Regency City Series CB40E Series Datenblatt

City Series CB40E Gas Fireplace

Model CB40E-NG CB40E-LP

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)

Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62 kPa)

Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)

Orice Size -Altitude 0-4500 ft. #42 DMS #53 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

15,500 BTU/h

(4.54 kW)

15,500 BTU/h

(4.54 kW)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

28,500 BTU/h

(8.33 kW)

28,500 BTU/h

(8.33 kW)

Vent Sizing 4” Inner / 6-5/8” Outer 4” Inner / 6-5/8” Outer

48 7

16 "

1231mm

16"

648mm

37 3

949mm

43"

1091mm

33 7

16 "

849mm

183mm

Ø4"

102mm

Ø 6 3

171mm

11 7

16 "

291mm

24 1

616mm

49 5

1261mm

18 11

16 "

475mm

17 11

16 "

449mm

34 5

879mm

10 1

267mm

15 1

16 "

382mm

39 5

1007mm

200mm

CB40E Gas Fireplace

Caution Requirements

The top, back and sides of the replace are dened by

stando󰀨s. The metal ends of the stando󰀨 may NOT be

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this replace and vent

system be installed only in accordance with these instructions.

CLEARANCES CB40E (3 SIDED)

Clearance: 3 sided Dimension Measured From:

A: From Floor 25-9/16" (649mm) Top of Fireplace Opening

A�� : Mantel Height (min.) ** Top of Fireplace Opening

B: Sidewall (on one side) 8-1/2" (216mm) Side of Fireplace Opening

C: Enclosure Width (min.) 48-7/16" (1230mm) Minimum inside dimensions

D: Mantel Depth (max.) **

E: Alcove Width 84" (2134mm) Side wall to side wall (min.)

F: Alcove Depth 36" (914mm) Front of Unit

G: To Enclosure Ceiling (min/max) 0-3" (76mm) From top of enclosure

H: Convection Air outlet 120 sq. inches (min) * Top/front or side of enclosure

I: Enclosure Depth (min.) 19" (483mm) Minimum inside dimensions

J: Opening Height 15-1/16" (383mm) Bottom/Top of Fireplace Opening

K: To Ceiling (min) All 3 sides 1-1/2" To Top of Ceiling

L: Chase Enclosure (min.) 63" (1600mm) From base of unit/oor

Hearth 0" No hearth required

** See mantel clearances chart in this manual

Flue Clearances to Combustibles

Horizontal - Top 3"

Horiztonal - Side 2"

Horiztonal - Bottom 2"

Vertical 2"

Passing through wall/

floor/ceiling - when

restop is used.

1-1/2"

* A minimum of 120 square inches of open area, not lower than 3" from top of enclosure, required for all

installations — this can be achieved by having an open area in front, each side, and/or above as shown

in the four diagrams on the next page.

The HeatWave Duct Kit has

different clearance and framing

requirements, check the HeatWave

manual for details.

Alcove

CB40E Gas Fireplace

CLEARANCES CB40E (3 SIDED)

Floor to ceiling with top opening Low framing with vents in front/sides or top

Full framing with low vents in front or sides Full framing with vents in front or sides

CB40E Gas Fireplace

FRAMING DIMENSIONS CB40E (3 SIDED)

NOTE: Framing may be constructed of combustible material (ie. 2x4) and does not require steel studs. Two (2) optional steel stud kits may also be purchased.

These kits may be used in place of the conventional wood framing as shown below. It comes as a compact kit (ﬂush to the appliance on all sides)or

an extended kit. The extended kit protrudes beyond each side of the appliance as shown on the front cover of this manual. There is also an optional

hearth kit which may be purchased as shown on the front cover of this manual. These kits are highly recommended as it was designed speciﬁcally

for the product to facilitate ease of installation. See instructions in this manual for details.

Framing

Dimensions Description CB40E

A Framing Height 37-3/8” (949mm)

B Framing Width 48-1/2" (1232mm)

C Framing Depth 19" (483mm)

D Minimum Height to Combustibles 63"(1600mm)

G Vent Centerline Height 56-1/4" (1429mm)

IGas Connection Opening Height 2" (51mm)

JGas Connection Height 4 " (106mm)

K Gas Connection Inset 13" (330mm)

LGas Connection Opening Width 3-1/2" (89mm)

Note: A combined minimum of 120 square inches of open area is required for the convection air outlet to cool the enclosure. Ensure clearances for

Convection Air Outlets are met. See clearances CB40E (3 sided) in this manual as there are di󰀨erent methods as to how this can be achieved.

Note: Only basic framing dimensions are shown. The framing may also extend beyond the appliance on either side and also extend out front if a hearth is

desired. See clearance/nishing requirements for details

Note: This appliance must be installed on

a solid surface such as a plywood oor

which must be the full width and depth of

the appliance.

CB40E Gas Fireplace

MANTEL CLEARANCES CB40E (3 SIDED)

Due to the extreme heat this replace emits, the

mantel clearances are critical. Combustible mantel

clearances from top of front facing are shown in the

diagram on the right.

Note: Ensure the paint that is used on the mantel

and the facing is "high quality" or the paint

may discolour.

MANTEL LEG CLEARANCES

Combustible mantel leg clearances as per diagram:

Combustible Material

212 6 4810

Standoff

Wood Stud

(On Edge)

9”

15-1/16”

Top of

Fireplace

Opening

12" (305mm)

Drywall, wood, wood panel, etc.

2”

Bottom

Fireplace

Lip

12"

MANTEL LEG

8-1/2"

CB40E (3 sided)

CB40E Gas Fireplace

VENTING INTRODUCTION

The CB40E uses the "balanced ue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner

draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air

up the chimney.

Note: These ue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel

or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

VENTING ARRANGEMENT FOR HORIZONTAL TERMINATIONS

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o(two 45o elbows equal one 90oelbow).

Note: Must use optional rigid pipe adapter (Part# 510-994) when using Rigid Pipe Venting Systems)

• Maintain clearances to combustibles as listed in "Clearances" section

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever passing through a wall.

• A vent guard should be used whenever the termination is lower than the specied minimum or as per local codes.

• Flex system can only be used up to 10 feet - otherwise rigid venting must be used.

VENT RESTRICTOR SETTING:

Vent restrictor factory set at Set 0.

Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 0 to Set 2 if required.

NOTE: A minimum of 1' (305mm) vertical o󰀨 the top of the unit is required before any horizontal runs can start.

Note: For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum continuous vent

length of up to 10 feet. If longer runs are required, rigid pipe must be used.

56-1/4” (1429mm)

CB40E Gas Fireplace

HORIZONTAL TERMINATIONS

RIGID PIPE 4" X 6-5/8"

The diagrams below shows examples of horizontal termination arrangements using one, two, or three 90oelbows (two 45o elbows equal one 90oelbow)

1. A maximum of three 90oelbows are permitted.

2. Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994. when using rigid pipe vent systems.

• A vent guard should be used whenever the termination is lower than the specied minimum or as per local codes.

• Flex system can only be used up to 10 feet - otherwise rigid venting must be used.

HORIZONTAL VENTING WITH TWO (2) 90OELBOWS

One 90oelbow = Two 45oelbows.

Option V H + H1

With these options,

maximum total pipe length

is 30 feet with minimum

of 6 feet total vertical

and maximum 8 feet total

horizontal.

Please note minimum 1

foot between 90oelbows

is required.

A) 1' Min. 2' Max.

B) 2' Min. 4' Max.

C) 3' Min. 5' Max.

D) 4' Min. 6' Max.

E) 5' Min. 7' Max.

F) 6' Min. 8' Max.

Restrictor Set 0 - Factory Setting

HORIZONTAL VENTING WITH THREE (3) 90OELBOWS

One 90oelbow = Two 45oelbows.

Option V H V + V1 H + H1

With these options,

max. total pipe

length is 30 feet with

min. of 12 feet total

vertical and max. 9

feet total horizontal.

Please note min. 1

foot between 90o

elbows is required.

A) 1' Min. 1' Max. 2' Min. 2' Max.

B) 1' Min. 2' Max. 3' Min. 3' Max.

C) 2' Min. 2' Max. 5' Min. 4' Max.

D) 3' Min. 2' Max. 7' Min. 5' Max.

E) 4' Min. 3 Max. 9' Min. 6' Max.

F) 5' Min. 4' Max. 10' Min. 7' Max.

G) 6' Min. 5' Max. 11' Min. 8' Max.

H) 7' Min. 6' Max. 12' Min. 9' Max.

Restrictor Set 0 - Factory Setting

CB40E Gas Fireplace

VENTING ARRANGEMENT FOR VERTICAL TERMINATIONS

Vertical Venting with straight Vertical venting and or with a max. of two (2) 90oElbows (1 - 90o = 2 - 45o)

The shaded area in the diagram shows all allowable combinations

of straight vertical and o󰀨set to vertical terminations, using two

90oelbows, with Rigid Pipe Venting Systems.

Two 45o elbows equal to one 90oelbow.

• Vent must be supported at o󰀨sets.

• Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the

"Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever

passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994.

when using rigid pipe vent systems.

• Refer to the "Vent Restrictor Position" section for

details on how to change the vent restrictor from the

factory setting of Set 0 through to Set 3 if required.

NOTE: A minimum of 1' (305mm) vertical o󰀨 the top of

the unit is required before any horizontal runs can start.

Maximum: 37 ft. (11.2m)

Minimum

8’6” (2.6m)

Min. 56-1/4”

(1429mm)

Minimum length of pipe

between elbows 12” (305mm)

Maximum: 27 ft. (8.2m)

Vertical Height (Feet)

Horizontal (Feet)

410 12 16 18

14 2

Vent Restrictor on Set 2

Vent Restrictor on Set 3

Vent Restrictor on Set 1

CB40E Gas Fireplace

VERTICAL TERMINATIONS RIGID PIPE 4" X 6-5/8"

• Two 45o elbows equal to one 90oelbow. Maximum of six 45o elbows allowed, not including the starting 45o elbow at the ue collar.

• Vent must be supported at o󰀨sets.

• Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994. when using rigid pipe vent systems)

Vertical Venting with Three (3) 90oElbows

One 90oelbow = Two 45oelbows.

H1 H

Option V H + H1 V + V1

With these options,

max. total pipe length

is 30 feet with min. of

10 feet total vertical

and max. 8 feet total

horizontal.

Please note min. 1

foot between 90o

elbows is required.

A) 1' Min. 2' Max 3' Min.

B) 2' Min. 3' Max 4' Min.

C) 3' Min. 4' Max 6' Min.

D) 4' Min. 5' Max 7' Min.

E) 5' Min. 6' Max 8' Min.

F) 6' Min. 7' Max 9' Min.

G) 7' Min. 8' Max 10' Min.

Lengths do not include elbow indicated

CB40E Gas Fireplace

GUIDELINES FOR INSTALLING A TV/ARTWORK ABOVE THE UNIT

Note: All wiring should stay free and clear of the vent system to avoid damage

due to heat. We recommend using a metal receptacle box and BX cable (120

volt wire protected by metal sheathing) if located directly in front of the vent

system. Ensure wiring is secured without any sag.

ZERO CLEARANCE TO TV: While most consumers prefer to centrally locate

a wall mounted TV, the “Cool-Touch Wall Technology” means that the bottom

edge of the TV can be installed ush with the bottom edge of the ventilated

replace chase opening.

The TV may be recessed into a wall as shown below.

This can only recess into the chase opening a maximum of 3-1/2 inches

and must be a minimum of 12 inches from the replace lip to the rst stud.

To achieve a maximum of 3-1/2" recess, the wall must be of a maximum

of 2" as shown.

TV RECESSED INTO WALL

The TV cannot be

any lower than this

ﬁnishing lip

3.5”

MAX

3.5”

MAX

2.0”

Vertical 2x4

12.0” MIN

Horizontal 2x4

15.5” MIN

15.5”

3.5”

2”

3.5”

MAX

12.0”

20.0”

16.5”

Sample Install 1 Sample Install 2

Airow

Zone

Do not

obstruct

3.5”

MAX

3.5”

MAX

2.0”

Vertical 2x4

12.0” MIN

Horizontal 2x4

15.5” MIN

15.5”

3.5”

2”

3.5”

MAX

12.0”

20.0”

16.5”

Sample Install 1 Sample Install 2

Airow

Zone

Do not

obstruct

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency L676S-LP1 Sunrise Bedienungsanleitung

Regency

Regency U1500E-NG11 Bedienungsanleitung

Regency

Regency E18-NG Kurzanleitung

Regency

Regency Excalibur P90 Zero Clearance Kurzanleitung

Regency

Regency Panorama P33E-NG11 Bedienungsanleitung

Regency

Regency Horizon HZ40E-NG Kurzanleitung

Regency

Regency Contura RC500EX Kurzanleitung

Regency

Regency GEM54-NG Bedienungsanleitung

Regency

Regency G51-NG UltraGlow Kurzanleitung

Regency

Regency Vancouver F2402M Kurzanleitung

Regency

Regency Liberty L900 Gas Fireplace L900-NG1 Kurzanleitung

Regency

Regency Grandview G800EC Series Kurzanleitung

Regency

Regency Liberty L965E Service-Handbuch

Regency

Regency bellavista B36XTCE Kurzanleitung

Regency

Regency PG121-NG Kurzanleitung

Regency

Regency Sunrise P33SE-NG4 Kurzanleitung

Regency

Regency PTO30-NG1 Kurzanleitung

Regency

Regency City CB50E Kurzanleitung

Regency

Regency Greenfire GF1500L NG-2 Bedienungsanleitung

Regency

Regency Classic I2405M Kurzanleitung

Regency

Regency FPI FP90 Kurzanleitung

Regency

Regency Bellavista B36X Kurzanleitung

Regency

Regency L540EB Kurzanleitung

Regency

Regency GF900C-NG1 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung