Regency THE INDOOR/OUTDOOR FAN Bedienungsanleitung

•I/O “THE INDOOR/OUTDOOR FAN”•

•

CEILING FAN OWNER’SMANUAL

•

WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.

5/03

GENERAL INSTALLATION & OPERATION INSTRUCTIONS

1. T

2. T

.All electrical

connections must be made in accordance with local codes, ordinances and/or the National Electric Code. If you are

unfamiliar with the methods of installing electrical wiring and products, secure the services of a qualified and

licensed electrician as well as someone who can check the strength of the supportive ceiling members and make

the proper installation(s) and connections.

3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades

should be at least 7 feet from floor when fan is operating.

4. The fan should be mounted on a ceiling outlet box, an approved box UL listed as “

“s

t” is

required. The box and its supporting members must be able to support the moving weight of the fan (at least

35lbs.). The box must not be able to twist or work loose. Installation on a concrete ceiling should be performed

by qualified personnel.

5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the

carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure

that you do not mix fan blade sets, as each blade is part of a weighted set.

6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into

outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one

side of the outlet box, and the “HOT” wires on the other side.

7. Electrical diagrams are for reference only.

8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling

and/or causing damage or injury.

9. The fan can be made to work immediately after installation - the bearings are adequately charged with grease so

that, under normal conditions, further lubrication should not be necessary for the life of the fan.

10. The fan should be turned off and allowed to stop rotating before reversing fan direction.

* To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support”

and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of

lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician

if in doubt.

* To reduce the risk of fire, electrical shock, or personal injury, only use this fan with an appropriate speed control

device designed for use with this ceiling fan.

* To reduce the risk of personal injury, do not bend the blade arms when installing or balancing the blades or cleaning

the fan. Do not insert any objects between rotating fan blades.

)

TOOLS AND MATERIALS REQUIRED

Thank you for choosing a Regency Ceiling Fan.

You have chosen the best!

Your new ceiling fan has been designed to provide

many years of service and enjoyment.

• Phillips screwdriver

• Blade screwdriver

• Wrench or pliers

• Wire cutter

• Stepladder

• Wiring supplies as required by

electrical code

IMPORTANT SAFETY PRECAUTIONS

1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary,

the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its

side, or the decorative housing may shift, be bent or damaged.

2. Examine all parts. You should have the following:

UNPACKING YOUR FAN

1. Mounting bracket

2. Ceiling canopy

3. Downrod/ball assembly

4. Fan housing with motor and blade arms

5. Shade

6. Fan blades (5)

7. Bracket hardware (wood screws, washers,

wire nuts)

REV

MED

OFF

LOW

8. Blade arm to blade screws w/washers

9. Downrod pin and cotter pin

10. Remote control transmitter and receiver w/wall holster

11. Light bulb (100W “J” type)

Recommended for uplight:

Four candelabra base (E12) 40W bulbs (not included)

Verify that you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from

packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Do not

lay fan on its side as this could result in shifting of motor in decorative enclosure.

:To avoid possible electrical shock, be sure elec-

tricity is turned off at the main power box before wiring. All

wiring must be in accordance with National and Local

Electrical Codes and the ceiling fan must be grounded as a

precaution against possible electric shock.

1. Locate ceiling area where fan is to be mounted, being sure

location agrees with the requirements in the minimum

clearance section of this guide. Mounting area must be

sound and of adequate size to support 35 lbs. (p. 1, #3

and #4)

2. If not already present, mount a UL listed outlet box

marked “suitable for fan support” following the instruc-

tions provided with the outlet box. The outlet box must

be able to support a minimum of 35 pounds.

3. Attach hanger bracket to outlet box using screws pro-

vided with the outlet box.

PREPARATION

Ceiling Fan 

Outlet Box

Hanger

Bracket

Outlet Box

Screw

Flat Washer

Spring Washer

Parts identification on assembled fan

INSTALLING THE MOUNTING BRACKET

Downrod

Canopy

Fan Housing

Blade

Blade Arm

Glass Shade

ASSEMBLY INSTRUCTIONS: DOWNROD AND CANOPY

1. Carefully support fan housing (motor) in its styrofoam packing with the mounting collar (where the wires come

out) facing upward.

2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin;

remove ball.

3. Feed the wires from top of fan through the end of the downrod, and set end of downrod into mounting collar so

the hole in the downrod lines up with the hole in the side of the mounting collar.

4. Insert downrod pin through holes in mounting collar and downrod and insert cotter pin to secure downrod.

5. Tighten security screw against downrod using a large flat blade screwdriver to ensure a tight fit against downrod.

Tighten lock nut to mounting collar.

NOTE: Fan has 6 feet of hook-up wire in case you

are using a long extension downrod. Wires can be

cut so only 8 inches or so extend beyond the top

of the downrod to make the electrical connections

easier and safer.

6. Feed wires through canopy and slide

canopy over downrod to lay on top of fan.

It will be attached to ceiling later.

7. Feed wires through ball and slide ball over

downrod, past hole in the top end of downrod.

Insert ball pin (removed in Step 2), slide ball

up and tighten set screw to secure ball in

place.

8. Install 4 candelabra base bulbs (E12, 40w

max) in top sockets.

Ground

Wire

Hook-up Wires (5)

Ball

Security Screw and Lock Nut

Mounting Collar

Downrod Pin

Fan

Housing

Canopy

Downrod

(Optional extension shown)

40W Candelabra

Base Bulbs

Cotter Pin

INSTALLING THE FAN

:To avoid damaging the blade arms and blades, do not install blades onto fan until fan is fastened to ceiling.

If arms are bent or misaligned, excessive wobble may occur.

1. Lift ball/downrod/fan into hanger bracket opening. NOTE: The tab opposite hanger bracket opening should fit in

slot on ball.

2. Install remote control receiver (with codes set) and make wire connections, (refer to sections titled “Remote

Control” and “Electrical Connections”).

3. Slide canopy up and fasten to hanger bracket with screws provided.

Hanger

bracket

tab

Ball

Ball slot

REMOTE CONTROL

Multiple code choices are included with your fan’s remote control in case:

• you have more than one remote control fan and want them to respond only to their own remote control

• you have other radio controlled devices in your home that may interfere with the fan remote control (i.e. garage

door opener)

• you experience radio interference on a chosen frequency (code setting)

This unit has 16 different code combinations. To set the code, perform these steps:

1. Setting the code on the TRANSMITTER [Fig. 1]:

a. Remove battery cover.

b. Slide code switches to your choice of ON or OFF position. Use a small screwdriver or ball point pen to slide

each switch firmly up or down.

c. Install 9v battery (not included).

d. Replace battery cover on transmitter.

2. Setting the code on the RECEIVER [Fig. 2]:

a. Locate the code switches on the bottom of the remote receiver.

b. Slide code switches to the SAME POSITIONS as set on your transmitter.

After codes are set, install the receiver

in the space above the ball in the

hanger bracket [Fig. 3]. Be careful not

to pinch any of the receiver’s wires.

1234

Code

Switches

TRANSMITTER

ON ECE

Code

Switches

RECEIVER

1234

ON DIP

Antenna

Fig. 1 Fig. 2

Hanger

bracket

Ball

Receiver

Fig. 3

Be sure electricity is turned off at the main power box before wiring.*

Four wires are connected to the fan (plus the ground wire).

Black - the “hot” power to run fan.

White - the “common” power to run fan and light,

also referred to as “AC neutral”.

Blue - the “hot” power for lower light.

Gray - the “hot” power for upper light.

Green - ground wire.

Six wires are connected to the remote control receiver. Four

will connect to the four wires coming out of the fan

(matching color to color) and the remaining black wire and

white wire will connect to the building 110v AC circuit.

BE SURE ELECTRICITY IS TURNED OFF AT THE

MAIN POWER BOX BEFORE WIRING.

Connect six power wires as shown [Fig. 1], using wire nuts

provided. Connect green ground wires to building ground

wire circuit. Extend antenna wire inside canopy, but do not

attach to any other wire.

NOTE: If power to the fan’s electrical ceiling box is controlled by a wall switch, the wall switch must remain ON

for the radio remote control to operate. Turning the wall switch OFF will turn off all fan/light function and resets

the receiver back to default mode. The wall switch will need to be turned back ON to allow use of remote control.

* Restore power by replacing fuse or resetting circuit breaker ONLY AFTER ALL INSTALLATION AND ELECTRICAL

WORK IS COMPLETED AND DOUBLE-CHECKED.

1. Place washer on screw. Insert this assembly through the

blade and start the screw into the blade arm. Repeat this

procedure without tightening the screw until all 3 screws

have been started into the blade arm (Fig. 2).

2. Tighten each screw, starting with center screw.

ELECTRICAL CONNECTIONS

Screw

Washer

Blade Arm

Blade

Receiver

Antenna

110v(BLACK)

MMON(WHITE)

BLADE ATTACHMENT

Fig. 1

Fig. 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Lüfter Handbücher

Regency

Regency TROPIC AIR Series Bedienungsanleitung

Regency

Regency LX Series Bedienungsanleitung

Regency

Regency INDY Bedienungsanleitung

Regency

Regency Celsius Bedienungsanleitung

Regency

Regency Quatro Bedienungsanleitung

Regency

Regency BIMINI Bedienungsanleitung

Regency

Regency Cayman Bedienungsanleitung

Regency

Regency MX Excel Bedienungsanleitung

Regency

Regency GLADIATOR GL3 Bedienungsanleitung

Regency

Regency Cabana Bedienungsanleitung

Regency

Regency OASIS Bedienungsanleitung

Regency

Regency PFLK10 Bedienungsanleitung

Regency

Regency Deuce Hugger Bedienungsanleitung

Regency

Regency Cayman Bedienungsanleitung

Regency

Regency VERA CRUZ Bedienungsanleitung

Regency

Regency Regatta Bedienungsanleitung

Regency

Regency Artiste Bedienungsanleitung

Regency

Regency BIMINI Bedienungsanleitung

Regency

Regency GRAND MARQUIS Bedienungsanleitung

Regency

Regency FE-45A Bedienungsanleitung

Regency

Regency ANDROS Bedienungsanleitung

Regency

Regency Marquis Series, Countess Series Bedienungsanleitung

Regency

Regency NOLA Bedienungsanleitung

Regency

Regency Vantage Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung