Reflex Safari Bedienungsanleitung
FOLDING BIKE BASIC ASSEMBLY GUIDE
WARNINGS
KEY BIKE PARTS
BEFORE YOU START
THE FRAME
THE HANDLEBAR
CONTENTS
WARNINGS
IF IN DOUBT - CONSULT A QUALIFIED BICYCLE MECHANIC
OR CALL OUR CUSTOMER HELPLINE ON 0161 727 0139
....................................................page 2
.............................................page 3
.......................................page 4
...................................................page 5
..........................................page 6
THE SADDLE
THE PEDALS
REFLECTORS AND BELL
FINAL CHECKS
..................................................page 7
...................................................page 8
.................................page 9
.............................................page 10
Always check that brakes work before each use - failure to set brakes correctly may result in serious injury or even death.
Ensure all nuts / bolts / screws are securely ghtened and checked before use. Recommended torques (ghtness levels) are
available in the owners manual.
Check bike regularly for signs of damage. Do not use again unl repaired.
Keep your bike in good condion by cleaning off dirt, keeping it well maintained and storing in a dry place.
Always wear a helmet that meets the latest safety standards and make sure you follow the manufaterer’s instrucons.
2
KEY BIKE PARTS
SADDLE
FRAME
BRAKE LEVERS
FRONT REFLECTOR
HANDLEBAR
HANDLEBAR STEM
FRONT BRAKE
& CABLE
FORK
WHEEL REFLECTORS FRONT WHEEL
PEDALS
BACK WHEEL
REAR REFLECTOR
3
BEFORE YOU START
CARDBOARD CABLE TIES PLASTIC SAFETY CAPS
(on front wheel &
handlebar stem)
Remove all packaging. Take care not to scratch any paintwork.
Please note - The plasc caps may have fallen off in transit if they are not on the bike.
4
THE FRAME
ASwing the front of the frame round to meet the
back of the frame
To join the folding mechanism you need to push
the quick release lever up as shown and join the
frame together.
i
ii
BSwing the quick release arm anti-clockwise into the
folding bracket
Close the quick release lever as shown, ensuring it
folds up in a vertical direction.
i
ii
5
BSwing the quick release arm up into the folding
bracket
Close the quick release lever as shown, ensuring it
folds down towards the rear of the bike
i
ii
6
THE HANDLEBAR
ASwing up into an upright position
To join the folding mechanism you need to push
the quick release lever to the left, and join the
handlebar stem together
i
ii
Ensuring the quick release lever is in the open position as shown, slide the saddle into the frame. Make sure you
insert the saddle beyond the minimum insertion mark.
Once the saddle is at your desired height, close the quick release lever as shown
Note: Sometimes the saddle may come inserted in the frame facing backwards, if so release the quick release and turn,
before closing quick release again.
i
ii
THE SADDLE
MINIMUM
INSERTION
MARK
7
Yor folding bike comes with a folding pedal on the right side (chain side) of
the bike. To open this, bring the pedal to a horizontal position, 90 degrees to
the pedal arm.
Keeping the pedal in this position, push it towards the pedal arm until you
hear a click
i
ii
THE PEDALS
Unfolding the pedals
Press the release buttons on either side of the pedal. Whilst holding pull the pedal
away from the pedal arm. It will now fold down easily.
Unfolding the pedals
8
AFirst fully release the securing screws as shown
(an-clockwise)
COnce these are in place, replace the screws and ghten by turning clockwise using a cross-head screwdriver
BWrap the bell around the handlebar as shown, remembering
to put it in a place where you can reach it easily whilst riding.
Then wrap the white reflector around the handlebar near the
centre, and wrap the red reflector in the same way around
the saddle post.
BELL RED REFLECTOR WHITE REFLECTOR HANDLEBAR
(Bell and White Reflector)
SADDLE
(Red Reflector)
9
REFLECTORS AND BELL
A
C
D
IMPORTANT: ENSURE ALL NUTS / BOLTS / SCREWS ARE TIGHT
RECOMMENDED TORQUES IN OWNER’S MANUAL APPENDIX
IF IN DOUBT PLEASE CONSULT A QUALIFIED BICYCLE MECHANIC.
PLEASE READ OWNER’S MANUAL BEFORE RIDING THIS BIKE
ALWAYS CHECK BRAKE FUNCTIONALITY BEFORE RIDING
You can now ensure your saddle and handlebars are at a comfortable riding position, and fully tighten. Always be
aware of the minimum insertion mark and make sure these are inserted beyond this point.
This assembly guide is copyrighted to Avocet Sports Limited. Any reproducon, in whole or in part, is strictly forbidden without prior wrien consent.
Check that all bolts and xings are tight and secure. You should do this before every ride.
BCheck tyre pressures regularly. Recommended tyre pressures are clearly marked on the side of the tyre.
Check functionality of brakes before every ride, you will nd out more about this in the user manual included.
10
FINAL CHECKS
Andere Reflex Fahrrad Handbücher
