Remington HC5900 Bedienungsanleitung

HC5900

PrecisionCut Hair Clipper

£10,000 prize draw

EXTRA year guarantee

FREE rewards gallery

Visit www.remington.co.uk/productregister

You must register within 28 days

of purchase.

Thank you for buying your new Remington® product. Please read these

instructions carefully and keep them safe. Remove all packaging before use.

F IMPORTANT SAFETY INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE OR INJURY

TO PERSONS:

1 This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been supervised/instructed and

understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be done by children unless they are

older than 8 and supervised. Keep the appliance and cable out of reach of

children under 8 years.

2 The adaptor contains a transformer. Do not cut o the adaptor to replace it

with another plug, as this causes a hazardous situation.

3 Do not leave the appliance unattended while plugged in.

4 Keep the power plug and cord away from heated surfaces.

5 Make sure the power plug and cord do not get wet.

6 Do not plug or unplug the appliance with wet hands.

7 Do not use the product with a damaged cord. A replacement adaptor can be

obtained via our International Service Centres.

8 Do not twist or kink the cable, or wrap it round the appliance.

9 Charge, use and store the product at a temperature between 10°C and 35°C.

10 This appliance is not intended for commercial or salon use.

11 Do not reach for an appliance that has fallen into water. Unplug it

immediately.

12 Suitable for cleaning under an open water tap.

13 This appliance should be supplied with approved safety isolating

adaptors PA-4515E (for EU), PA-4515U (for UK) with the output capacity of

4.5Vdc; 1500mA (adaptor output).

CKEY FEATURES

1 On/O/Turbo Switch 5 LED fuel gauge

2 Blade set 6 Micro USB port

3 2 attachment guide combs 7 Adaptor (not shown)

1-21mm and 24-44mm (not shown) 8 Slide select adjustable comb switch

4 Blade release button

CGETTING STARTED

,CHARGING YOUR APPLIANCE

•Before using your hairclipper for the rst time, charge for 4 hours.

• Ensuretheproductisswitchedo.

• Connectthechargingadaptortotheproductandthentothemains.

• Iftheproductisnotgoingtobeusedforanextendedperiodoftime(2–3

months), unplug it from the mains and store.

• Fullyrechargeyourhairclipperwhenyouwouldliketouseitagain.

• Allow4hoursforacompletecharge.

• TheclipperfeaturesaLEDfuelgaugetoshowremainingchargeand

charging status, please see the tables below:

When connected to the mains and charging

Battery: below 20%

capacity

Red LED ash once per

second

Battery: 20-40%

capacity

Yellow LED ash once

per second

Battery: 40-100%

capacity

Blue LED ash once per

second

Battery:100% capacity Blue LED will be solid

When using cordless

Battery: 40-100%

capacity

Blue LED will be

illuminated

Battery: 20-40%

capacity

Yellow LED will be

illuminated

Battery: below 20%

capacity

Red LED will be

illuminated

Battery: below 5%

capacity

Red LED will ash once

per half second

When using cordless and Turbo is activated

Battery: 40-100%

capacity

Blue LED will illuminate

once every 1.5 seconds

Battery: 20-40%

capacity

Yellow LED will

illuminate once every

1.5 seconds

Battery: below 20%

capacity

Red LED will illuminate

once every 1.5 seconds

Battery: below 5%

capacity

No illumination will

show

When used in corded

mode

Blue LED will illuminate

When using corded in

and Turbo is activated

Blue LED ash once per

1.5 seconds

• Topreservethelifeofyourbatteries,letthemrunoutevery6monthsthen

recharge for 4 hours.

• Theclippercomeswithaquickchargefunction,10minuteschargingwill

give an emergency burst of run time.

,CHARGING VIA STANDARD ELECTRICAL SOCKET

•Ensure the product is switched o.

• Connectthechargingadaptortotheproductandthentothemains.

,USB

• ConnectMicroUSBtotheappliance,andtheUSBconnectortoany 

standard USB port or charger

• ProductwillonlychargethroughUSBandwillnotrunincordedmode.

,CORDED USE

•Connect the charging adaptor to the product then to the mains.

,CAUTION

•Extended mains only use will result in the reduction of the battery life.

,CORDLESS USE

•When the product is switched on and fully charged it can be used in

cordless mode for up to 90 minutes.

F INSTRUCTIONS FOR USE

,BEFORE STARTING THE CUT

• Inspecttheclippermakingsurethatitisfreefromhairanddirt.

• Seatthepersonsothattheirheadisapproximatelyatyoureyelevel.

• Beforecutting,alwayscombthehairsoitistanglefreeanddry.

,TO ATTACH A COMB

•Hold the comb with its teeth upward.

• Toattachacomb,alignthelegsofthecombwiththeholesinthetopofthe

clipper on each side of the blade and slide the legs into the trimmer until the

click.

• Toremove,rmlypullthecombstraightupawayfromtheclipper.

,HAIR CLIPPER COMB SETTINGS

•The clipper comes with two adjustable combs, a short length adjustable

comb (indicated by 1-21mm on the back of the comb) and a longer length

adjustable comb (indicated by 24-44mm on the back of the comb).

• Pleaseseetablebelowfordierentcuttinglengthsavailableoneachcomb:

Shorter Length

Adjustable Comb

Longer length

Adjustable Comb

1mm 24mm

2mm 25mm

3mm 26mm

4mm 27mm

5mm 28mm

6mm 29mm

9mm 32mm

12mm 35mm

15mm 38mm

18mm 41mm

21mm 44mm

•On the slide select switch there is a silver indicator which, when the short

length adjustable comb is on the product, shows the corresponding length

setting on the left of the slide select switch. On the other side of the slide

select switch there is another silver indicator which shows the corresponding

length setting when the longer length adjustable comb is on the product, on

the right side of the slide select switch.

•To adjust the length settings, you must press the upper half of the slide select

switch to release the locking mechanism, then apply force upwards on the

slide select switch to increase the length setting. To decrease the length

settings press the upper part of the slide select switch down and slide

downwards.

• Usetheclipperwithoutanyxedcombsfortrimminghairclosetotheskin.

• Thiswilltrimhairto1mm,holdingtheclippersothebladesare 

perpendicular to the skin will trim hair to 0.5mm.

,INSTRUCTIONS FOR CUTTING HAIR

•To turn the product On or O press the On OFF button. To locate the On/O

button please refer to the key features section.

•For even cutting, allow the comb attachment/blade to cut its way through

 thehair.Donotforceitthroughquickly.Ifyouarecuttingforthersttime,

start with the maximum comb attachment.

,STEP 1 – Nape of the neck

•Set the comb to 3mm or 6mm.

• Holdtheclipperwiththebladeteethpointingupwards.Beginstartingatthe

centre of the head at the base of the neck.

• Slowlylifttheclipper,workingupwardsandoutwardsthroughthehair,

trimming just a little at a time.

,STEP 2 – Back of the head

•With the comb set at 12mm or 18mm, cut the hair at the back of the head.

,STEP 3 – Side of the head

•With the comb set at 3mm or 6mm, trim sideburns. Then change to the

longer 9mm guide comb and continue to cut the top of the head.

,STEP 4 – Top of the head

•Use the longer length comb attachment and set it to 24mm or 27mm then

cut hair on top of the head against the direction in which the hair normally

grows.

• Forlongerhairontop,usethelongerlengthcombattachment(24–44mm)

to achieve the desired style.

• Alwaysworkfromthebackofthehead.

,STEP 5 – The nishing touches

•Use the clipper without an attachment comb for close trimming around the

base and sides of the neck.

• Toproduceacleanstraightlineatthesideburns,reversethehairclipper.

• Placethereversedclipperatrightanglestothehead,tipsoftheblades

lightly touching the skin and then work downwards.

,AUTO TURBO SYSTEM

•Push the power button and the appliance runs in Normal Mode. The Auto

Turbo will automatically activate when the clipper senses it needs more

power.

• ToruninTurbomode,holddownthepowerbuttonfor2secondsandthe

clipper will run in boost until it is turned o.

C CARE FOR YOUR HAIRCLIPPER

• Yourclipperisttedwithhighqualityblades.

• Toensurelonglastingperformanceofyourclipper,cleanthebladesandunit

regularly.

• Alwayskeeptheattachmentguidecombonthetrimmerblade.

,AFTER EACH USE

•Ensure the appliance is switched o and unplugged from the mains before

cleaning.

• Brushtheaccumulatedhairfromthebladesandbodyoftheclipper.

• Tocleanunit,wipewithadampclothanddryimmediately.

• Placeafewdropsofcutterorsewingmachineoilontotheblades.Wipeo

excess oil.

,WASHABLE BLADE CLEANING

,This clipper is fully washable and therefore can be rinsed under a running

tap. However, avoid getting the micro USB port wet.

• Toremovethebladesensuretheunitiso.Pressthebladereleasebutton

on the back of the clipper when it meets the blade and push away from the

clipper.

• Toreattachoncethebladesarecleanedanddry,alignthebottomofthe

blade with the bottom blade housing tab and slide the cartridge back into

place until you hear a click.

• Donotruntheentireunitunderthetap,onlythebladesetismeanttobe

submerged in water.

,EVERY SIX MONTHS

•Remove the 2 screws retaining the xed blade with a screwdriver. Do not

remove blade set.

• Brushouthairsfrombetweenthebladeswithsoftcleaningbrush.Donot

remove the lubricating grease from the blades. It is not necessary to

remove the small moving blade from the unit.

• Ifthemovingbladehasbeenremovedthiscanbere-ttedbyslottingthe

coated blade holder over the pin in the centre of the interior product head.

• Thegrooveonthecoatedblade,justbelowtheteeth,restsonametalplate

at the opposite side to the screw holes. The xed blade is tted with the

raised prole pointing outwards and xed with the 2 screws.

• Ifthebladesarenotcorrectlyaligned,cuttingeciencywillbeimpaired.

,CLEANING CAUTIONS

•Ensure the appliance is switched o and unplugged from the mains before

cleaning.

• Donotuseharshorcorrosivecleanersontheunitsortheirblades.

BATTERY REMOVAL

• Theappliancemustbedisconnectedfromthesupplymainswhen 

removing the battery.

• Turnthetrimmeronanddischargeallremainingpower.

• Removethecombattachment.

• Detachthebladecartridge.

• Prythedecorativepanelothetophousingtoexposethe6screwslocated

in the inner housing.

• Unscrewthe6screws.

• Prytheinnerhousingapartfrombottomhousingtoexposetheinternals

and printed circuit board.

•Remove the battery and printed circuit board assembly from the battery

chamber.

• Disconnectthebatteryfromthecircuitboard.

• Thebatteryistobedisposedofsafely.

H ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous

substances in electrical and electronic goods, appliances marked with

this symbol must not be disposed of with unsorted municipal waste,

but recovered, reused or recycled.

E SERVICE AND GUARANTEE

Defects aecting product functionality appearing within the guarantee period will

be corrected by replacement or repair at our option provided the product is used

and maintained in accordance with the instructions.

Your statutory rights are not aected.

Consumables are excluded.

Defects from repair by an unauthorized dealer are not covered.

If you call the Service Centre, please have the Model No. to hand, as we won’t be

able to help you without it. The Model No. can be found on the rating plate of the

appliance.

Replacement parts and accessories are available to buy at

www.remington.co.uk/parts-accessories

E SERVICE CENTRE

United Kingdom

GTel 0800 212 438 (free call mainland UK)

G+44 161 947 3111 (call outside the UK)

Spectrum Brands (UK) Ltd

Fir Street, Failsworth, Manchester

M35 0HS, UK

www.remington.co.uk

Ireland

GTel 142 951 40

Remington Consumer Products,

Unit B12, Ballymount Corporate Park,

Ballymount, Dublin 12.

www.remington.co.uk

I REGISTER ONLINE FOR

£10,000 prize draw, EXTRA year guarantee, FREE rewards gallery.

Visit www.remington.co.uk/productregister. You must register within 28 days

of purchase.

Inhaltsverzeichnis

Andere Remington Haarschneider Handbücher

Remington

Remington PRECISION PERFORMER HC2000AU Bedienungsanleitung

Remington

Remington HC5015 Bedienungsanleitung

Remington

Remington PRO POWER HC5150 Bedienungsanleitung

Remington

Remington HC5960 Bedienungsanleitung

Remington

Remington NE100C Bedienungsanleitung

Remington

Remington HC5870 Bedienungsanleitung

Remington

Remington X5 Power-X Series Bedienungsanleitung

Remington

Remington HC5780 Bedienungsanleitung

Remington

Remington Classic HC450 Bedienungsanleitung

Remington

Remington Pro Power Alpha HC5156 Bedienungsanleitung

Remington

Remington HC5950 Bedienungsanleitung

Remington

Remington Power X Series Bedienungsanleitung

Remington

Remington HC-70 Bedienungsanleitung

Remington

Remington HighPrecision HC-600 Bedienungsanleitung

Remington

Remington Shortcut clipper SCC-100R Bedienungsanleitung

Remington

Remington Heritage HC9100 Bedienungsanleitung

Remington

Remington ProPower HC5200 Bedienungsanleitung

Remington

Remington HC4110 Bedienungsanleitung

Remington

Remington HC5018 Bedienungsanleitung

Remington

Remington HC335 Bedienungsanleitung

Remington

Remington HC9700 Bedienungsanleitung

Remington

Remington HC2000 Series Bedienungsanleitung

Remington

Remington PrecisionCut HC5302 Bedienungsanleitung

Remington

Remington X4 Power-X Series Bedienungsanleitung

Beliebte Haarschneider Handbücher anderer Marken

Clatronic

Clatronic HSM 800 Bedienungsanleitung

Mellerware

Mellerware MACRO ALDANY MA20001 Bedienungsanleitung

VALERA

VALERA X-Master 652 Bedienungsanleitung

Wahl

Wahl 1870Li Bedienungsanleitung

Lister

Lister Legend Bedienungsanleitung

Philips

Philips HC5440/80 Bedienungsanleitung

Andis

Andis MBA 23125 Bedienungsanleitung

Philips

Philips Philishave HQC488/61 Bedienungsanleitung

Shear Magic

Shear Magic Nifty 1800 Bedienungsanleitung

Philips

Philips QC5390 Bedienungsanleitung

Andis

Andis US-1 Kurzanleitung

Panasonic

Panasonic EH-KA81 Bedienungsanleitung

Philips

Philips HC5450 Bedienungsanleitung

Andis

Andis US-1 Montageanleitung

Andis

Andis ML Montageanleitung

O'Barber

O'Barber MINI SLIDE Bedienungsanleitung

Oster

Oster 76110 Bedienungsanleitung

Hyundai

Hyundai HC 420 Bedienungsanleitung