Regency Hampton GC60-2 Bedienungsanleitung
GC60-2 Pellet Stove | 1
Hampton GC60-2 Freestanding Pellet Stove
Model GC60-2
Heat Output BTUs 7,817-38,437 BTUs
Emissions (grams/hr) EPA Certied 1.9 gram/hr
Eciency (EPA HHV)*/** 78%
Eciency (EPA LHV) 86%
Flue Size 4" (102 mm)
US Biomass Tax Rebate Eligible*/** Yes
*US Biomass Tax Rebate eligibility is based on the HHV value being
greater than or equal to 75%. *
(229mm)
9"
(76mm)
3"
(76mm)
3"
Side Wall
Back Wall
Adjacent Wall
These dimensions are minimum clearances but it is recommended
that you ensure sufficient room for servicing, routine cleaning and
maintenance.
Side wall to unit 9 inches (229 mm)
Back wall to unit 3 inches (76 mm)
Corner to unit 3 inches (76 mm)
Ceiling height 60 inches (1524 mm)
Alcove Maximum Depth 36 inches (914 mm)
Alcove Minimum Width 48 inches (1219 mm)
Alcove Minimum Height 60 inches (1524 mm)
The unit must be installed with a minimum of 6” (152 mm) of oor
protection in front of and to the sides of the door opening.
CLEARANCES TO COMBUSTIBLES
29"
(737mm)
31-1/2"
(800mm)
29-1/2"
(749mm)
23"
(584mm)
28-1/2"
(724mm)
18-3/4"
(476mm)
28-12"
(724mm)
3” Fresh Air Intake 4” Exhaust
4” Exhaust
29"
(737mm)
31-1/2"
(800mm)
29-1/2"
(749mm)
23"
(584mm)
28-1/2"
(724mm)
18-3/4"
(476mm)
28-12"
(724mm)
3” Fresh Air Intake 4” Exhaust
4” Exhaust
DIMENSIONS
**When using optional top vent adaptor kit (GC60-920) and 4’’ to 6’’
ue adaptor (4PVP-X6). See instruction manual for further information.
2 | GC60-2 Pellet Stove
EXHAUST AND FRESH AIR
INTAKE LOCATION
MOBILE HOME INSTALLATION
THIS UNIT USES A 4” EXHAUST VENT.
EXHAUST:
Base of unit to center of flue 14-1/2” (368 mm)
Center of unit to center of flue 6-1/2” (162 mm)
FRESH AIR INTAKE:
Base of unit to center of intake 11” (279 mm)
Center of unit to center of intake 4-7/8” (126 mm)
11”
4-7/8" 6-1/2” 7-3/4”9-1/4"
14-1/2”
Optional Hearth Pad
Flooring
Steel Frame
Ground Wire Directly to Metal Chassis
1/4"Lag Bolts
Securely Fastened
• Secure the heater to the floor using the four (4) holes in the
pedestal.
• Ensure the unit is electrically grounded to the chassis of your
home (permanently).
• Do not install in a room people sleep in.
• Outside fresh air is mandatory. Secure outside air connections
directly to fresh air intake pipe and secure with three (3) screws
evenly spaced.
• All specified components must be used. Do not use any
components other than what’s specified.
GC60-2 Pellet Stove | 3
MAX
4'
Wall Thimble
Horizontal frame
for thimble
Clean out Tee
Wall framing
Vertical
section of
4" vent
pipe
Wall Strap
4" 90
Elbow with
Screen or
Termination Cap
Wall Strap
Concrete Wall
Clean Out Tee
Wall Framing
Horizontal frame
for thimble
4" 90
Elbow
Vertical section
of 4" pipe
Wall Thimble
4" 45
Elbow
with screen or
Termination
Cap
THROUGH WALL WITH VERTICAL RISE AND HORIZONTAL TERMINATION INSTALLATION
THROUGH CONCRETE WALL WITH VERTICAL RISE INSTALLATIONS
(610mm)
MIN 24"
4' (1220mm) MAX
All around
3"MIN Clearance
(75mm)
3"(76mm) MIN.
Rain Cap
Storm Collar
Flashing
Clean Out Tee
Wall Thimble
Wall Strap
Horizontal
Frame for
Thimble
OUTSIDE VERTICAL INSTALLATIONS
To accomplish an outside vertical pipe installation, follow the “Horizontal ExHaust tHrougH Wall installations” section
and then finish it by performing the following (refer to Figure 15).
1. Install a tee with clean out on the outside of the house.
2. Install PL vent upward from the tee. Make sure that you install support brackets to keep the vent straight and
secure. All joints in the exhaust venting system must be fastened with at least three (3) screws.
3. Install ceiling thimble and secure the flashing as you go through the roof.
4. Ensure that the rain cap is a minimum of 24” (61 cm) above the roof.
4 | GC60-2 Pellet Stove
2 ft
(61 cm)
Rain Cap (ensure
cap is at least 3ft
(91cm) above the
roof at the lowest
point
Roof Flashing
Roof Rafter
Fire Stop with
Support Collar
Ceiling Joist
Vertical Vent Pipe
Clean Out Tee
with Pipe Adapter
NOTE: All vent sections must
maintain the clearances to
combustibles set out by the
vent manufacturer.
INSIDE VERTICAL INSTALLATIONS
1. Place the unit on the hearth pad if a hearth pad is to be used (or on solid material if installed on a carpeted
surface) and space the unit in a manner so when the pellet vent is installed vertically, it will meet the minimum
clearance from a combustible wall stated by the vent manufacturer.
2. Install the tee with clean out.
3. Install the pellet vent upward from tee. When you reach the ceiling, make sure that the vent goes through a
ceiling fire stop. Keep attic insulation away from the vent pipe & maintain an effective vapor barrier. All joints
in the exhaust venting system must be fastened with at least three (3) screws. Refer to vent manufacturer for
distance to combustibles & follow the vent manufacturer’s instructions on sealing.
4. Finally, extend the pellet vent to go through the roof flashing.
5. Ensure that the rain cap is a minimum of 24” (61 cm) above the roof.
6. Install the fresh air system.
GC60-2 Pellet Stove | 5
Existing Fireplace
Clean Out Tee
Fireplace Damper
Location
Rain Cap
Seal Plate
Vent Pipe (single wall
stainless flex pipe or
PL vent)
Existing Masonary
Flue
Flexible Vent Connector
(Use this 5 ft section of
pipe to vent past fireplace
damper or smoke shelf)
Floor
Protection
Combustible Floor
Masonry Fireplace
Min (6")
150mm
Mantel
Minimum (8") 200mm
from top of stove
Damper Removed
or Fastened Open
Clean-out tee
Fresh-air intake should com
from chimney. If holes
already exist fresh-air intake
can be taken through back
of the fireplace or through
the ash dump.
HEARTH MOUNT INSTALLATION
Hearth Mount - Side View
Hearth Mount - Over View
1. Lock fireplace damper in the open position.
2. Install flexible stainless steel liner or listed pellet
vent to the top of the chimney. All joints in the
exhaust venting system must be fastened with
at least three (3) screws.
3. Install a sealing plate at the top of the chimney.
4. Connect a rain cap and flex adapter to the
chimney liner/pipe.
5. Connect a clean-out tee or a 90° elbow to the
liner/pipe.
6. Install tee onto stove.
6 | GC60-2 Pellet Stove
TOP VENT ADAPTOR KIT & 4” (102 MM) TO 6” (152 MM) FLUE ADAPTOR
(APPROVED FOR VERTICAL INSTALLATIONS ONLY)
*In order to achieve the maximum rated eciency of 78% HHV purchase of a top vent adaptor kit (GC60-920) is required.
Use the sheet metal screws provided to attach the kit to the rear of the unit as shown. Please see kit instruction manual for more
detailed installation instructions.
The stove must also be connected to a 6” (152 mm) Class A ue (where permitted) using the 4” (102 mm) to 6” (152 mm) Flue
Adaptor (4PVP-X6).
See separate instruction manual for complete details.
Note: Part # 6DVL-ADT Simpson Duravent DVL adaptor would also be required to connect the 4" (102 mm) - 6" (152 mm) increaser
to class A chimney when going through the wall or ceiling when using Simpson Duravent Duraplus/Duratech chimney systems. Not
required with DuraTech Premium or DuraTech Canada. DTC ceiling supports feature a built-in ue extension which eliminates the
need for this Simpson Duravent DVL adaptor.
4PVP-X6
4’’ (102 mm) pipe
lengths to class A
chimney
GC60-920
Hampton GC60-2 Cast Pellet Stove Technical Manual
20
GC60-2 Pellet Stove | 7
Inhaltsverzeichnis
Andere Regency Herd Handbücher
Regency
Regency ULTIMATE U41FS-NG Bedienungsanleitung
Regency
Regency ULTIMATE U38 Bedienungsanleitung
Regency
Regency Ultimate U39E Series Kurzanleitung
Regency
Regency ULTIMATE U27-LP1 Kurzanleitung
Regency
Regency Ultimate U39EX Kurzanleitung
Regency
Regency Ultimate U45-NG Bedienungsanleitung
Regency
Regency F2400M Kurzanleitung
Regency
Regency C33-LP3 Kurzanleitung
Regency
Regency C33 Classic Kurzanleitung
Regency
Regency Classic C34 Series Kurzanleitung
Regency
Regency FG39-NG2 Kurzanleitung
Regency
Regency Classic C34 Kurzanleitung
Regency
Regency FireGenieFG39-LPG2 Kurzanleitung
Regency
Regency Ultimate U38-NG1 Kurzanleitung
Regency
Regency ULTIMATE U38-LP Kurzanleitung
Regency
Regency F1500 Bedienungsanleitung
Regency
Regency Vancouver F2402M Kurzanleitung
Regency
Regency Classic C34 Kurzanleitung
Regency
Regency ULTIMATE U43-NG Bedienungsanleitung
Regency
Regency Ultimate U39 Kurzanleitung
Beliebte Herd Handbücher anderer Marken
Vermont Castings
Vermont Castings Intrepid 2 Bedienungsanleitung
Italiana Camini
Italiana Camini CLASSICA Kurzanleitung
Avalon
Avalon Vashon Avanti DVS FS Bedienungsanleitung
Spartherm
Spartherm ambiente a1 Bedienungsanleitung
Dimplex
Dimplex MCFSTV12AU Bedienungsanleitung
Warmlite
Warmlite WL46040 Bedienungsanleitung