RemoteLock openEDGE 700 Series Handbuch
Do this first:
Hardware Installation
1
700 SERIES
MEDIUM DUTY COMMERCIAL LEVERS
MODEL 710 MODEL 720
PLEASE NOTE:
This installation manual uses the 710 model.
However, the installation steps are the same for all
models in the 700 series.
Need some help? Here’s what you’ll need:
Visit us online.
support.remotelock.com
We’re here to help.
1 (877) 254 5625
support@remotelock.com
Four AA Batteries
Phillips Screwdriver
Power Drill
2 ⅛” Hole Saw (optional if the door is not preconfigured
with this hole)
1” (25mm) Drill Bit (for the middle hole and edge
borehole if the door is not preconfigured)
⅜” (10mm) Drill Bit (for the upper two support holes)
Measuring Tape
Adhesive Tape
Install your lock.
Use this Hardware Installation
Guide to get your lock installed.
Get connected.
Use the Connection Guide to get
your lock online and registered.
Take control.
Now your lock is fully functional and
can be managed from anywhere.
11
22
33
You are here. Find more help online.
For additional installation instructions and
troubleshooting tips, be sure to visit our online
support site: support.remotelock.com.
Drilling new holes?
Most doors will have an existing hole drilled for a
lever installation. If your door needs to be drilled,
you’ll need to drill a 2 ⅛“ (54mm) face bore hole for
the lockset on the face of the door, as well as a 1”
edge bore hole for the latch on the edge of the door.
Let’s get
started.
First things first, let’s get
your new lock installed. Face Bore Hole
Edge Bore Hole
for Latch
STEP 1
Position the template.
Crease the template along one of the dotted lines
(60mm (2 ⅜’’) or 70mm (2 ¾’’) latch). Place the template
on the door and position with the existing bore hole.
Once the template is aligned, tape it to the door.
The backset is the distance
from the center of the face
bore hole to the edge of
the door.
Quick Tip
Exterior of Door
STEP 2
Mark carefully and drill.
Use a thumbtack or sharp object to mark the center
of each hole you will drill. Mark the three holes on the
exterior of the door.
Then apply the template to the interior of the door and
mark the holes from this side as well.
Exterior of Door
View the template from
the other side of the
boring hole to make
sure it’s aligned.
Quick Tip
Interior of Door
Remove the template.
Make sure the markings are aligned precisely from one
side of the door to the other and double check all the
measurements and markings before drilling.
Align the drill bit over your mark and hold the door
steady. Keep the drill level and straight. Drill the ⅜”
holes halfway through on the first side. Then drill the
remaining half from the other side of the door. This
prevents damage to the door and improves accuracy.
Exterior of Door
Interior of Door
⅜” (10mm) Drill Bit
DRILL HALFWAY THROUGH
ON EACH SIDE
Repeat these steps for the 1” middle hole.
PLEASE NOTE:
A ½” hole could be drilled instead of a
1” hole if the support tube will not be used.
We use a 1” hole in this example in case the optional
support tube will be used.
Exterior of Door
Interior of Door
1” (25mm) Drill Bit
OPTIONAL:
If you are using a 70mm latch, and would like to use
the fire cup, insert the fire cup into the 54mm (2 ⅛“)
boring hole. Place the open side of the fire cup to face
the keypad side with the small bolt through-hole at the
bottom.
Install the latch using the
screws provided, with the
bevel towards the door frame.
STEP 3
Install the latch.
Make sure the latch plate lays flush with the door. If the latch plate is
not flush with the door, draw an outline around the faceplate edge
and chisel a rebate to allow the latch to lay flush with the door edge.
Quick Tip
X2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
