or aim at

another person.

Follow relevant Australian Standards

Copyright © CMI LasersTM RedBack lasersTM and Level1LasersTM . All rights reserved CMI Industries Pty Ltd 2016Copyright © CMI LasersTM RedBack lasersTM and Level1LasersTM . All rights reserved CMI Industries Pty Ltd 2016

No artwork or photographs produced by CMI Industries Pty Ltd may be used copied or reproduced without the written consentNo artwork or photographs produced by CMI Industries Pty Ltd may be used copied or reproduced without the written consent

from CMI Industries Pty Ltdfrom CMI Industries Pty Ltd

EL614TM INTRODUCTION

Congratulations on purchasing the EL614™ an electronic self levelling

builders/concreters rotating laser level built tough.

The EL614™ can be purchased in a number of dierent congurations;

1) BASIC614 - LR715 Receiver, “C” Batteries

2) EL614 - LR715 Receiver, Ni-mh Battery

2) EL614S - Remote Control (grade) + LR715 Receiver, Ni-mh Battery

3) EL614GM + Remote + LR720T mm Receiver (grade Tracking), Ni-mh

These instructions cover all these congurations so may refer to Components such as remote or

receiver type or battery types that you may not have purchased in your 614 laser level kit.

The EL614™ has all the features you need for general site levelling; Tilt

provides protection from knocks and bumps shutting down rotation warning

you that the laser has moved. V-W-S (Vibration and Wind setting control)

allows you to continue to work in high wind or on sites close to machinery.

If you have purchased your EL614 with Remote then there is also a single

grade match feature.

The EL614™ Comes with Ni-Mh rechargeable batteries and charger (Not

BASIC614) as well as being able to operate with standard “C” Alkaline

batteries.

The EL614™ features RedBack Laser’s “Safety Cage” technology with consists

of a full steel internal chassis which protects the levelling components in the

event of an accident, Its Built Tough. Finally the EL614™ has a Five Year

Redback Warranty. (See page 16)

BASIC614 Kit Included Accessories

• EL614™ Laser Unit

• Protective Carry Case (Soft for Basic614 hard for rest)

• “C” Cell Battery Holder

• Laser Receiver LR715 & Clamp

EL614 Has in Addition

• Ni-mh Rechargeable Battery

EL614S Has in Addition

• Remote Control for manual grade

EL614GM Has instead of LR715 Receiver

• Millimetre Tracking Receiver for Auto Grade Match LR720T & Clamp

EL614TM DIAGRAMS

EL614TM Laser Unit

1. Laser Output Window

2. Rubberised Casing

3. Keypad

4. Battery Compartment

www.redbacklasers.com.au

EL614TM Safety Cage

Keypad

www.redbacklasers.com.au

Receiver - LR715

Reception Sensors

Fine/Coarse Mode

Speaker Control

Power On/O

Rubber Casing

LCD Display

(Repeated on rear)

Bubble Vial

Display back light

Power On/O

Tilt On/O

Rotation Speed

Vibration & Wind

Sensor Select

Axis LED’s

For Grade Setting (Remote required)

and calibration (service only)

Power LED

Magnetic Mounting

EL614TM DIAGRAMS

Receiver - LR720T mm Display (EL614GM Kit only)

Rubber Casing

Large Reception Window

LCD Displays (front/back)

with mm from Level

Power Button

Set Axis to grade track

Activate Grade

Tracking (long press)

Channel Setting

(short press)

Sound and

Backlight Options

Accuracy Settings

Remote Control - Grade Setting (EL614S & EL614GM Kits only)

Grade Setting Functions - Center

button selects axis - Up/Down buttons

slope up or down as required.

Scan Line Mode - Center button selects

arc of scan and left and right buttons

select position of scan line.

Standby Power Button for Laser - places

a powered up laser into stanby mode

and press again to awaken. Yellow

button is rotation speed.

Large Reception Window

www.redbacklasers.com.au

EL614TM OPERATING INSTRUCTIONS

Battery Instructions

To charge this battery pack simply inserting the charger plug into the charging

socket above the locking screw. The LED on the charger is illuminated red

during the charging process and will turn green once the batteries are

fully charged. Battery pack can be charged while inserted in the laser or

independently.

When the power LED on the keypad ashes, the rechargeable battery pack

needs recharging or standard batteries need replacing. Note the charger will

only charge the supplied rechargeable battery pack.

Handy Hints

•

Prior to initial use, charge the rechargeable batteries for at least 8

hours.

•

Running rechargeable batteries completely at will increase battery life.

•

The EL614™ can operate o mains by plugging the charger (for indoor

use only) into the unit.

•

Remember the EL614™ can operate using standard batteries when

rechargeable pack is out of charge.

The EL614 has two battery options either 4 x standard “C” size Alkaline

or the Ni-Mh rechargeable pack. For standard 4 x “C” alkaline operation

simply insert into standard battery holder in the direction indicated and slide

into battery recess and tighten the locking screw. (BASIC614 does not included

rechargeable battery and charger)

To use the rechargeable

battery pack rst

remove standard pack

if inserted and place

into the same battery

recess and tighten

locking screw.

Turning Laser On

Press Power button on the keypad to turn on the EL614™, power LED

will light. Batteries are low if power LED ashes. After turning the laser on,

the laser will auto level and rotate. The EL614TM has a large self levelling

range, if the laser happens to be set up outside this range, a warning will

sound and the lasers will ash. Re-set the laser more level if this occurs.

Tilt Mode

Tilt mode is somewhat similar to tilt on a pinball table in that if when running

the EL614 detects signicant disturbance or movement that could eect the

accuracy of your work the laser will “Tilt” (stop working) and the laser beams

will ash to indicate this. You will need to then re level the laser by pressing

the tilt button, note that the tilt is then disabled to re-enable press

the TILT button again so its LED light illuminates. After a few seconds the

laser will re-level, then re-check your work to maintain maximum accuracy.

Tilt mode is turned on and o with the tilt button on the keypad, the default

setting is o. Once the tilt button has been pressed the tilt LED will light

indicating it is on.

To deactivate the tilt mode press the tilt button the LED goes out. It

is recommended to use tilt mode when optimal accuracy is required or when

there is a chance that machinery or worker may interfere inadvertently with

the lasers level.

EL614TM OPERATING INSTRUCTIONS cont.

www.redbacklasers.com.au

Rotation Speed Settings

• A short press of the Rotating Speed Button will switch the rotating

speed between 3 dierent rotational speeds. Sometimes dierent

rotation speeds will provide better reception with the LR715 receiver

when being used at dierent distances from the laser. For most

situations the default speed (800rpm) will provide best results.

V-W-S Vibration & Wind Sensor Setting

The EL614 continuously self levels for utmost accuracy, in high winds or

vibrations the laser will stop rotating to re-level this may be inconvenient by

slowing down your work, however, by selecting V-W-S button the laser

continually re-levels but does not stop rotating whilst doing so.

10 www.redbacklasers.com.au

Setting Grades (requires remote control that comes with Grade & Grade +MM kits)

EL614TM OPERATING INSTRUCTIONS cont.

The EL614S & EL614GM kits come with a remote control that can set a

manual grade on one axis, it can be set to either the “X” or “Y” axis but

not both.

First set up the laser aligning the X axis with the direction of the required

grade rise/fall, the laser can be placed anywhere on site as long as the X

axis runs parallel or in line with the desired grade.

For this example we want a grade of 1 in 60 or 1.667% or in other words

for every 6m (6000mm) travelled away from the laser along the X axis we

want the laser plain to tilt down/up 0.1m (100mm).

To achieve this measure out 6m away from the laser along the X axis and

hold the sta at this point slide the receiver up/down the sta until the

receiver indicates level.

Then making a note of the height on the sta slide the receiver up/down

the sta 100mm from the level point, this is now the height the laser needs

to be hitting to be setting a 1 in 60 slope or grade.

Using the remote, select grade mode on the X axis and use the Slope Grade

Direction buttons to slope the laser until the receiver shows level (see page

6 for remote diagram).

The Grade is now set at 1 in 60 or 1.667% on the X axis and anywhere on

or parallel to the X axis on site.

See Addion Instrucons on page 13 Grade Match Tracking

Instrucons using the LR720T Tracking Millimetre Receiver.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere RedBack Lasers Laser-Nivelliergerät Handbücher

RedBack Lasers

RedBack Lasers D27 Series Bedienungsanleitung

RedBack Lasers

RedBack Lasers Unilevel UNG6631 Bedienungsanleitung

RedBack Lasers

RedBack Lasers 3L360 Series Bedienungsanleitung

RedBack Lasers

RedBack Lasers Unilevel UNL59 Bedienungsanleitung

RedBack Lasers

RedBack Lasers XLG44 Bedienungsanleitung

RedBack Lasers

RedBack Lasers AT1 Bedienungsanleitung

RedBack Lasers

RedBack Lasers ARL516G Bedienungsanleitung

RedBack Lasers

RedBack Lasers EL614 Bedienungsanleitung

RedBack Lasers

RedBack Lasers 3D3XR Bedienungsanleitung

RedBack Lasers

RedBack Lasers PRO5 Bedienungsanleitung

RedBack Lasers

RedBack Lasers LSR Series Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung