Regency City Series Bedienungsanleitung

City Series CB60E | 1

City Series CB60E Gas Fireplace

MODEL CB60E-NG CB60E-LP

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)

Manifold Pressure - High 3.8” W.C. (0.94 kPa) 10.5” W.C. (2.62

kPa)

Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa)

Oriﬁce Size -Altitude 0-4500 ft # 32 DMS # 50 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

21,000 Btu/h

(6.15 kW)

19,500 Btu/h

(5.71 kW)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

39,000 Btu/h

(11.42 kW)

36,000 Btu/h

(10.54 kW)

Vent Sizing 5” Inner / 8” Outer 5” Inner / 8” Outer

71 1

1810 mm

11"

279 mm

18"

466 mm

10 1

260 mm

35 5

905 mm

72 5

1837 mm

35 5

905 mm

204 mm

127 mm

13"

330 mm

7 1

185 mm

20 5

515 mm

39"

990 mm

CB60E Dimensions - Bay Install

2 | City Series CB60E

CB60E Dimensions - (Corner Install)

71 1

1810 mm

11"

279 mm

18"

466 mm

10 1

263 mm

35 5

905 mm

72 5

1837 mm

35 5

905 mm

204 mm

127 mm

13"

330 mm

7 1

185 mm

20 5

515 mm

39"

990 mm

16 9

421 mm

City Series CB60E | 3

CLEARANCES CB60E (3-SIDED)

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ﬁres is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance

that this ﬁreplace and vent system be installed only in accordance with these instructions.

Flue Clearances to Combustibles

Horizontal - Top 3"

Horizontal - Side 2"

Horizontal - Bottom 2"

Vertical 2"

Passing through wall/

floor/ceiling - when

restop is used.

1-1/2"

Note: This appliance uses 5" x 8" venting.

Caution Requirements

The top, back and sides of the ﬁreplace are deﬁned by

standoffs. The metal ends of the standoff may NOT be

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not adhered

to. It is of greatest importance that this ﬁreplace and vent system be

installed only in accordance with these instructions.

The HeatWave Duct Kit has different

clearance and framing require-

ments, check the HeatWave manual

for details.

Alcove

Clearance: Dimension Measured From:

A1: Mantel Height (min.) ** Top of Fireplace Opening

A: From Floor (min.) 10-1/4" (260 mm) Bottom of Fireplace Opening

B: Sidewall (on one side) min. 5 7/8" (149 mm) Side of Fireplace Opening

C: Enclosure Width (min.) 71-1/4" (1810 mm) Minimum inside dimensions

D: Mantel Depth (max.) **

E: Alcove Width 119.5" (3035 mm) Sidewall to Sidewall (Minimum)

F: Alcove Depth 35" (889 mm) Front to Unit (Maximum)

G: Convection Air Outlet Opening Offset

(min.) 1" (25 mm) Max. offset from top of chase enclosure

H: Convection Air Outlet 180 square inches

I Enclosure Depth (min.) 20-5/16" (516 mm) Minimum inside dimensions

J: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening

K: To Ceiling (min.) all 3 sides 1-3/4" To Top of Ceiling

L: Chase Enclosure (min.) 81-1/4" (2064 mm) From base of unit/ﬂoor to top of enclosure

M:Clearance to Sprinkler Head (min.) 36" (914mm) Perpendicular from chase grill

Hearth 0" No hearth required

** See mantel clearances chart in the manual.

Chase grill

Sprinkler

Side view

4 | City Series CB60E

CLEARANCES CB60E (3-SIDED)

Floor to ceiling with top opening Full framing with vents in front/sides or top

Full framing with low vents in front or sides Full framing with vents in front or sides

opening opening

City Series CB60E | 5

CLEARANCES CB60E (Corner Install)

Caution Requirements

The top, back and sides of the ﬁreplace are deﬁned by

standoffs. The metal ends of the standoff may NOT be

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk

if these clearances (air space) to combustible materials are not adhered

to. It is of greatest importance that this ﬁreplace and vent system be

installed only in accordance with these instructions.

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ﬁres is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that

this ﬁreplace and vent system be installed only in accordance with these instructions.

Note: Left handed corner shown in illustration. Clearances will be the same for the right hand side.

Clearance: Dimension Measured From:

A: Mantel Height (min.) ** Top of Fireplace Opening

B: Opening Height 18" (457 mm) Bottom/Top of Fireplace Opening

C: From Floor (min.) 10-1/4" (260 mm) Bottom of Fireplace Opening

D: Sidewall (on one side) min. 39" (991 mm) Side of Fireplace Opening

E: Mantel Depth (max.) ** Front of Fireplace Opening

F: Alcove Depth 35" (889 mm) Front of Fireplace Opening

G: Convection Air Outlet 180 square inches

H: Convection Air Outlet Opening Offset *1" (25 mm) Max. offset from top of chase enclosure

I: Chase Enclosure (Min.) 81-1/4" (2064 mm) From Base of Unit/Floor to top of enclosure

Hearth 0" No hearth required

** See mantel clearances chart in this manual.

Flue Clearances to Combustibles

Horizontal - Top 3"

Horizontal - Side 2"

Horizontal - Bottom 2"

Vertical 2"

Passing through wall/

floor/ceiling - when

ﬁrestop is used.

1-1/2"

Top View

Alcove

The HeatWave Duct Kit has different

clearance and framing require-

ments, check the HeatWave manual

for details.

Left Corner

Shown

6 | City Series CB60E

MANTEL CLEARANCES CB60E (3-SIDED)

Combustible mantel clearances from top of front facing

are shown in the diagram on the right.

Mantel Leg Clearances

Combustible mantel leg clearances as per diagram:

212 6 4810

9”

18-1/16"

Top of

Fireplace

Opening

12" (305mm)

1/2" Drywall, wood, wood panel, etc.

5 1/4"

To Bottom of

Fireplace

Opening

12"

MANTEL LEG

City Series CB60E | 7

FRAMING DIMENSIONS CB60E (3-SIDED)

NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.

Framing

Dimensions Description CB60E

A Framing Height 41-1/4" (1 048 mm)

B Framing Width 71-1/4" (1810 mm)

C* Framing Depth 20-5/16" (516 mm)

D Minimum Height to Combustibles 81-1/4" (2038 mm)

G Vent Centerline Height 58-3/16" (1478 mm)

** Gas Connection Opening Height See gas connection location in this manual

** Gas Connection Height See gas connection location in this manual

** Gas Connection Inset-Centre Opening See gas connection location in this manual

* Not in diagram below

** See manual for alternate Gas/ Electrical connection options

Note: A combined minimum of

180 square inches of open area

is required for the convection air

outlet to cool the enclosure. En-

sure clearances for Convection Air

Outlets are met.

See clearances CB60E in this man-

ual as there are different methods

as to how this can be achieved.

Note: This appliance must be

installed on a solid surface

such as a plywood floor

which must be the full width

and depth of the appliance.

Ensure that the wood base that the appliance will sit on is strong enough to support the full weight of this appliance.

The overall weight of this appliance is 460 pounds (shipping weight).

Note: Unit must be installed onto a solid

backwall - do not install directly onto studs.

Note : The framing depth does not take into

account drywall/wood or similar materials

against the back wall. The framing depth will

need to change based on the thickness of the

material (example: 20-5/16 framing depth +

1/2 drywall = 20 13/16")

8 | City Series CB60E

NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.

Note: A combined minimum of 180

square inches of open area is required

for the convection air outlet to cool

the enclosure. Ensure clearances for

Convection Air Outlets are met.

See clearances CB60E in this manual

as there are different methods as to

how this can be achieved.

Note: This appliance must be in-

stalled on a level and solid surface

such as a plywood ﬂoor which must

be the full width and depth of the

appliance.

Framing

Dimensions Description Corner Kit

A Framing Height 41-1/4” (1048 mm)

B Framing Width 71-1/4" (1810 mm)

C Framing Depth 20-5/16" (516mm)

D Unit Base to Top Enclosure (Min.) 81-1/4"(2038 mm)

G Vent Centerline Height 58-3/16" (1478 mm)

NOTE: Unit cannot be load-bearing. All ﬁnishing materials must be supported by the framing.

Maximum material

dimensions 2" x 4" for

header studs (installed

on edge and ﬂat)

Framing Dimensions Corner Kit - Corner Install

(Right Corner)

City Series CB60E | 9

NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.

Note: A combined minimum of

180 square inches of open area

is required for the convection air

outlet to cool the enclosure.

Ensure clearances for

Convection Air Outlets are met.

See clearances CB60E in this

manual as there are different

methods as to how this can be

achieved.

NOTE: Unit cannot be load-bearing. All ﬁnishing materials must be supported by the framing.

Note: This appliance must be in-

stalled on a level and solid surface

such as a plywood ﬂoor which must

be the full width and depth of the

appliance.

Maximum material

dimensions 2" x 4" for

header studs (installed

on edge and ﬂat)

Framing

Dimensions Description Corner Kit

A Framing Height 41-1/4” (1048 mm)

B Framing Width 71-1/4" (1810 mm)

C Framing Depth 20-5/16" (516mm)

D Unit Base to Top Enclosure (Min.) 81-1/4"(2038 mm)

G Vent Centerline Height 58-3/16" (1478 mm)

Framing Dimensions Corner Kit - Corner Install

(Left Corner)

Andere Handbücher für City Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Regency Kamin im Innenbereich Handbücher

Regency

Regency GFI300LNG-R Bedienungsanleitung

Regency

Regency E21-NG10 Kurzanleitung

Regency

Regency GF1500LST-NG Kurzanleitung

Regency

Regency City Series San Francisco Bay 40 Bedienungsanleitung

Regency

Regency B36XT Bellavista Kurzanleitung

Regency

Regency R12 Bedienungsanleitung

Regency

Regency L540E Kurzanleitung

Regency

Regency Grandview G800EC Series Bedienungsanleitung

Regency

Regency Excalibur P90 Bedienungsanleitung

Regency

Regency Horizon HZ30E-NG1 Kurzanleitung

Regency

Regency Greenfire GF900L Bedienungsanleitung

Regency

Regency 510-994 Bedienungsanleitung

Regency

Regency Excalibur P90 Zero Clearance Kurzanleitung

Regency

Regency F5102 - AUSTRALIA Kurzanleitung

Regency

Regency Grandview G600C-1 Kurzanleitung

Regency

Regency Gi29L Series Bedienungsanleitung

Regency

Regency Sunrise P33S-NG4 Kurzanleitung

Regency

Regency Panorama P121 Kurzanleitung

Regency

Regency P36-NG5 Kurzanleitung

Regency

Regency GR44-3 and Betriebsanleitung

Regency

Regency Sunrise E33S-NG1 Kurzanleitung

Regency

Regency PANORAMA P33E Kurzanleitung

Regency

Regency Classic i2450 Bedienungsanleitung

Regency

Regency Greenfire GF1500L Series Kurzanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch