Reely Lightboard QC06 Bedienungsanleitung
Lightboard „QC06“
Item no.: 20 98 75
Version 07/11
2
Table of Contents
Page
1. Introduction ..................................................................................................................... 3
2. Intended Use ..................................................................................................................4
3. Scope of Delivery ............................................................................................................ 4
4. Explanation of Symbols .................................................................................................. 4
5. Product Description ........................................................................................................ 5
6. Safety Information ........................................................................................................... 6
a) General Information ................................................................................................. 6
b) Before Operation ..................................................................................................... 7
c) During Operation ..................................................................................................... 7
7. Notes on Batteries and Rechargeable Batteries ............................................................ 8
8. Connection Contacts and Displays ............................................................................... 10
9. Connection Options ...................................................................................................... 11
a) Power Supply ......................................................................................................... 11
b) Connecting the Power LEDs ................................................................................. 12
c) Connecting the LED Strips/LEDs .......................................................................... 13
d) Servo Connection .................................................................................................. 15
e) Interface Connection .............................................................................................. 16
10. Operation of the Lightboard .......................................................................................... 18
a) General Information ............................................................................................... 18
b) Selecting the Light Mode ....................................................................................... 22
c) Selecting the RC Input ........................................................................................... 23
d) Buzzer Configuration ............................................................................................. 24
11. PC Connection .............................................................................................................. 25
12. Maintenance and Care ................................................................................................. 26
13. Disposal ........................................................................................................................ 26
a) General Information ............................................................................................... 26
b) Batteries and Rechargeable Batteries ................................................................... 26
14. Technical Data .............................................................................................................. 27
3
1. Introduction
Dear Customer,
Thank you for purchasing this product.
This product complies with the statutory national and European requirements.
To maintain this status and to ensure safe operation, you as the user must observe these operating
instructions!
These operating instructions are part of this product. They contain important
notes on commissioning and handling. Also consider this if you pass on the
product to any third party.
Therefore, retain these operating instructions for reference!
All company names and product names are trademarks of their respective owners. All rights
reserved.
If there are any technical questions, contact:
Tel. no.: +49 9604 / 40 88 80
Fax. no.: +49 9604 / 40 88 48
E-mail: [email protected]
Mon. to Thur. 8.00am to 4.30pm
Fri. 8.00am to 2.00pm
4
2. Intended Use
The “QC06” lightboard is solely designed for private use in the model construction area and the
operating times associated with it.
The product must not become damp or wet. The electronics are designed for use at an operating
temperature from 0 °C to +40 °C.
This product is not suitable for other types of use. Any other use may damage the product,
causing dangers such as short-circuit, fire, electric shock, etc. Observe the safety instructions
under all circumstances!
Observe all safety information in these operating instructions. They contain important
information on handling of the product.
You are solely responsible for the safe operation of the model with lightboard!
3. Scope of Delivery
• Lightboard “QC06”
• Interface foil cable
• Operating instructions
4. Explanation of Symbols
The symbol with the exclamation mark points out particular dangers associated with
handling, function or operation.
The “arrow” symbol indicates special advice and operating information.
5
5. Product Description
The electronics are not protected from moisture and other environmental influences
and must only be used inside the model. The in- and outputs have common plug
contacts or soldering contacts.
The “QC06” lightboard is an electronics PCB ready for operation that enables different functions
in a model.
1. Control of up to 6 super-light Power-LEDs
The lightboard has two switchable outputs with active power control; 1 - 3 super-light power
LEDs can be connected to each of them.
2. Control of light effects and displays
The lightboard has 8 LED-outputs that can be connected either to individual LEDs with the
required input resistor or 12 V-LED-strips. The LEDs or LED-strops can be used as running
lights, flashlight or to display operating conditions of the “QuadroCopter”. Channel 5-8 or an
external PPM signal can be used to switch the respective light patterns. Abuzzer is available for
acoustic output of warning signals.
3. Servo connection
Up to 4 servos (channels 5 - 8) can be connected to the lightboard and are then directly controlled
by the main control of the “QuadroCopter”.
6
6. Safety Information
In case of damage caused by non-compliance with these operating instructions,
the warranty/guarantee will expire. We do not assume any liability for
consequential damage!
We do not assume any liability for damage to property or personal injury caused
by improper use or the failure to observe the safety instructions! In such cases
the warranty/guarantee will expire.
Dear Customer,
this safety information serves not only to protect the product, but also your own safety
and the safety of other persons. Therefore, read this chapter very carefully before
taking the product into operation!
a) General Information
Caution, important note!
Operating the model may cause damage to property and/or individuals. Therefore,
make sure that you are sufficiently insured when using the model, e.g. by taking out
private liability insurance. If you already have private liability insurance, verify whether
or not operation of the model is covered by your insurance before commissioning
your model.
• The unauthorized conversion and/or modification of the product is prohibited for safety and
approval reasons (CE).
• This product is not a toy and not suitable for children under 14 years of age.
• The product must not become damp or wet. The electronics are designed for use at an operating
temperature from 0 °C to +40 °C.
• If you do not have sufficient knowledge yet of how to operate remote-controlled models and
RC systems, please contact an experienced model sportsman or a model construction club.
• Do not leave packaging material unattended. It may become a dangerous toy for children.
• Should any questions arise that are not answered with the help of these operating instructions,
contact our Technical Advisory Service (for contact information see chapter 1) or another
expert.
7
b) Before Operation
• Make sure that no other models are operated on the same channel (transmitter frequency)
within the range of the remote control. Otherwise, you will lose control of the remote-controlled
models! Always use different channels if you wish to operate two or several models in direct
proximity of each other simultaneously.
• Always switch on the transmitter first and then connect the model’s drive battery at once.
• Check the functional reliability of your model and of the remote control system. Watch out for
any visible damage such as defective plug connections, loose screws or damaged cables.
• Charge the drive battery, which is necessary for operation, as well as the rechargeable battery
needed in the remote control according the instructions indicated by the manufacturer.
• When connecting LEDs, servos or connection lines, ensure secure contact. Loose or loosened
plug connections may cause interferences leading to loss of the model.
c) During Operation
• Do not take any risks when operating the product! Your own safety and that of your environment
is solely down to you being responsible when dealing with the model.
• Improper operation may cause serious injury and property damage! Therefore make sure to
keep a sufficiently safe distance to persons, animals or objects during operation.
• Fly your model only if your ability to respond is unrestricted. The influence of tiredness, alcohol
or medication can cause incorrect responses.
• Never switch off the remote control (transmitter) while the model is in use.After landing, always
disconnect the drive battery from the model first. It is only after this that the remote control may
be turned off. Never switch off the transmitter during operation.
• Never expose your model or the remote control to direct sunlight or excessive heat for an
extended period of time.
8
7. Notes on Batteries and Rechargeable Batteries
Despite the fact that handling batteries and rechargeable batteries in daily life
nowadays is a matter of fact, there are still numerous dangers and problems involved.
For LiPo/Lion rechargeable batteries in particular, various regulations must be
observed under any circumstances due to their high energy content (in comparison
to conventional NiCd or NiMH rechargeable batteries), because otherwise there is
danger of explosion and fire.
Ensure that you observe the following information and safety measures when handling
batteries and rechargeable batteries.
• Keep batteries/rechargeable batteries out of the reach of children.
• Do not leave any batteries/rechargeable batteries lying around openly. There is a risk of batteries
being swallowed by children or pets. In this case, see a doctor immediately!
• Batteries/rechargeable batteries must never be short-circuited, disassembled or thrown into
fire. There is a danger of explosion!
• Leaking or damaged batteries/rechargeable batteries can cause chemical burns to skin. Wear
suitable protective gloves when handling them.
• Do not recharge normal batteries. There is a risk of fire and explosion!
Only charge rechargeable batteries intended for this purpose. Use suitable battery chargers.
Non-rechargeable batteries (rated voltage 1.5 V) are meant to be used once only and must be
disposed of when empty.
• Always observe correct polarity (plus/+ and minus/-) of a battery pack when connecting the
rechargeable battery.
Wrong polarity may not only damage the flight model and the rechargeable batteries. There
also is a risk of fire and explosion.
• Never charge the enclosed drive battery immediately after use. Always leave the drive battery
to cool off first (at least 10 - 15 minutes).
• Only charge intact and undamaged batteries.
If the external insulation of the LiPo battery is damaged or if the rechargeable battery is deformed
or bloated, it must not be charged. In this case there is serious danger of fire and explosion!
• Never damage the outer cover of a drive battery, do not cut the foil cover, and do not prick the
LiPo battery with sharp objects. There is a risk of fire and explosion!
9
• Always remove the drive battery that is to be charged from the model and place it on a fire-
proof support. Keep distance to flammable objects and never cover the rechargeable battery
or the charger.
• Never charge rechargeable batteries without supervision and only use chargers suitable for
the battery.
• Disconnect the batteries from the charger when they are fully charged.
10
8. Connection Contacts and Displays
The lightboard has the following connection contacts or
jumper plugs:
PAD1: Plus solder connection
for supply voltage (+)
PAD2: Minus solder connection
for supply voltage (-)
PAD6: Plus solder connection
for power LED output L2
PAD7: Minus solder connection
for power LED output L2
PAD9: Plus solder connection
for power LED output L1
PAD10: Minus solder connection
for power LED output L1
X1: Jumper for buzzer
X2: Jumper for light mode
X3: Connection contacts
for LED or LED-strips 1 - 4
X4: Connection contacts
for LED or LED-strips 5 - 8
X5: Connection contacts for servo 1 (channel 5)
X6: Connection contacts for servo 2 (channel 6)
X7: Connection contacts for servo 3 (channel 7)
X8: Connection contacts for servo 4 (channel 8)
X9: Connection contacts for an external RC input signal
X10: Connection strip for the broad interface cable
X11: Jumper for the interface selection
X12: Serial interface
X13: Control connection for lines SA1, SA2 and Status
SW1: Jumper for the RC input selection
SW2: Reset button
BUZ1: Buzzer
For a detailed description of the different
contacts and the connection options, see the
following sections.
Figure 1
SW1
R2
T4
PAD1
CB4
C4
R21
X8 X7
X9
IC2
X6
X5
T5 T2 T3
Q1
X4 X3
C3
C2
X10
C16
C11
C10
C9
C8
C13
C12
C15
C14
IC1
R1
X2
SW2
BUZ1
R3
R6
R7
X1
+
X11 X12
R2
T4 T5 T2 T3
Q1
X10
C16
C11
C10
C9
C8
C13
C12
C15
C14
R23
+
-
L2
+
-
L1
CB3
PAD6
PAD7 PAD10 PAD9
R22
PAD2
-
IC3
IC4
L2
L1
X13
C1
Inhaltsverzeichnis
Andere Reely Drohnen- und Quadcopter-Zubehör Handbücher
