Remington PrecisionCut HC5500 Bedienungsanleitung

PrecisionCut Hair Clipper

HC5500

HC5700

Thank you for buying your new Remington® product. Please read these

instructions carefully and keep them safe. Remove all packaging before use.

F IMPORTANT SAFETY INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE OR INJURY

TO PERSONS:

1 This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been supervised/instructed and

understand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be done by children unless they are

older than 8 and supervised. Keep the appliance and cable out of reach of

children under 8 years.

2 The adaptor contains a transformer. Do not cut o the adaptor to replace it

with another plug, as this causes a hazardous situation.

3 Use this appliance only for its intended use as described in this manual. Do

not use attachments not recommended by Remington®.

4 Do not use this product if it is not working correctly, if it has been dropped or

damaged, or dropped in water.

5 This appliance should never be left unattended when plugged into a power

outlet, except when charging.

6 Keep the power plug and cord away from heated surfaces.

7 Do not immerse the appliance in liquid; do not use it near water in a

bath-tub, basin or other vessel; and don’t use it outdoors.

8 Make sure the power plug, cord and product unit do not get wet.

9 Do not plug or unplug the appliance with wet hands.

10 Do not immerse in water or any other liquid. Do not rinse under a tap.

11 Do not reach for an appliance that has fallen into water. Unplug it

immediately.

12 Always place and use that appliance on a surface that is uid-resistant.

13 Always put the headguard on the product to protect the cutting heads whilst

travelling.

14 Do not use the appliance, adaptor or any other part if it is damaged, as this

may cause injury. Always replace a damaged adaptor with one of the original

type.

15 Do not twist or kink the cable, or wrap it round the appliance.

16 Charge, use and store the product at a temperature between 10°C and 35°C.

17 This appliance is not intended for commercial or salon use.

18 WARNING: Keep the appliance dry.

ENGLISH

19 HC5500: This appliance should be supplied with approved safety

isolating adaptors PA-3215E (for EU), PA-3215U (for UK) with the output

capacity of 3.2Vdc; 1500mA (adaptor output).

HC5700: This appliance should be supplied with approved safety

isolating adaptors PA-4515E (for EU), PA-4515U (for UK) with the output

capacity of 4.5Vdc; 1500mA (adaptor output).

CKEY FEATURES

1 On/O/Turbo Switch 5 Charging indicator light

2 Blade set 6 Micro USB port

3 2 attachment guide combs 7 Adaptor (not shown)

1-21mm and 24-44mm (not shown) 8 Slide select adjustable comb switch

4 Blade release button

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSI

AE HR

CGETTING STARTED

,CHARGING YOUR APPLIANCE

•Before using your hairclipper for the rst time, charge for 14-16 hours

(HC5500) and 4 hours (HC5700).

• Ensuretheproductisswitchedo.

• Connectthechargingadaptortotheproductandthentothemains.

• Iftheproductisnotgoingtobeusedforanextendedperiodoftime(2–3

months), unplug it from the mains and store.

• Fullyrechargeyourhairclipperwhenyouwouldliketouseitagain.

• Allowfor14-16hoursforafullchargeforHC5500and4hoursforHC5700.

• HC5500:whenchargingtheLEDindicatorwillbeilluminatedandwillremain

illuminated once the product is fully charged.

• HC5700:whenchargingtheLEDindicatorwillbeilluminatedandwillturn

o once the product is fully charged.

• Topreservethelifeofyourbatteries,letthemrunoutevery6monthsthen

recharge for 14-16 hours.

• TheHC5700comeswithaquickchargefunction,10minuteschargingwill

give an emergency burst of run time.

,CHARGING VIA STANDARD ELECTRICAL SOCKET

•Ensure the product is switched o.

• Connectthechargingadaptortotheproductandthentothemains.

,USB

• ConnectMicroUSBtotheappliance,andtheUSBconnectortoanystandard

USB port or charger.

• ProductwillonlychargethroughUSBandwillnotrunincordedmode.

,CORDED USE

•Connect the charging adaptor to the product then to the mains.

,CAUTION

• Extendedmainsonlyusewillresultinthereductionofthebatterylife.

,CORDLESS USE

•When the unit is switched on and fully charged, the product can be used in

cordless mode for up to 60 minutes for the HC5500 and up to 75 minutes for

the HC5700.

ENGLISH

F INSTRUCTIONS FOR USE

,BEFORE STARTING THE CUT

•Inspect the clipper making sure that it is free from hair and dirt.

• Seatthepersonsothattheirheadisapproximatelyatyoureyelevel.

• Beforecutting,alwayscombthehairsoitistanglefreeanddry.

,TO ATTACH A COMB

•Hold the comb with its teeth upward.

• Toattachacomb,alignthelegsofthecombwiththeholesinthetopofthe

clipper on each side of the blade and slide the legs into the trimmer until

they click.

• Toremove,rmlypullthecombstraightupawayfromtheclipper.

,HAIR CLIPPER COMB SETTINGS

•The clipper comes with two adjustable combs, a short length adjustable

comb (indicated by 1-21mm on the back of the comb) and a longer length

adjustable comb (indicated by 24-44mm on the back of the comb).

• Pleaseseetablebelowfordierentcuttinglengthsavailableoneachcomb:

Shorter Length

Adjustable Comb

Longer length

Adjustable Comb

1mm 24mm

2mm 25mm

3mm 26mm

4mm 27mm

5mm 28mm

6mm 29mm

9mm 32mm

12mm 35mm

15mm 38mm

18mm 41mm

21mm 44mm

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSI

AE HR

•On the slide select switch there is a silver indicator which, when the short

length adjustable comb is on the product, shows the corresponding length

setting on the left of the slide select switch. On the other side of the slide

select switch there is another silver indicator which shows the corresponding

length setting when the longer length adjustable comb is on the product, on

the right side of the slide select switch.

•To adjust the length settings, you must press the upper half of the slide select

switch to release the locking mechanism, then apply force upwards on the

slide select switch to increase the length setting. To decrease the length

settings press the upper part of the slide select switch down and slide

downwards.

•Use the clipper without any xed combs for trimming hair close to the skin.

•This will trim hair to 1mm, holding the clipper so the blades are

perpendicular to the skin will trim hair to 0.5mm.

,INSTRUCTIONS FOR CUTTING HAIR

•To turn the product On or O slide the switch. To locate the On/O switch

please refer to the key features section.

•For even cutting, allow the comb attachment/blade to cut its way through

the hair. Do not force it through quickly. If you are cutting for the rst time,

start with the maximum comb attachment.

,STEP 1 – Nape of the neck

•Set the comb to 3mm or 6mm.

•Hold the clipper with the blade teeth pointing upwards. Begin starting at the

centre of the head at the base of the neck.

•Slowly lift the clipper, working upwards and outwards through the hair,

trimming just a little at a time.

,STEP 2 – Back of the head

•With the comb set at 12mm or 18mm, cut the hair at the back of the head.

,STEP 3 – Side of the head

•With the comb set at 3mm or 6mm, trim sideburns. Then change to the

longer 9mm guide comb and continue to cut the top of the head.

,STEP 4 – Top of the head

•Use the longer length comb attachment and set it to 24mm or 27mm then

cut hair on top of the head against the direction in which the hair normally

grows.

ENGLISH

•For longer hair on top, use the longer length comb attachment (24 – 44mm)

to achieve the desired style.

•Always work from the back of the head.

,STEP 5 – The nishing touches

•Use the clipper without an attachment comb for close trimming around the

base and sides of the neck.

•To produce a clean straight line at the sideburns, reverse the hair clipper.

•Place the reversed clipper at right angles to the head, tips of the blades

lightly touching the skin and then work downwards.

,DUAL BOOST SYSTEM (HC5700)

•There is a 3 position switch on HC5700 only. First position is O, second is

normal speed, and third position is Boost for extra power to cut through

thicker hair.

•If the clipper is set to On, it will run at regular power.

•If the clipper is set to Boost, it will provide maximum power.

C CARE FOR YOUR HAIRCLIPPER

• Yourclipperisttedwithhighqualityblades.

• Toensurelonglastingperformanceofyourclipper,cleanthebladesand

unit regularly.

• Alwayskeeptheattachmentguidecombonthetrimmerblade.

,AFTER EACH USE

•Ensure the appliance is switched o and unplugged from the mains before

cleaning.

• Brushtheaccumulatedhairfromthebladesandbodyoftheclipper.Donot

submerge the clipper in water.

• Tocleantheunit,wipewithadampclothanddryimmediately.

• Placeafewdropsofcutterorsewingmachineoilontotheblades.Wipeo

excess oil.

,WASHABLE BLADE CLEANING

•Blade cartridge is removable.

,NOTE: Only the blades on this clipper can be washed under running water.

• Toremovethebladesensuretheunitiso.Pressthebladereleasebutton

on the back of the clipper where it meets the blade and push away from the

clipper.

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSI

AE HR

• Toreattachoncethebladesarecleanedanddry,alignthebottomofthe

blade with the bottom blade housing tab and slide the cartridge back into

place until you hear a click.

• Donotruntheentireunitunderthetap,onlythebladesetismeanttobe

submerged in water.

• Placeafewdropsofcutterorsewingmachineoilontotheblades.Wipeo

excess oil.

,EVERY SIX MONTHS

•At regular intervals the blade set should be removed and cleaned.

• Removethe2screwsretainingthexedbladewithascrewdriver.Donot

remove the blade set.

• Brushouthairsfrombetweenthebladeswithsoftcleaningbrush.Donot

remove the lubricating grease from the blades. It is not necessary to remove

the small moving blade from the unit.

• Ifthemovingbladehasbeenremovedthiscanbere-ttedbyslottingthe

coated blade holder over the pin in the centre of the interior product head.

• Thegrooveonthecoatedblade,justbelowtheteeth,restsonametalplate

at the opposite side to the screw holes. The xed blade is tted with the

raised prole pointing outwards and xed with the 2 screws.

• Ifthebladesarenotcorrectlyaligned,cuttingeciencywillbeimpaired.

• Placeafewdropsofcutterorsewingmachineoilontotheblades.Wipeo

excess oil.

,CLEANING CAUTIONS

•Ensure the appliance is switched o and unplugged from the mains before

cleaning.

• Onlytheattachmentguidecombsandtrimmerblademayberemovedfrom

the product for cleaning.

• Donotrinseunderwater.

• Donotuseharshorcorrosivecleanersontheunitsortheirblades.

BATTERY REMOVAL

• Theappliancemustbedisconnectedfromthesupplymainswhenremoving

the battery.

• Turnthetrimmeronanddischargeallremainingpower.

• Removethecombattachment.

• Detachthebladecartridge.

• Prythedecorativepanelothetophousingtoexposetheinternalsand

printed circuit board.

ENGLISH

• Unscrewthe2screwsonthebigprintedcircuitboardand3screwsonthe

small printed circuit board.

• Removethebatteryandprintedcircuitboardassemblyfromthebattery

chamber.

• Disconnectthebatteryfromthecircuitboard.

• Thebatteryistobedisposedofsafely.

H ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous

substances in electrical and electronic goods, appliances marked with

this symbol must not be disposed of with unsorted municipal waste,

but recovered, reused or recycled.

ENGLISH

GBDNLFEIDKSFINPSKCZ

HUN

PLRUTRROGRSI

AE HR

Vielen Dank, dass Sie sich für den Kauf dieses Remington® Produkts entschieden

haben.

Lesen Sie diese Bedienungsanleitung aufmerksam durch und bewahren Sie sie

auf. Entfernen Sie die Verpackung vor dem Gebrauch vollständig.

F WICHTIGE SICHERHEITSHINWEISE

WARNUNG – ZUR VERMEIDUNG DER GEFAHR VON VERBRENNUNGEN,

STROMSCHLÄGEN, FEUER ODER VERLETZUNGEN AN PERSONEN:

1 Dieses Gerät ist für die Nutzung von Kindern ab 8 Jahren sowie von Personen

mit eingeschränkten physischen, sensorischen oder geistigen Fähigkeiten

oder Mangel an Erfahrung und Wissen geeignet, wenn ihnen die

Handhabung erklärt wurde/ sie dabei beaufsichtigt werden und ihnen die

damit verbundenen Gefahren bewusst sind. Kinder dürfen nicht mit dem

Gerät spielen. Reinigung und Pege dürfen nicht von Kindern durchgeführt

werden, es sei denn sie sind älter als 8 Jahre und werden dabei beaufsichtigt.

Bewahren Sie das Gerät und das Kabel außer Reichweite von Kindern unter 8

Jahren auf.

2 Das Netzteil enthält einen Transformator. Bitte schneiden Sie den

Netzstecker nicht ab, um ihn durch einen anderen Netzstecker zu ersetzen,

da dies gefährlich sein kann.

3 Setzen Sie dieses Gerät ausschließlich zu den in diesem Benutzerhandbuch

beschriebenen Verwendungswecken ein. Verwenden Sie keine Aufsätze, die

nicht von Remington® empfohlen wurden.

4 Verwenden Sie das Gerät nicht, wenn es nicht richtig funktioniert, zu Boden

gefallen, beschädigt oder ins Wasser gefallen ist.

5 Lassen Sie das an das Stromnetz angeschlossene Gerät auf keinen Fall

unbeaufsichtigt, ausgenommen, wenn es gerade aufgeladen wird.

6 Bringen Sie den Netzstecker und das Netzkabel nicht mit beheizten

Oberächen in Berührung.

7 Tauchen Sie das Gerät nicht in Flüssigkeiten. Nicht unter ießendem

Wasser abspülen.

8 Achten Sie darauf, dass der Stromstecker, das Kabel und das Gerät

nicht nass werden.

9 Schließen Sie das Gerät nicht mit nassen Händen an das Stromnetz an.

10 Nicht in Wasser oder andere Flüssigkeiten tauchen. Nicht unter ießendem

Wasser abspülen.

11 Ist das Gerät ins Wasser gefallen, versuchen Sie nicht, es herauszuholen

- ziehen Sie sofort den Netzstecker aus der Steckdose.

12 Das Gerät sollte immer auf eine wasserabweisende Oberäche gestellt und

auch darauf verwendet werden.

DEUTSCH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Remington Haarschneider Handbücher

Remington

Remington HC-5850 Bedienungsanleitung

Remington

Remington HC4250 Bedienungsanleitung

Remington

Remington HC4250AU Bedienungsanleitung

Remington

Remington HC-5030 Bedienungsanleitung

Remington

Remington X6 POWER-X Series Bedienungsanleitung

Remington

Remington ColourCut HC5038 Bedienungsanleitung

Remington

Remington HKVAC2000 Bedienungsanleitung

Remington

Remington HC500 Bedienungsanleitung

Remington

Remington PRO POWER HC5150 Bedienungsanleitung

Remington

Remington Power X Series Bedienungsanleitung

Remington

Remington Compact Beard Groomer MB-20 Bedienungsanleitung

Remington

Remington X4 Power-X Series Bedienungsanleitung

Remington

Remington HC5810 Bedienungsanleitung

Remington

Remington HC5015 Bedienungsanleitung

Remington

Remington ProPower HC7110 Bedienungsanleitung

Remington

Remington Pro Power Alpha HC5156 Bedienungsanleitung

Remington

Remington HC335 Bedienungsanleitung

Remington

Remington HC363C Bedienungsanleitung

Remington

Remington HC5870AU Bedienungsanleitung

Remington

Remington Heritage HC9100 Bedienungsanleitung

Remington

Remington X4 Power-X Series Bedienungsanleitung

Remington

Remington HC905 Bedienungsanleitung

Remington

Remington HC340 Bedienungsanleitung

Remington

Remington X3 POWER-X Series Bedienungsanleitung

Beliebte Haarschneider Handbücher anderer Marken

Clatronic

Clatronic HSM 800 Bedienungsanleitung

Mellerware

Mellerware MACRO ALDANY MA20001 Bedienungsanleitung

VALERA

VALERA X-Master 652 Bedienungsanleitung

Wahl

Wahl 1870Li Bedienungsanleitung

Lister

Lister Legend Bedienungsanleitung

Philips

Philips HC5440/80 Bedienungsanleitung

Andis

Andis MBA 23125 Bedienungsanleitung

Philips

Philips Philishave HQC488/61 Bedienungsanleitung

Shear Magic

Shear Magic Nifty 1800 Bedienungsanleitung

Philips

Philips QC5390 Bedienungsanleitung

Andis

Andis US-1 Kurzanleitung

Panasonic

Panasonic EH-KA81 Bedienungsanleitung

Philips

Philips HC5450 Bedienungsanleitung

Andis

Andis US-1 Montageanleitung

Andis

Andis ML Montageanleitung

O'Barber

O'Barber MINI SLIDE Bedienungsanleitung

Oster

Oster 76110 Bedienungsanleitung

Hyundai

Hyundai HC 420 Bedienungsanleitung