Remington AIR3D D7777XAU Bedienungsanleitung

3 YEAR WARRANTY D7777XAU

AIR3D®STYLING GIFT SET

USE & CARE

MANUAL

PLEASE READ

PRIOR TO USE

To register your product go to

www.remington-products.com.au

www.remington.co.nz

IMPORTANT SAFEGUARDS

Warning: When the appliances are used in a bathroom, unplug

it after use since the proximity of water presents a hazard even

when the appliances are switched off.

When using electrical appliances, especially when children are

present, basic safety precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE USING

KEEP AWAY FROM WATER

DANGER – As with most electrical appliances, electrical parts are

electrically live even when the switch is off.

To reduce the risk of death by electric shock:

• Always unplug it immediately after using.

• Do not place or store an appliance where it can fall or be pulled into a

bath or sink.

• Do not use while bathing.

• Do not place or drop into water or other liquid.

• If an appliance falls into water, “unplug it” immediately.

Do not reach into the water.

For additional protection, the installation of a residual current device (RCD)

with a rated residual operating current not exceeding 30mA is advisable in

the electrical circuit supplying the bathroom. Ask your electrical contractor

for advice.

WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, AND

FIRE, OR INJURY TO PERSONS.

• Do not use the straightener on wet hair.

• An appliance should never be left unattended when plugged in to a

power outlet.

• These appliances are not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliances by a person responsible

for their safety. Keep the appliances and the power cords away from

the edge of table or countertops and out of reach of children and

persons with reduced physical, sensory or mental capabilities.

• These appliances are not toys. Children shall be supervised to ensure

they do not play with the appliances.

• Use these appliances only for their intended uses as described in this

manual. Do not use attachments not recommended by Remington.

• Do not operate this appliance with a damaged cord/plug or after the

appliance has malfunctioned, or been dropped or damaged in any

manner.

• There are no user serviceable parts. If power cord is damaged, it must

be replaced by the manufacturer or similarly qualified person in order

to avoid a hazard.

• Do not use on people who are sleeping.

• Never drop or insert any object into any opening of these appliances.

• Do not use outdoors or where aerosol (spray) products are being used

or where oxygen is being administered.

• When using the hair dryer, do not direct hot air towards the eyes or

other heat sensitive areas.

• Attachments, where provided, may be hot during and after use. Allow

them to cool before handling.

• When using the hair dryer, keep your hair away from the air inlet grille.

Do not let your hair get drawn into it.

• During the use of the straightener, the plates will be very hot. Do not let

bare skin touch heated surfaces.

• Do not place the heated straightener on any soft surface such as

a bed, carpet or a towel. Place only on a hard, flat, heat resistant

surface.

• Please check the voltage ratings on the product prior to use to ensure

it matches the voltage of the local area.

SAVE THESE INSTRUCTIONS

D7777XAU AIR3D®STYLING GIFT SET

HAIR DRYER & STRAIGHTENER

Thank you for purchasing your new Remington®AIR3D®Styling Gift Set.

Our AIR3D®hair dryer features the unique 3D airflow and Smooth

Conditioning Technology. The styling gift set also comes with a special

straightener with suspension plates coated with Advanced Ceramic for a

smooth glide and shiny-looking hair.

HAIR DRYER USE & CARE INSTRUCTION

KEY PARTS

1. Ceramic back-lit grille

2. Air inlet grille

3. Cool shot

4. Heat settings ( )

5. Speed settings ( )

6. Hang loop

7. 7mm ultra slim concentrator

8. 11mm fast drying

concentrator

9. Diffuser

10.Storage pouch (not shown)

BASIC HAIR CARE INSTRUCTIONS

For optimal results, shampoo and condition your hair prior to styling and

towel dry to remove excess moisture.

Note: This hair dryer is not suitable for use on synthetic wigs or hair

extensions.

UNIQUE 3D AIRFLOW TECHNOLOGY

The AIR3D®Hair Dryer features a unique design with 3D Airflow Technology

to deliver precise, evenly heated airflow for optimal styling performance.

SMOOTH CONDITIONING TECHNOLOGY

Besides the ionic generator, this hair dryer is infused with micro-

conditioners to eliminate static hair, smooth down the hair cuticles for

intensified softness, achieving the ultra-smooth finish.

LIGHTWEIGHT & BALANCED

With the motor located vertically in the handle, this hair dryer allows

optimised weight distribution to provide maximum comfort and control.

FITTING ATTACHMENTS

1. Push the desired attachment onto the front of your hair dryer.

2. Concentrator can be rotated as required.

HOW TO USE YOUR REMINGTON®AIR3D®HAIR DRYER

1. Plug the hair dryer into a 220-240V wall power outlet.

Note: Please note this hair dryer is only suitable for use on 220-240V

wall power outlets.

2. Switch the hair dryer on and select the desired speed setting (1 Low

or 2 High) using the speed setting switch ( ). The number below the

switch will light up to show you which setting you have selected. The

back-lit grille will light up white when you switch the hair dryer on.

3. Select the desired heat setting (1 Low, 2 Medium or 3 High) using the

heat setting switch ( ). The number above the switch will light up and

show you which setting you have selected.

4. Press and hold the cool shot button to direct cool air onto your hair to

help set your style. The back-lit grille will illuminate blue when you use

the cool shot feature.

5. After use, turn your hair dryer off and unplug it.

6. Let your hair dryer cool down before cleaning or storing away.

QUICK DRYING

Select the high heat and high speed setting and roughly dry your hair. Use a

brush or your hand to shake out excess moisture whilst drying and keep the

hair dryer in constant motion.

STRAIGHTENING

Select the high heat and high speed setting and roughly dry the hair. When

the hair is nearly dry, attach the concentrator nozzle (which minimises frizz)

and reduce the heat & speed. Section the hair according to thickness and

begin with straightening bottom layers first. Using your brush, follow the

concentrator from above, while slowly gliding down each section of hair

from roots to tips. Once bottom layers have been straightened, then

straighten the mid section and complete by straightening top layers.

NATURAL WAVY TEXTURE

Using the low heat and low speed setting, ‘scrunch’ sections of hair with

your fingers into the palm of your hand while directing airflow through your

fingers. Once you have reached the desired effect, use the cool shot on

each section of hair to hold style. For more volume lean forward and dry

hair in the upside down position.

LIFT & VOLUME

Use the hair dryer on the low heat and low speed setting, work from the

roots of hair and begin at the back of the head. Section your hair and use

a round brush to dry against the natural growth pattern of your hair. This

creates lift at the roots, which creates a style with volume.

STYLING

Set the hair dryer to the low heat and low speed setting and attach the

concentrator nozzle for precision drying. Section the hair and style using a

round brush. Concentrate the airflow directly on the hair while styling in the

direction you desire. If necessary, hold the airflow for 2-5 seconds on each

section while curling under or over for additional hold.

USING THE DIFFUSER

This hair dryer comes with a professional style diffuser. This diffuser dries

hair fast without blowing out the style. Perfect for naturally curly, wavy,

permed and fine hair or to give your hair a boost for volume.

NOTE: Always select the lowest heat setting when using the diffuser, as

damage may occur to the diffuser if higher heat settings are used.

DRY YOUR HAIR USING THE DIFFUSER

Dry your hair beginning at the roots and using the circular motions, always

moving in the same direction. Use the diffuser with the hair dryer set at the

low heat and low speed setting. Continue drying, keeping the hair dryer at

a 90-degree angle to the scalp. This will lift the roots away from the scalp

giving your hair volume. Finish by drying the ends.

ADD VOLUME TO YOUR HAIR USING THE DIFFUSER

To add volume to your hair, tilt your head upside down and dry so that the

roots fall away from your scalp. Use the diffuser with the hair dryer set at

the low heat and low speed setting. Point the hair dryer at the roots to give

your hair maximum volume. Continue the process to the ends of your hair.

Important Note: Remington AIR3D® hair dryer is constructed differently

from other Remington hairdryers. When drying your hair, at all times please

avoid your hair covering the back of the dryer to prevent it from being

caught in the grille.

CLEANING AND MAINTENANCE

To maintain peak product performance and to prolong motor life, it is

important to regularly clean the air inlet grille.

Unplug the hair dryer and allow it to cool.

Use a lint free cloth or soft brush to gently remove dust and debris from the

grille.

KEY PARTS

1. Advanced ceramic coated

plates

2. Indicator light

3. Suspension plates

4. On/off switch & Hinge lock

5. Salon swivel cord

6. Storage case

STRAIGHTENER USE & CARE INSTRUCTION

BASIC HAIR CARE INSTRUCTIONS

For optimal results, shampoo and condition your hair, then dry your hair

thoroughly and make sure that it is tangle free prior to straightening.

NOTE: The AIR3D®Styling Gift Set Straightener is not suitable for use on

synthetic wigs or hair extensions.

ADVANCED CERAMIC COATED PLATES

Advanced Ceramic is an exclusive layer of CeraSol Ceramic. Advanced

Ceramic Coated plates are proven to have 10x more ceramic* for superior

high even heat across the plates with no hot spots. Its 2x smoother*

creating an effortless glide during straightening for silky smooth results and

2x longer lasting* ensuring plate durability.

*vs. standard Remington straightener ceramic coating

HOW TO USE YOUR REMINGTON®AIR3D®STYLING GIFT SET

STRAIGHTENER

Before use, ensure the hair is clean, dry and tangle free. Section the hair

prior to styling and style the lower layers first.

Plug in to any household (120-240V AC) wall power outlet, and move the

on/off switch into the “I” position, this will unlock the plates and also switch

the straightener on. The on indicator light will begin to flash and continue to

flash until the straightener has heated up to 200°C. The straightener will be

ready to use in 30 seconds from switched on. Take extra care when using

the straightener, as it can get very hot. Ensure you test the straightener on

a small section of hair first.

To switch your straightener off, move the on/off switch into the “O” position

but not close the plates and only close the plates once they are fully cooled

down.

TO STRAIGHTEN YOUR HAIR

To make styling easier, part the hair either in the middle or to the side and

use clips to section your hair, top, sides and back.

You may need to comb through your hair before straightening to ensure that

it is tangle free.

Start at the nape of the neck and straighten the underneath sections of hair

first. When the underneath sections of hair are complete, move to the next

layers, finishing with the hair around the part line.

Take about a 5cm section of hair and pull taut and down and away from the

scalp. Holding the straightener with the other hand, start at the roots and

clamp the hair firmly between the plates.

Firmly holding the plates together, run the straightener down through the

entire length of the section of hair from roots to ends, in one smooth stroke.

Repeat until the desired amount of straightening has been achieved.

TO CURL YOUR HAIR

Section your hair as above. Take about a 5cm section of hair and firmly grip

it between the plates, close to the roots. Note: The smaller the section the

tighter the curl.

Keeping tension firm, gently rotate the straightener 180° whilst pulling

through the length of the hair section. Make sure to keep rotating the

straightener. Remove straightener and holding the hair length, allow the

curl to spring into shape.

AUTOMATIC WORLDWIDE VOLTAGE

The AIR3D®Styling Gift Set Straightener features automatic voltage

adjustment for international use. Plug the unit into any domestic power

outlet and it will adjust automatically to the voltage being supplied.

NOTE: Some countries will require the use of a plug adaptor that is not

included with your straightener.

HINGE LOCK

Safely store your AIR3D®Styling Gift Set Straightener with the plates

locked together.

To unlock, slide the hinge lock into the “I” position. To lock, slide the hinge

lock into the “O” position

NOTE: Do not heat the straightener in the locked position. Ensure the plates

are fully cooled down before put away your straightener.

MAINTENANCE

This straightener is designed for household use and is virtually maintenance

free. If cleaning becomes necessary, disconnect the straightener from the

power outlet, allow it to cool, then wipe the exterior surface and the plates

with a soft damp cloth.

Do not immerse the unit in any liquid. Do not use an abrasive cleaning

fluid or material to clean the plates as this will scratch the surface and

deteriorate the effectiveness of the surface.

Inhaltsverzeichnis

Andere Remington Haarstylinggerät Handbücher

Remington

Remington CI89H1 Bedienungsanleitung

Remington

Remington Keratin Protect Auto Curler CI8019 Bedienungsanleitung

Remington

Remington Amaze Smooth and Volume AS1220 Bedienungsanleitung

Remington

Remington AS7700 Bedienungsanleitung

Remington

Remington Protect & Shine S-1006 Bedienungsanleitung

Remington

Remington PROluxe Bedienungsanleitung

Remington

Remington CI9755 Bedienungsanleitung

Remington

Remington Advanced Colour Protect Bedienungsanleitung

Remington

Remington SALON PRO CURL REVOLUTION STYLIST KIT Bedienungsanleitung

Remington

Remington Volume Plus Air Styler Bedienungsanleitung

Remington

Remington Keratin Protect Rotating Air Styler AS8811 Bedienungsanleitung

Remington

Remington AC3000 Installationsanleitung

Remington

Remington PRO-Luxe 32mm Tong CI9132 Bedienungsanleitung

Remington

Remington VINTAGE STYLE S1001GPV Bedienungsanleitung

Remington

Remington ONE Straight and Curl Styler Bedienungsanleitung

Remington

Remington Keratin Protect S8598 Bedienungsanleitung

Remington

Remington S-8600t Bedienungsanleitung

Remington

Remington sleek & smooth wide Bedienungsanleitung

Remington

Remington S91 Series Bedienungsanleitung

Remington

Remington AS8090 Bedienungsanleitung

Remington

Remington Advanced Color Protect Bedienungsanleitung

Remington

Remington S8648AU Bedienungsanleitung

Remington

Remington AS5901 Bedienungsanleitung

Remington

Remington PROtect S8700 Bedienungsanleitung

Beliebte Haarstylinggerät Handbücher anderer Marken

Philips

Philips HP8309 Bedienungsanleitung

Eldom

Eldom bess HTS20 Bedienungsanleitung

Lunata Hair

Lunata Hair LH24HR Originalbetriebsanleitung

Conair

Conair S3CSC Bedienungsanleitung

Dyson

Dyson Airwrap Bedienungsanleitung

Braun

Braun Satin Hair 1 AS 110 Kurzanleitung

REVAMP Professional

REVAMP Professional iGEN PROGLOSS CL-2750 Bedienungsanleitung

Vitek

Vitek VT-2285 Bedienungsanleitung

point

point WAVE VIXEN TRIPLE WAVE MAKER Bedienungsanleitung

Braun

Braun Satin Hair 5 Bedienungsanleitung

Philips

Philips beauty Airstylist quattro 600 Bedienungsanleitung

Grundig

Grundig HS 7230 Bedienungsanleitung

Philips

Philips HP4658/08 Bedienungsanleitung

Vitek

Vitek VT-2296 BK Bedienungsanleitung

HOT TOOLS

HOT TOOLS SIGNATURE Series Installationsanleitung

Conair

Conair INFINITI INFCS25C Bedienungsanleitung

Philips

Philips Norelco RQ111 Stücklistenhandbuch

Clas Ohlson

Clas Ohlson 44-1152 Bedienungsanleitung