Remington HyperFlex SHAVE & TRIM XR1390AU Bedienungsanleitung

2 YEAR WARRANTY

To register your product go to

www.remington-products.com.au

XR139 0AU

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should

always be observed, including the following.

READ ALL INSTRUCTIONS BEFORE USING

For additional protection, the installation of a residual

current device (rcd) having a rated residual operating

current not exceeding 30 mA is advisable in the electrical

circuit supplying the bathroom. Ask your installer for advice.

WARNING - TO REDUCE THE RISK OF BURNS,

ELECTROCUTION AND FIRE OR INJURY TO PERSONS

DANGER - As with most electrical appliances, electrical

parts are electrically live even when the switch is off.

• The appliance should never be left unattended when plugged

into a power outlet, except when charging the appliance.

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by

children without supervision.

• Never operate this appliance if it has a damaged cord or

plug, if it is not working correctly, if it has been dropped or

damaged, or dropped into water. If the supply cord or plug

of the appliance is damaged it must be replaced by the

manufacturer, its service agent or similarly qualified persons

in order to avoid a hazard. It cannot be repaired. Keep the

cord away from heated surfaces.

• Charge, use and store the product at a temperature between

0°C and 32°C.

• Do not use outdoors or where aerosol (spray) products are

being used, or where oxygen is being administered.

• Do not use this appliance with damaged or broken tracks or

cutters, as injury may occur.

• Do not plug or unplug the appliance with wet hands.

• For household use only.

• Do not place or store the appliance or charging adaptor

where it can fall or be knocked into a sink or bath.

• Do not place in or drop into water or any other liquid.

• If an appliance falls into water, “unplug it” immediately. Do

not reach into the water.

• Unplug the charging adaptor from the electrical outlet

immediately after fully charging.

• Do not use while bathing or in the shower.

• Unplug and switch off this appliance before cleaning it.

• Use this appliance only for its intended use as described in

this manual.

• Do not use attachments not recommended by Remington.

• Never drop or insert any object into any opening of this

appliance.

• Always store the charging adaptor in a moisture-free

location.

• Do not use on people who are asleep.

• Do not use an extension cord or a voltage converter with this

appliance.

• Do not wrap the cord around the appliance.

Remington strongly recommends that an approved Safety Switch

(Residual current device) be installed to protect all bathroom

power outlets. Ask an electrical contractor for advice.

SAVE THESE INSTRUCTIONS

XR1390AU SHAVE & TRIM

USE & CARE INSTRUCTION MANUAL

Thank you for purchasing your new Remington® HyperFlex Shave & Trim.

Inside this manual you will ﬁnd tips on using and caring for your shaver.

KEY PARTS

1. Pivoting head & cutter assembly

2. Individual flexing heads

3. Hairpocket

4. Pop-up trimmer (rear)

5. On/Off push button

6. LCD display

7. Charging pins

8. Beard trimmer attachment

9. Beard trimmer comb

Also Includes

• Storage pouch

• Power adaptor

• Charging stand

• Cleaning brush

FEATURE XR1390AU

Power System Cordless

Initial Charge Time 24 Hours

Full Charge Time 90 Minutes

Cordless Shave Time 60 Minutes

Quick Charge Yes

Indicators LCD

Voltage Type Worldwide

Charging Stand Yes

Travel Lock Yes

Shaver head Replacement Part No. SPR-XRAU

Trimmer head Replacement Part No. SPR-XTAU

Power System: Cordless – shaver can only be used without the power cord. The

shaver will not run while it is charging on its charging stand.

Quick Charge: Shaver will charge long enough for one shave in 5 minutes.

Indicator: LCD Panel – displays the number of minutes of remaining battery power.

Voltage Type: Worldwide Voltage – shaver automatically adapts to an outlet

voltage between 100V and 240V.

Note: Some countries will require the use of a plug adaptor that is not included with

your shaver.

Travel Lock: To engage travel lock, press and hold the On/Off button for 3

seconds. To disengage travel lock, press and hold the On/Off button for 3 seconds.

CHARGING

1. Plug power adaptor into the charging stand. (Diagram A)

2. Plug power adaptor into wall outlet. (Diagram B)

3. Charge shaver for 24 hours before its ﬁrst use. This ﬁrst charge is important

to the shaver’s battery life. Note: During initial charge ignore the electronic

indicators as they are in “start up cycle”. (Diagram C)

4. Use shaver until recharge is required.

CAUTION!

• Make sure the shaver and your hands are dry when charging the shaver.

• Always charge the shaver in a cool, dry place.

SHAVING

1. Press power button to turn on. (Diagram D)

2. Shave face and neck using short, circular strokes. (Diagram E)

3. After shaving, turn the shaver off. (Diagram D)

A B C

SHAVING TIPS

• Remington HyperFlex shavers are showerproof. You may use shaving foam or

cream with your shaver. You may also shave in the shower.

• Wait at least 15 minutes after getting up before shaving, to ensure your face

is free of pufﬁness that may be present from sleeping.

• Always hold the shaver at a right angle to the skin so that all three heads are

touching the skin with equal pressure.

• Stretch skin with the free hand so hairs stand upright, making it easier for

them to enter the cutting chamber.

• Use moderate to slow, circular stroking movement.

• The use of short, circular motions in stubborn areas may obtain a closer

shave, especially along the neck and chin line.

• Do not press hard against the skin to avoid skin irritation and/or damage to

the rotary heads.

TRIM

Beard Trimmer:

To remove the shaver head, simply pull upwards from the neck of the shaver for

easy release.

To attach the beard trimmer attachment, align it with the neck attachment cavity so

that it clips into position.

The beard trimmers micro setting zoom comb can be adjusted to suit your required

length setting type of between 2-6mm. The setting can be adjusted by turning the

wheel either left or right.

Without the beard comb attachment, the length of hair cut will be 0.4mm.

Pop-up Trimmer:

1. Push trimmer release button to engage trimmer. (Diagram F)

2. Trim long, difﬁcult hairs and side burns.

3. Close trimmer by pressing down. (Diagram G)

F G

CLEANING & CARE

The shaver is a washable apliance. The head and body may be cleaned

under warm water.

NOTE: **When cleaning your shaver, make sure the shaver is turned off and

disconnected from the power cord.**

CAUTION!

• When cleaning the external surfaces of the shaver, do not use strong

detergents or other chemicals.

• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer

or heater to dry the shaver.

NOTE: **The shaver head and neck assembly is designed to be detachable

from the shaver body. Simply pull upwards from the neck of the shaver for

easy release. To reattach neck, align it with the neck attachment cavity so

that it clips back into position.**

Daily:

1. Locate the detachment grooves on the head & cutter assembly. Gently pull to

detach the hair pocket from the neck assembly. (Diagram L)

2. Tap out excess hair shavings.

3. Rinse the head of the shaver in running water.

4. Gently reattach the hair pocket to the neck assembly until it locks in place on

all three sides. The hair pocket may be reattached in any conﬁguration.

1. Head & cutter (hair pocket) assembly

2. Detachment grooves

3. Neck assembly

4. Neck attachment cavity

5. Beard trimmer attachment

1234

Cleaning the Beard Trimmer Attachment

Clean the beard trimmer attachment with the cleaning brush provided, brush away

hair clippings from the blades, and top of trimmer handle.

NOTE: If you rinse these attachments with cool or warm water (never use hot

water) or use it in the shower then the blades will need to be lubricated with light-

grade oil or sewing machine oil (1-2 drops over the cutters) every month.

Weekly:

1. Perform the daily cleaning steps 1 and 2.

2. Remove the hair pocket from the head & cutter assembly. (Diagram L) Place

the body of the shaver aside.

3. Slide the blue cutter support frame upwards towards the direction of the two

cutters to release it from the assembly. (Diagram M)

4. Lift and remove the cutter support frame away from the cutters.

5. Remove the cutters. (Diagram N)

6. Thoroughly rinse away any debris from inner and outer cutters with warm

water.

7. Replace the inner cutters. (Diagram O) The inner and outer cutters are colour

coded (orange, blue and black) to ensure each cutter is returned to its original

and most effective position on the cutter assembly.

8. Hold the cutter support frame with the raised center section facing upwards.

Place it over the cutters so that the centre mouth opening is facing the blue

cutter. Slide the cutter carrier towards the blue cutter until the locking tab

locks under the centre triangle. (Diagram P)

9. Lubricate each cutter with Remington Shaver Saver (SP4).

10. Gently reattach the hair pocket to the neck assembly until it lock in place

on all three sides. The hair pocket may be reattached in any conﬁguration.

(Diagram Q)

** Pop Up Trimmer: Lubricate teeth with oil every six months

LMNO

REPLACING YOUR HEADS & CUTTERS

Please refer to the shaver grid on page 5 of this manual that lists the correct

replacement part number for your shaver.

It is very important to replace your head and cutters when necessary to ensure

a close, comfortable shave without irritation. We recommend they be replaced

every 12 months. Here are some signs of head and cutter wear, indicating that

replacement is needed:

• Irritation: As the heads get excessively worn you may experience some skin

irritation. This would be especially noticeable when you apply moisturizing

lotion.

• Pulling: When the cutters wear you may feel a sense of pulling and a loss of

closeness when you shave. This is an indication that it is time to replace your

heads and cutters.

Replacement heads & cutters may be obtained from your local retailer, or

directly from Remington®. Simply ﬁll out the enclosed accessory order form or

alternatively your order can be processed over the phone via the Remington®

Service Hotline - refer to page 12.

This product is not suitable to use in a bath.

This product conforms to radio frequency interference requirements

Any product purchased and used commercially carries a limited 90 Day Warranty.

MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY

If within 60 days you are not fully satisfied with your Remington® shaver, just return the shaver

with this completed coupon and a copy of your Australian/New Zealand purchase receipt to

Remington®. In return, we will send you a cheque for the full purchase price of the shaver.

Please allow 6-8 weeks for your cheque to arrive.

Name:

Address:

City:

State: Postcode:

Contact No: Area Code: Ph:

Product Model number:

Is this the first Remington shaver you have owned/purchased? Yes No

What is the reason you are returning this product?

Inhaltsverzeichnis

Andere Remington Elektrorasierer Handbücher

Remington

Remington PowerSeries Aqua PR1340 Bedienungsanleitung

Remington

Remington mb4560 Bedienungsanleitung

Remington

Remington HC5856AU Bedienungsanleitung

Remington

Remington SmartEdge XF8700 Bedienungsanleitung

Remington

Remington MB4850 Bedienungsanleitung

Remington

Remington MS3-0004 Bedienungsanleitung

Remington

Remington SMOOTH AND SILKY WDF-4840 Bedienungsanleitung

Remington

Remington Microflex Extra R-845 Bedienungsanleitung

Remington

Remington Trim & Shape MPT3800 Series Bedienungsanleitung

Remington

Remington PrecisionPro MB-200 Bedienungsanleitung

Remington

Remington R456 Bedienungsanleitung

Remington

Remington PG155 Bedienungsanleitung

Remington

Remington i-Light PRO Face&Body IPL6000FAU Bedienungsanleitung

Remington

Remington Men's Shaver Bedienungsanleitung

Remington

Remington MB6550 Bedienungsanleitung

Remington

Remington MB4555 Bedienungsanleitung

Remington

Remington NE3550 Bedienungsanleitung

Remington

Remington Style Series Bedienungsanleitung

Remington

Remington PR1330 Bedienungsanleitung

Remington

Remington SMOOTH AND SILKY WDF-4840 Bedienungsanleitung

Remington

Remington HG5000 Bedienungsanleitung

Remington

Remington X5 Limitless Bedienungsanleitung

Remington

Remington Smooth & Silky WDF-1200 Bedienungsanleitung

Remington

Remington R4150 Bedienungsanleitung

Beliebte Elektrorasierer Handbücher anderer Marken

Philips

Philips MicroAction 4402LC Bedienungsanleitung

Philips

Philips HQ7740 Bedienungsanleitung

Philips

Philips Norelco BG2022 Bodygroom Bedienungsanleitung

Norelco

Norelco Quadra 7610X Bedienungsanleitung

Philips

Philips 7616X Bedienungsanleitung

Philips

Philips HQ802 Bedienungsanleitung

Philips

Philips HQ7363/17 Bedienungsanleitung

Braun

Braun WaterFlex WF2s Bedienungsanleitung

Philips

Philips NORELCO S7371 Bedienungsanleitung

Daga

Daga MT-400 Handbuch

Philips

Philips Bodygroom BG2000 Bedienungsanleitung

Kompernass

Kompernass KH 5537 Bedienungsanleitung

Philips

Philips qc5365 Bedienungsanleitung

MIA

MIA Aqua Body Bedienungsanleitung

Philips

Philips NORELCO AT880 Bedienungsanleitung

Matheo

Matheo MLR 15 Bedienungsanleitung

Philips

Philips 7735X Bedienungsanleitung

Braun

Braun silk-epil 5 Bedienungsanleitung