Reer 5006 SCOPI Bedienungsanleitung

reer 5006 SCOPI

User Manual

Introduction

The User Manual for this unit consists of two parts. The first part contains a Quick Start

Manual for use as a baby monitor; the second part informs about advanced functions

as normal PMR 446 transceiver for you or your children to enjoy at a later stage. Here

you also find the Safety Precautions and other legally binding information.

Prepare Radio As Baby Monitor System

Your reer 5006 Scopi comes in a two-pack. In default setting both units are equal

portable transceivers, working according to the European standard PMR 446 for free

use. Select one unit as baby unit, the other as parent unit before using the radios as

baby monitors.

Location Of Controls

ntenna

PTT button External

connections

Search +

Keypad lock

On/Off

Out-of-range

function

Select functions:

Menu button

Select down

Select up

Display and Icons

Icons and Terms

RX Reception: listen via the speaker

TX Transmission: PTT button is pressed or unit transmits in VOX

mode

SCAN Auto scan: unit scans channels one by one

VOX Active VOX mode: unit transmits automatically (without pressing

PTT) when detecting sounds

Key tones are activated

Out-of-range function is activated (automatically AU, manually Pb,

or both)

Keypad lock is activated

Roger beep (short beep after transmission) is activated (only in

PMR 446 transceiver mode)

Battery level indicator: 3 bars = full, 1 bar = nearly exhausted

(check during or right after transmission!)

Baby icon: displays in babysitter mode on both baby and

parent units. No display in PMR 446 transceiver mode.

Chapter 1: Baby Monitor Function

Prepare Unit – Insert Battery

Remove the belt clip (pull spring and remove to top)

and open the battery compartment.

Insert a supplied battery pack in each unit (packed

separately).

The arrow on the battery pack indicates the direction

in which to insert:

The arrow shows up and the print must be

legible after insertion, as shown in the figure).

Connect one of the power adaptors with the base

station and connect to a 230V wall outlet.

Charge the unit for several hours (new batteries are

only partly charged ex factory).

Note: Never open or dismantle the supplied battery

pack!

Alternatively, insert commercially available AAA alkaline

batteries (4 units) or 4 individual rechargeable Ni-MH

batteries.

DO NOT charge alkaline batteries, never place the

transceiver in the charger when using batteries. Do

not mix rechargeable and normal batteries!

Observe the polarity as printed inside the battery

compartment.

Prepare As Baby Monitor

It only takes one simple programming step after inserting and charging the battery

pack to determine which unit will serve as the baby unit and which one as the parent

unit.

• Turn one unit on (press the On/Off button for 3 sec).

• Press the MENU button twice.

The display shows the baby icon and OF.

• Press on the baby unit to select b(on the other unit select P(=

parents).

• Briefly press the PTT button to confirm, or simply wait a few seconds.

The babysitter setup is completed.

Now the display shows the baby or parent channel top left, such as b1 and the baby icon 

bottom center.

This setting already includes the highest sensitivity setting for the baby unit, automatic

out-of-range control between baby and parent unit, the possibility to test the range and to talk to

the baby.

What Else Can Be Set?

Volume

• Press to set the volume.

The display shows the volume setting in steps between LE 00 and LE 09.

The volume setting is important in case you want to talk to the baby. Set the volume level to LE

00 to mute the baby unit at all times.

Set the volume level for the parent unit to the desired level.

Display Alarm

The parent unit with muted speaker (set to LE 00) still lights up to show that the baby unit is

communicating.

• The display backlight turns on for approximately 5 seconds with every alarm.

Channel Number

The channel number must be the same for both units.

There are 9 possible settings, for the baby unit b 1 to b 9 and for the parent unit P 1 to P9.

1 to 9 stands for channel combinations programmed ex factory between PMR 446 radio

channels and CTCSS encoding. The numbers are only valid for this type of transceiver and

there is no communication with other baby monitors!

Set Channel

• Briefly press the MENU button once. The set channel will flash.

• Press to select a different setting.

• Press the PTT button to confirm or simply wait a few seconds.

Set Baby Monitor Sensitivity

You can set the sensitivity of the baby unit in 4 levels.

With initial installation the unit is set to level 4

• Briefly press the MENU button three times to access the VOX menu.

The display shows the sensitivity setting as a number on the right (between 1and 4).

Press to select a level between 1and 4.

1setting for highest distance from the baby cot

2medium sensitivity setting

3low sensitivity setting

4 highest sensitivity setting (default setting) with additional talkback function

We recommend level 4 as start position. If your baby cries for a longer period without

breaks you may want to talk to your baby to calm it down. For this set the baby unit to

level 4 to allow you after 20 seconds of transmission to talk back for 10 seconds.

• Use these 10 seconds to talk to your baby and calm it down.

• Simply press the PTT button on the parent unit and talk to your baby.

As long as your baby is quiet you can speak from the parent unit at any time (if the

volume on the baby unit is not set to 00).

Automatic Out-Of-Range Function

The automatic out-of-range function is automatically activated in babysitter mode and

needs no further settings!

The automatic out-of-range function automatically checks every 60 seconds if baby

and parent units are communicating. The parent unit sends a “search pulse”, which is

answered by the baby unit. In case there is no reply for more than 2 minutes, then both

units are no longer communicating. This can be due to a dead spot, the batteries of the

other unit being exhausted or the unit being turned off.

During communication the icon is constantly displayed. The icon flashes in case

the communication is interrupted and the event is optically displayed on the parent unit

as OU and 5 beep tones are audible.

After 2 minutes the icon is again constantly displayed if a unit changes the location and

is again within the range of the other unit.

The out-of-range function can also be deactivated.

• Press the MENU button four times.

The display shows, depending on the previous setting, AU,Pb or OF.

• Press to select:

Pb out of range function on request (=Press button)

AU automatic function activated

OF automatic function deactivated

Manual Out-Of-Range Test

Independent of the automatic out-of-range control of the other unit you also have the

manual out-of-range test. This test is also available with the out-of-range function

deactivated on the baby unit!

On the press of a button you can determine if the other unit is within range. The automatic

control on the parent unit must be set to Pb or AU.

• Press the button and wait a few seconds. The baby unit answers your request

and the parent unit plays a melody.

External Microphone

For the baby monitor function we supply an external microphone (type BM 1). This has the

following advantages:

• It is more sensitive than the build-in microphone and it responds to a greater distance.

• It allows you to extend the distance between transceiver and baby cot – HF radiation

is greatly reduced!

• It allows you to position the radio in optimum location, such as the windowsill or high

up on a wardrobe.

Please locate the BM1 microphone in a position where the baby cannot reach it. Use the

supplied sticky pad to safely attach the microphone.

Connect the microphone to the MIC jack on the side of the baby unit. Flap the rubber cap open

and use the bottom jack.

Chapter 2: Advanced Functions and Use As PMR 446 Transceiver

By default (or after storing the radios with removed battery packs) both units are in equal

transceiver mode. They can be used for different purposes; as walkie-talkies for older children,

during hikes and trips, events, maintenance work in and around the house, where

communication is needed and for many more purposes. The communication range is up to 5

km, depending on the terrain, in open spaces with no obstructions or reduced range in the city.

Use With Default Setting And No Further Programming

• Insert the batteries (as described on page 4).

In case you are using individual AAA batteries instead of the supplied rechargeable battery

pack, please observe the correct polarity.

• Press for approx. 3 seconds to turn both units on.

• A channel number is displayed, e.g. 1or any other previously set channel

number between 1and 48.

If both units display the same channel number they are ready for use.

Press the PTT button on the left side of the unit to communicate.

PTT Button To Talk

• Press and hold the PTT button to transmit; release the button to receive.

PTT Button To Call

• Briefly press the PTT button twice in quick succession.

• The unit transmits a call melody to all other units on this channel within your

range.

Toggle Between Baby Monitor And Transceiver Modes

You can easily switch to transceiver mode in case your radios were set to baby monitor

mode:

• Turn the units on.

• Press the MENU button twice.

• bor P(according to previous setting) flashes on the display.

• Press to toggle between b, Pand OF. In transceiver mode the setting

must be OF (= baby mode OFF).

• Briefly press the PTT button or wait for 5 seconds.

Volume

• Press to set the volume.

The display shows the volume setting in steps between LE 00 and LE 09.

Select Channel

In Europe you can use one of 8 PMR 446 channels. Furthermore, you can individually set the

coding via CTCSS tones separately for channels 1 to 8 among 38 possible codes. This code is

displayed right from the channel number 1 to 8 as a smaller 2-digit number between 00 and 38.

5 I0 for example stands for channel 5 and CTCSS sub code 10.

To simplify operation with channels and sub codes the unit is preprogrammed with additional

channel combinations:

These are the channel numbers 9to 48. These are all combinations with one of the 8 permitted

PMR channels with different CTCSS codes, saving the user the trouble with codes and

channels while using the numbers 9 to 48.

You only have to take care that all communicating units are set to the same numbers

on the display.

If communicating with users of other transceiver makes only use channels 1 to 8 and set the

sub codes manually, they are following international standards.

Set Channel

• Press the MENU button once. The currently set channel flashes.

• Press to select a different setting.

• Press the PTT button to confirm or simply wait a few seconds.

Channel Scan

Briefly press the Sbutton to automatically scan all channels for activity.

• Press the button to start scanning; press again to stop scanning.

• Scanning stops after a signal is detected and you listen to the channel for 8 seconds.

Press the PTT button to stop scanning and to respond.

With no response scanning starts again.

Keypad Lock

All keys (except the PTT button and On/Off) can be locked to prevent accidentally pushing

the buttons.

Lock keypad:

• Press and hold the button for approx. 3 seconds, until the lock icon ( ) is

displayed.

• Press and hold the button again for approx. 3 seconds, until the lock icon turns off.

Backlight

The display backlight automatically comes on for 5 seconds after pressing any button.

Set CTCSS Codes

The additional CTCSS codes serve to avoid listening to other stations on the same channel.

This can even be a combination of baby and parent unit – you would not want to listen to

somebody else’s baby. It is always possible that other users are on the same channel.

Do not mistake this for safety from interception: it is always possible to intercept non-encrypted

analog radio talk; this only needs any PMR 446 transceiver or a scanner.

Andere Handbücher für 5006 SCOPI

Inhaltsverzeichnis

Andere Reer Babyphone Handbücher

Reer

Reer Cosmo 50150 Bedienungsanleitung

Reer

Reer BeeConnect Plus 50120 Bedienungsanleitung

Reer

Reer 50040 Bedienungsanleitung

Reer

Reer 50070 Bedienungsanleitung

Reer

Reer 3004 BABYPHON MIDI Bedienungsanleitung

Reer

Reer Nova Bedienungsanleitung

Reer

Reer IP BabyCam Move Bedienungsanleitung

Reer

Reer 5006 SCOPI Bedienungsanleitung

Reer

Reer BABYPHON NEO 1200 Bedienungsanleitung

Reer

Reer 5006 SCOPI Bedienungsanleitung

Reer

Reer Baby Cam L Bedienungsanleitung

Reer

Reer BABYPHON AURIGA Bedienungsanleitung

Reer

Reer Babyphone Rigi 400 Bedienungsanleitung

Reer

Reer Baby Cam Bedienungsanleitung

Reer

Reer 50080 Bedienungsanleitung

Reer

Reer Apollo Bedienungsanleitung

Reer

Reer 8006 Bedienungsanleitung

Reer

Reer Rigi Digital Bedienungsanleitung

Reer

Reer 5006 SCOPI Bedienungsanleitung

Reer

Reer BabyCam XL Bedienungsanleitung

Reer

Reer 5006 SCOPI Bedienungsanleitung

Reer

Reer 50010 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Philips

Philips SCD 469 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

Philips

Philips AVENT SCD841 Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

Graco

Graco iMonitor 2797 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Philips

Philips SBC SC364 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung